SOUNDIGITAL 3000.1 EVO5 Amplifier Owner’s Manual
- June 4, 2024
- SOUNDIGITAL
Table of Contents
- INTRODUCTION
- PACKAGE CONTENTS
- SAFETY INSTRUCTIONS
- DISASSEMBLING OF THE PLASTIC COVER
- PANELS DESCRIPTION
- ELECTRICAL DIMENSIONING AND AUDIO INPUTS
- AUDIO INPUTS
- INSTALLATION SEQUENCE
- WIRING DIAGRAM
- SD RLC / REGULAGEM DO GANHO
- TECHNICAL SPECS
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
OWNER´S MANUAL
3000.1
INTRODUCTION
DEAR CUSTOMER, CONGRATULATIONS ON ACQUIRING A PRODUCT WITH THE HIGHEST QUALITY
AND TECHNOLOGY!
You have just purchased a SounDigital product of the highest technology and
quality, so we thank you for your confidence.
Class D Amplifiers:
Class D amplifiers have as their main characteristics audio quality,
efficiency, application versatility, and compact design. Following are the
advantages of these features:
Audio Quality – In the past, Class D products had limited response and for
higher frequencies, Class AB products performed better, but their efficiency
was very low.
The new technologies introduced by SounDigital resulted in a Class D amplifier
with high efficiency and superior Class AB performance.
Efficiency – SounDigital Class D amplifiers have total efficiency (output +
power source) greater than 70%, which guarantees lower battery consumption and
less heating.
Application Versatility – The flat full-frequency response of SounDigital
amplifiers allows them to be used in all car sound systems. Meeting the
demands with extreme quality.
Compact Design – The high efficiency and high technology applied, allows
SounDigital amplifiers to be very compact, facilitating installation in
vehicles where space is limited.
IMPORTANT INFORMATION
In this manual, you will learn about the product, its features, and its
characteristics, in order to obtain the best result and to be able to enjoy
your music with SounDigital quality and power.
To better understand and take advantage of all the functions of the product
and use it safely, read this manual carefully and if you have any questions,
consult our support by email at
info@soundigitalusa.com.
PACKAGE CONTENTS
- 01 3000.1 EVO5 Amplifier
- 01 Installation quick guide with warranty card
- 01 Promotional sticker
SAFETY INSTRUCTIONS
To prevent injuries to the user or damage to the amplifier, read all safety
instructions written in this manual;
If you are insecure about the installation of this equipment, get in touch
with our tech support or with a professional specializing in car audio
installation;
Before proceeding with the installation of any electric equipment on your
vehicle, unplug the negative (-) terminal of the battery to avoid fires,
injuries, or damages;
Use your sound system safely. Continuous exposure to sound pressures over 85dB
may cause irreversible hearing damage;
This equipment is for use in automotive DC voltage batteries between 12.6 and
14.4 volts. Before installing the equipment, check the voltage of the
batteries;
Do not install the amplifier in places exposed to water, dirt, or humidity;
Choose a ventilated place to install the amplifier and avoid blocking the side
ventilation windows;
Mount the amplifier in a secure way. Avoid mounting it on metallic parts of
the vehicle, because it may cause ground looping (noise);
Make sure that the location chosen for the amplifier installation does not
affect the operation of the vehicle;
When passing cables through metallic walls, use rubber O-rings to avoid cable
cutting and short-circuits;
Clean the amplifier periodically with a brush or dry cloth to assure the
thermal efficiency of the heatsink;
This product may reach temperatures over 60°C/140°F. Make sure it is cold
before touching it;
Be careful when making holes in the vehicle. Make sure you are not making
holes in the fuel tank, brake lines, or electrical cables of the vehicle;
Make sure the cables are properly secured throughout the installation;
Wear gloves, safety glasses, and all necessary PPE during the installation of
SounDigital amplifiers.
Warning!
THIS “WARNING” SIGN ALERTS THE USER OF IMPORTANT INFO. NOT FOLLOWING THIS
INSTRUCTION MAY CAUSE INJURIES TO THE USER OR DAMAGE TO THE EQUIPMENT.
ASSEMBLING AND DISASSEMBLING THE PLASTIC COVER
The plastic covers have the function of finishing and hiding the amplifier
fixing screws. To disassemble and assemble them, follow the instructions
below.
DISASSEMBLING OF THE PLASTIC COVER
- Carefully pull out the top of the plastic cover to release the upside latches, as shown in picture 1.
- Slide up the plastic cover in a continuous movement to remove it.
ASSEMBLING THE PLASTIC COVER
- To fit the plastic cover back, carefully insert point A of the plastic cover into point B of the amplifier, slowly sliding it down.
- Gently press the sides of the top of the plastic cover towards the bottom of the amplifier until you hear a clicking noise.
