Surenoo STP0177B-128160 Series TFT LCD Panel User Manual
- June 3, 2024
- Surenoo
Table of Contents
- Surenoo STP0177B-128160 Series TFT LCD Panel
- General Description
- Mechanical Specification
- Mechanical Dimension
- Electrical Maximum Ratings
- Backlight Characteristic
- Module Function Description
- Response time&Contrast ratio
- Viewing Angle
- Inspection standards
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Surenoo STP0177B-128160 Series TFT LCD Panel
Shenzhen Surenoo Technology Co.,Ltd.
Skype : Surenoo365
General Description
MODEL NO
| STP0177B-128160
---|---
Display Mode
| ****
Transmissive
Display Format
| ****
Graphic 128RGB*160 Dot-matrix 128xRGBx160
Input Data
| ****
SPI-4wire interface
Viewing Direction
| ****
12 o’clock 12
Drive
| ****
ST7735S
Mechanical Specification
| Item | Specifications | Unit |
|---|
Dimensional outline
| 34.00(W)45.83(H)2.25+/-0.1(T)
(FPC not include)
| mm
Resolution
| 128RGB*160| dots
LCD Active area
| 28.03 (W)*35.04 (H)| mm
Pixel size
| 0.219(W)*0.219(H)| mm
Mechanical Dimension
Electrical Maximum Ratings
Item
| Symbol
| Min
| Max
| Unit
| Note
---|---|---|---|---|---
Supply voltage （ IOVCC ）
| V| 1.8| 3.3| V|
Supply voltage （ IOVCC ）
| V| 2.8| 3.3| V|
Operating temperature 工
| T OPR| -20| 70| ℃|
Storage temperature
| T STR| -30| 80| ℃|
Backlight Characteristic
Item
| Symbol
| Min
| Typical
| Max
| Unit
---|---|---|---|---|---
LED module Forward voltage
| V LED| 2 ． 8| 3.0| 3.2| V
LED module current
| I LED| –| 30| –| mA
LCD Surface Luminance
| L S| 150| 200| –| Cd/m2
LCM Surface brightness uniform
| L D| 80| –| –| %
Module Function Description
PIN No.
| Symbol
| Description
| Notes
---|---|---|---
1| NC| No connection
|
2| GND| Ground
|
3| LED-| Cathode of Backlight
|
4| LED+| Anode of Backlight
|
5| GND| Ground
|
6| /RESET| LCM Reset pin.Signal is active low
|
7
| ****
A0
| Register select pin（
RS=’0’: Display data. RS=’1’: Display data.
|
8| SDA| Serial data input / output.
|
9| SCK| Serial clock pin.
|
10| VCC| Power supply for LCM
2.8-3.3V)
|
11| IOVCC| Power supply for LCM
1.8-3.3V)
|
12| CS| Chip select pin (“Low” enable)
|
13| GND| Ground
|
14| NC| No connection
|
Response time&Contrast ratio
Item
| Symbol
| Condition
| Remark| Unit
---|---|---|---|---
Min.
| Typ.
| Max.
Response time
| Tr+Tf| θ=0°| –| 30| 60| ms
Contrast ratio
| CR| θ=0°| 200| 300| –|
Viewing Angle
Item
| Symbol
| Condition
| Remark| Unit
---|---|---|---|---
Min.
| Typ.
| Max.
Viewing angle
| Top
| CR≥10
| 20| 30| –| ****
Deg.
度
Bottom
| CR≥10
| 40| 45| –
Left
| | | 45| –
Right
| | | 45| –
Reliability Trial
NO.
| ITEM
| CONDITION
| CRITERION
---|---|---|---
1| High Temperature Non-Operating Test| 80℃120Hrs| No Defect Of
| Operational
2| Low Temperature Non-Operating Test| -30℃120Hrs| Function In Room
| Temperature Are
3| High Temperature/Humidity Non Operating Test| 60℃90%RH120Hrs| Allowable
|
4| High Temperature Operating Test| 70℃72Hrs|
|
5| Low Temperature Operating Test| -20℃72Hrs|
|
6| Thermal Shock Test| -20 ℃ (30Min) n 70 ℃|
| (30Min) *10CYCLES|
Inspection standards
Glass defect
| NO | Defect item | Criteria | Remark |
|---|
1
| Dimension Unconformity
(Major defect)
| By Engineering Drawing|
2
| Cracks
(Major defect)
| 1. Linear cracks panel
【Reject】
2. Nonlinear crack contrast by limited sample
| ****
3
| Glass extrude the conductive area
(minor defect)
| a: disregards and no influence assemblage.
1) b≤1/3Pin width(non bonding area)
【Accept】
- bonding area≤0.5mm
【Accept】
| A: Length, b: Width
4
| Pin-side ,conductive area damaged
(minor defect)
| (a c: disregards)
b≤1/3of effective length for bonding electrode
【Accept】
| a: length, b: Width, c: Thickness
5| Pin-side,non-conductive
area damaged
| 1)Damage area don’t touch the ITO
(Inclueling contraposition mark,
| a: Length, b: Width c: Thickness
| (minor defect)| except scribing mark)
【Accept】
- C<T b≦BM1/3of width
【Accept】
- c=T
b not touch the seal glue
【Accept】
- a disregards
| ****
---|---|---|---
6
| Non-pin-side damage
(minor defect)
| c<T
1)b exceeds 1/3Bm
【Reject】
c=T
b not touch the seal glue
【Reject】
| c: Thickness b: width of
damage
LCD appearance defect(View area)
| NO | Defect item | Criteria | Remark |
|---|
1
| ****
Fiber、glass cratch、polarizer scratch/folded
(minor defect)
| Specification| Allowable| note1:L: Length, W: Width note2: disregard if out of AA
W≦0.03mm| disregard
0.03mm<W≦0.05mm;
L≦3.0mm
| 2
0.05mm<W≦0.1mm;
L≦3.0mm
| 1
W>0.1mm;L>3.0mm| 0
2
| Polarizer bubble、 concave and convex
(minor defect)
| φ≦0.2mm| disregard| note1: φ=(L+W)/2,L:Length,
W :Width
note2:disregard if out of AA
0.2mm<φ≦0.3mm| 2
0.3mm<φ≦0.5mm| 1
0.5mm<φ| 0
3
| ****
Black dots、dirty dots、 impurities、eye winker
(minor defect)
| φ≦0.15mm| disregard| note2:disregard if out of AA
0.15mm <φ≦0.25mm| 2
0.25mm<φ≦0.3mm| 1
0.3mm<φ| 0
4
| ****
Polarizer prick
(minor defect)
| φ≦0.1mm| disregard| note1: φ=(L+W)/2,L=Length,
W=Width
note2:the distance between two dots>5mm
0.1mm<φ≦0.25mm| 3
φ>0.25mm| 0
Package Method
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>