SounDigital EVO 4.0 Amplifier Owner’s Manual

SounDigital EVO 4.0 Amplifier

Dear Customer,
Congratulations on acquiring your Soundigital! You’ve just purchased a product of high quality and technology. The Sun digital products are developed to assure maximum efficiency and reliability to your sound system.
Class D amplifiers:
The main characteristics of Class D amplifiers are audio quality, efficiency, versatility and compact design. Here are the advantages of these characteristics:

Audio Quality – Class D amplifiers used to have a limited response in the past and they used to have a worse performance regarding higher frequencies thanClass AB amps, despite being more efficient. Introducing new technologies, Soundigital developed a Class D amplifier superior to the Class AB ones in efficiency and performance.

Efficiency – The Soundigital Class D amplifiers have a total efficiency (power source + output) higher than 70%, assuring battery consumption and a heating lower than expected.

Versatility of uses – The flat response of all the frequencies of Soundigital amplifiers allows them to be used in all the kinds of systems: SPL, Sound Quality, Trio Eletrico and Pancadao, meeting the needs with extreme quality.

Compact design – The high efficiency and technology allow our amplifiers to be really compact, making it easy to install them in vehicles where you have limited space.

IMPORTANT INFO
Read this manual and follow its instructions and information carefully. It contains extremely important information to have your amplifier working properly. If you feel the need to contact our Tech Support, you can reach o u r t e c h n i c i a n s t h r o u g h t h e e – m a i l sac@soundigita.com.

PACKAGE CONTENTS

• 1 EVO4.0 Amplifier
• 1 Installation quick guide with warranty card
• 1 Promotional sticker

Warning!
THIS “WARNING” SIGN ALERTS THE USER OF IMPORTANT INFO. NOT FOLLOWING THIS INSTRUCTION MAY CAUSE INJURIES TO THE USER OR DAMAGE TO THE EQUIPMENT.

ASSEMBLING AND DISASSEMBLING THE PLASTIC COVER

The plastic covers have the function of finishing and hiding the amplifier fixing screws. To disassembling and assembling them, follow the instructions below.

DISASSEMBLING OF THE PLASTIC COVER

1. Carefully pull out the top of plastic cover to release the upside latches, as shown in picture 1.
2.  Slide up the plastic cover in a continuous movement to remove it.

ASSEMBLING THE PLASTIC COVER

1. To fit the plastic cover back, carefully insert the point A of the plastic cover into point B of the amplifier, slowly sliding it down.
2. Gently press the sides of the top of the plastic cover towards the bottom of the amplifier until you hear a clicking noise.

PANELS DESCRIPTION

ELECTRICAL DIMENSIONING AND AUDIO INPUTS

ELECTRICAL SIZING
For a correct operation of your SounDigital amplifier, it is necessary to properly size the electrical system and the cables used.
In the table below you can determine the minimum proper section of the grounding, positive + 12VDC, and audio output cables according to the amplifier power.

For the connections from the battery to the amplifier and to ground, use good quality copper cables.
CCA cables should not be used.

AUDIO INPUTS

RCA Entry

High Signal Inputs

High input must be used when the main unit does not have RCA outputs.
When hi inputs is used, no remote connection is required, the amplifier recognizes the audio signal and switches on.
If your source unit is not able to turn on the amplifier through the high level input, the remote input should be connected normally.
RCA AND HIGH INPUTS SHOULD NOT BE USED SIMULTANEOUSLY OR YOU MAY Warning! DAMAGE THE AMPLIFIER..

INSTALLATION SEQUENCE.

• Mount the amplifier in such a way you have access to the connectors;
• Install the power cables in the vehicle properly, starting from the battery to the fuse holder or circuit breaker, use the cable with the appropriate size. Make all connections, install fuse holders or circuit breakers, but without placing the fuses or with the circuit breakers in the “Off” position.
• Connect the power cables in to the amplifier, observing the polarity. Connect all the positive cables from the fuse holder or circuit breaker to the positive conector of the amplifier and all the negative power cables from the batteries to the negative connector of the amplifier;
• The ground cable must be as short as possible and must be connected to the vehicle chassis and the battery negative;
•  Install the signal input cables in a proper way, distant from the power cables;
• Connect the RCA or the high signal input cables to the head unit and amplifiers;
• Install the audio output cables with the appropriate section , distant from the power and audio input cables;
• Connect the audio output cables to the amplifier and speakers respecting the positive (+) and negative (-) polarities;
• Install the remote cable with the power cables, using 1.5mm² (15 AWG) cable or thicker;
• Connect the remote power cable to the amplifier’s “REM” terminal at the main unit’s remote power output (when not using the high level signal inputs);
• Before powering the system, verify all the connections and make sure there are no mistakes or short-circuits on the power and ground cables;
• Reconnect the ground of the batteries;
• Check if the headunit is turned off and then place the fuses in the fuse holders or switch the circuit breakers on;
• Turn on the main unit and the amplifier will turn on the “On” LED indicating that it is in operation.

WIRING DIAGRAM

GAIN SETING

Necessary equipment:

• Digital AC voltmeter;

• Media with sine wave test tone 60Hz recorded at 0db;

• Screwdriver 1/8″ ( for gain set)
  Set up procedure

• This procedure is the same for both gain controls;

• Turn the gain control all the way down.

• Disconnect the output cables from the amplifier outputs;

• Turn off all processing (bass, treble, loudness, EQ, etc.);

• Set the source unit volume to 3/4 of full volume.

• Set the source unit’s fader control to center position;

• Set the crossover selector switch in “F»

• Use a 60 Hz sine wave

• Connect the AC voltmeter to the speaker output connectors of the amplifier. Make sure you test the voltage at the correct connectors (+ and –);

• Increase the gain control until the target voltage is observed with the voltmeter (see the chart below);

• Once you have adjusted the amplifier to its correct voltage output, turn off the source unit and reconnect the speaker(s)
  Download the tracks for set up in https://soundigital.com/en/downloads/

CROSSOVER SET UP

“F” All the frequencies are reproduced;
“LP ” Frequencies below 80Hz will be reproduced; “HP ” Frequencies above 80Hz will be reproduced.

• Switch Key to “F” position (Full Range): All the frequencies are reproduced.
• Switch Key to “HP” position (High Pass): Frequencies above 80Hz will be reproduced;
• Switch Key to “LP” position (Low Pass): Frequencies below 80Hz will be reproduced;

TECHNICAL SPECS

Power at 12.6V @ 60Hz with maximum THD of 1%.
It is mandatory to install the fuse at a maximum distance of 30cm from the battery.

DIMENSIONAL DATA

References

• Downloads - SounDigital

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>