PANELS DESCRIPTION
1| Left Channel Right Channel| Audio input – High Level
(To connect to the speaker output of the head unit)
---|---|---
2| Left Channel| Audio input RCA connectors
3| Right Channel
4| –| Variable Gain control
5| –| Low Pass filter “ON/OFF” switch
6| –| Variable “LOW PASS” filter control (50Hz ~ 1kHz)
7| –| Variable “SUBSONIC” filter control (5Hz ~ 80Hz)
8| –| Variable “BASS BOOST” control 50Hz (0dB ~ +12dB)
9| –| Remote level control connector
10 | Speakers output connectors | Negative speaker connector (-) |
---|---|---|
11 | Positive speaker connector (+) | |
12 | – | Minimum speaker load allowed (impedance) |
13 | – | Positive power supply connector (+12VDC) |
14 | – | Remote power supply connector (REM) |
15 | – | Negative power supply connector (GND) |
ELECTRICAL DIMENSIONING AND AUDIO INPUTS
ELECTRICAL DIMENSIONING
For proper operation of your SounDigital amplifier, you need the proper
dimensioning of the electrical system and the cables used.
The table below shows the minimum section of GND cables, +12VDC cables, and
speaker output cables according to the power generated by the amplifier.
We recommend the use of ONLY OFC (Oxygen Free Copper) Cables on the installation of our products. CCA cables must not be used.
AUDIO INPUTS
RCA inputs
All RCA Inputs must be connected for all channels to work properly. If the signal source is monotype, use the “Y” cable at the input.
High-Level input
All High-Level Inputs must be connected for all channels to work properly.
High-level input must be used when the main unit does not have RCA outputs.
When High-level inputs are used, no remote connection is required, and the
amplifier recognizes the audio signal and switches on.
If your source unit is not able to turn on the amplifier through the High-
level input, the remote input should be connected normally.
Warning!
RCA AND HIGH INPUTS SHOULD NOT BE USED SIMULTANEOUSLY OR YOU MAY DAMAGE THE
AMPLIFIER.
INSTALLATION SEQUENCE
Warning!
BEFORE PROCEEDING WITH THE INSTALLATION, UNPLUG THE NEGATIVE TERMINAL FROM
ALL OF THE BATTERIES, TO AVOID FIRE, AND DAMAGE TO THE AMPLIFIER AND THE USER
HIMSELF.
- Mount the amplifier in such a way you have access to the connectors;
- Install the power cables in the vehicle properly, starting from the battery to the fuse holder or circuit breaker, use the cable with the appropriate size. Make all connections, and install fuse holders or circuit breakers, but without placing the fuses or with the circuit breakers in the “OFF” position;
Warning!
THE MAXIMUM DISTANCE FOR THE INSTALLATION OF THE FUSE/CIRCUIT BREAKER IS 12
INCHES (30cm) AWAY FROM THE BATTERY.
-
Connect the power cables to the amplifier, observing the polarity. Connect all the positive cables from the fuse holder or circuit breaker to the positive connector of the amplifier and all the negative power cables from the batteries to the negative connector of the amplifier;
-
The ground cable must be as short as possible and must be connected to the vehicle chassis and the battery negative;
-
Install the signal input cables in a proper way, distant from the power cables;
-
Connect the RCA or the high-level signal input cables to the head unit and amplifiers;
-
Install the audio output cables with the appropriate section, distant from the power and audio input cables;
-
Connect the audio output cables to the amplifier and speakers respecting the positive (+) and negative (-) polarities;
-
Install the remote cable with the power cables, using a 1.5mm² (15 AWG) cable or thicker;
-
Connect the remote power cable to the amplifier’s “REM” terminal at the main unit’s remote power output (when not using the high-level signal inputs);
-
Before powering the system, verify all the connections and make sure there are no mistakes or short-circuits on the power and ground cables;
-
Reconnect the ground of the batteries;
-
Check if the head unit is turned off and then place the fuses in the fuse holders or switch the circuit breakers on;
-
Turn on the main unit and the amplifier will turn on the “ON” LED indicating that it is in operation.
WIRING DIAGRAM
1 CHANNEL WIRING DIAGRAM
All RCA Inputs must be connected for all channels to work properly. If the signal source is monotype, use the “Y” cable at the input.
SD RLC / REGULAGEM DO GANHO
*EXTERNAL LEVEL CONTROL – SD RLC (NOT INCLUDED)**
The SD RLC is an easy-to-install external level control accessory that allows
you to tune the level of SOUNDIGITAL amplifiers that have remote level
control.
In SD RLC, you can adjust the amplifier level without having to lean over and
adjust the gain setting on the amplifier and can monitor the “CLIP” LED which
is also available on the accessory.
