ROCKVILLE RMWK8 V2 8 AWG RMWK V2 Series Marine Amplifier Wiring Kits Owner’s Manual

RMWK V2 Series
Marine Amplifier Wiring Kits
Owner’s Manual

RWK Series High Power Amp Wiring Kit

Thank you for purchasing this RMWK Series Marine Amplifier Wiring Kit. No expense has been spared in the engineering and manufacturing of this kit. All cables and accessories have been tested and are sure to meet the highest quality standards. If properly installed this kit will provide you with years of uninterrupted service. Please read this installation guide carefully for proper use of your RMWK Series wiring kit. Read the entire guide before attempting your installation. Should you need assistance, please call our helpline at 1-646-758-0144, 24 hours a day/7 days a week.

Attention

Before you begin your installation, disconnect the NEGATIVE ( – ) terminal from your vessel’s battery. This safety precaution will avoid possible short circuits while wiring your amplifier.
It is recommended that you lay out your sound system design on paper first. This will help you during the installation so that you will have a wiring flow chart and not miss-wire any of your components. Be sure to observe proper polarity when wiring the speakers.
Always run the RCA cables on the side of the vessel opposite to the side used to route the power and ground leads of the amplifier. The high-quality, shielded RCA patch cords included with this kit reduce and eliminate unwanted electrical noise to your system. Cheaper cables usually have poor shielding that can cause interference pickup.

Fuse Installation

1. Securely mount the fuse holder 18 inches or less from the house battery.
2. Cut power cable to the proper length. Trim half an inch of the power cable insulation and insert it into one end of the fuse holder. Screw it down tightly. Attach a large ring connector to the other end. Secure it to the POSITIVE ( + ) terminal of the house battery.

Power Cable

1. Depending on the location of your fuse block (see page 2), cut an appropriate length section of the power cable. Trim half an inch of insulation from both ends. Attach a ring connector to one end and attach it to the POSITIVE (+) terminal of the HOUSE BATTERY (a). Insert the other end into the fuse holder. Screw it down tightly (see page 2).
2. Cut another section of power cable long enough to go from the fuse holder to the amplifier. Trim half an inch of insulation from both ends. Insert one end into the fuse holder (see page 2). Route the power cable through the firewall and along the inside of the vessel to the amplifier (b). Make sure to run it on the side opposite the RCA cables. Insert the other end into the POSITIVE (12V+) terminal of your amplifier (c). Screw it down tightly.

Ground Cable

1. Cut the ground cable to the appropriate length and trim half an inch of insulation from both ends. Attach a ring connector to one end and attach it to the NEGA-TIVE (—) terminal of the house battery (a).
2. Route the ground cable through the firewall and along the inside of the vessel to the amplifier (b). Make sure to run it on the side opposite the RCA cables. Now insert the other end into the amplifier’s GROUND (GND) terminal (c). Screw it down tightly.

Remote and RCA

1. Ensure that the head unit is turned off.
2. Connect the RCA cables to the head unit (a) and route through the inside of the vessel to the amplifier (b). Connect to the RCA inputs on the amplifier (c).
3. Make sure that you run the RCA cables on the side opposite the power cable.
4. Connect the blue remote cable to the remote turn-on terminal of the head unit (d). Route through the inside of the vessel to the amplifier (e). Connect to the amplifier terminal marked REMOTE (REM)(f).

Diagram

ATTENTION: WATCH THIS VIDEO BEFORE FIRST USE!
Who reads manuals?
Scan the OR code or go to the URL of the appropriate kit to access the how-to video(s), the owner’s manual, and other important information you may need to get the most out of your item.
If you prefer written instructions, please read ahead!
With Rockville, you get many options.

http://rockvillesupport.com/rmwk4-v2

|

http://rockvillesupport.com/rmwk8-v2

---|---

RockvilleAudio.com
©2022 ROCKVILLE
The information presented is subject to change and/or improvement without notice.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>