GAIN SETTING
Necessary equipment:
- Digital AC voltmeter;
- Media with sine wave test tone 60Hz recorded at 0db;
Set up procedure
- This procedure is the same for both gain controls;
- Turn the gain control all the way down;
- Disconnect the output cables from the amplifier outputs;
- Turn off all processing (bass, treble, loudness, EQ, etc.);
- Set the source unit volume to 3/4 of full volume;
- On the CD player set the fader control to the center position;
- Set the LP selector switch in “OFF”;
- Use a 60Hz sine wave;
- Connect the AC voltmeter to the speaker output connectors of the amplifier. Make sure you test the voltage at the correct connectors (+ and –);
- Increase the gain control until the target voltage is observed with the voltmeter (see the chart below);
- Once you have adjusted the amplifier to its correct voltage output, turn off the source unit and reconnect the speaker(s).
Download the tracks for set up at https://soundigitalusa.com/tracks-forset- up/
MODEL | POWER | OUTPUT VOLTAGE |
---|---|---|
3000.1 1Ω | 1 Ω/ 3000W | 54,8 V |
3000.1 2Ω | 2 Ω/ 3000W | 77,5 V |
3000.1 4Ω | 4 Ω/ 3000W | 109,5 V |
CROSSOVER SET UP
Using Bass Boost
The Amplifier Bass Boost setting enables the user to boost the sound intensity
at low frequencies of the sound system, where boost intensity can be adjusted.
This is a semi-parametric equalizer type circuit with the ”Q” value for the
fixed filter, with an intensity boost adjustment from 0 to + 12dB (16 times),
and a central frequency adjustment of the filter in 50Hz, making it versatile
for several types of sound systems.
How to Adjust Bass Boost
Reproduce your favorite song and set the boost intensity between 0dB and +12dB
at the variable control level according to your preference.
How to Adjust the Crossovers
For full range application, select the LP key in the “OFF” position and the
“SUBSONIC” variable control at 5Hz. All frequencies will be reproduced
according to the figure below;
To set the “SUBSONIC” variable control between 5Hz and 40Hz (“A”) where you want to perform the subsonic cut filter;
Set in the “LOW” variable control between 50Hz and 500Hz (“B”) where you want to perform the low pass cut filter and select the “LP” key in position “ON”;
TECHNICAL SPECS
PARAMETERS | 3000.1 1Ω | 3000.1 2Ω | 3000.1 4Ω |
---|---|---|---|
Power RMS @ 4Ω** | 1307W | 1980W | N/A |
Power RMS @ 2Ω** | 1980W | 3000W | 3000W |
Power RMS @ 1Ω** | 3000W | N/A | N/A |
Frequency Response (-3dB) | 5Hz ~ 25kHz | 5Hz ~ 25kHz | 5Hz ~ 25kHz |
Subsonic filter | 5Hz ~ 80Hz | 5Hz ~ 80Hz | 5Hz ~ 80Hz |
Low Pass filter (12dB/oct) | 50Hz ~ 1kHz | 0dB ~ 12dB @ 50Hz | 0dB ~ 12dB @ 50Hz |
Bass Boost | 0dB ~ 12dB @ 50Hz | 50Hz ~ 1kHz | 50Hz ~ 1kHz |
Operating Voltage | 8V ~ 16V | 8V ~ 16V | 8V ~ 16V |
SNR | 92dB | 92dB | 92dB |
Input Sensitivity (RCA) | 0.2V ~ 2V | 0.2V ~ 2V | 0.2V ~ 2V |
Input Sensitivity (High-Level input) | 1.2V ~ 12V | 1.2V ~ 12V | 1.2V ~ 12V |
Current draw (music) | 149A | 139A | 280A |
Current draw (max.) | 298A | 277A | 140A |
Total efficiency | 80% | 86% | 85% |
Damping factor (@100Hz nominal impedance) | >2000 | >2000 | >2000 |
Power cable | 35mm² (2 AWG) | 35mm² (2 AWG) | 35mm² (2 AWG) |
Audio output cable | 2 x 6.0 mm² | ||
9 AWG | 2 x 4.0 mm² | ||
11 AWG | 2 x 2.5 mm² |
13 AWG
Fuse* (music)| 150A| 150A| 150Ah
Recommended battery (minimum)| 150Ah| 150Ah| 150A
*It is mandatory to install the fuse at a maximum distance of 12 inches from the battery.
Power at 12.6V @ 60Hz with a maximum THD of 1%.
**Power Rating according to CTA-2006 Industry Standards**
DIMENSIONAL DATA
Net Weight | 1,65 kg (3.64 lb) |
---|---|
Gross Weight | 1,77 kg (3.90 lb) |
YOUR MUSIC. YOUR POWER.
WWW.SOUNDIGITALUSA.COM
SOUNDIGITALUSA
**** SOUNDIGITALUSA
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>