GALAX Revolution 02 PC Case User Manual

June 3, 2024
GALAX

GALAX Revolution 02 PC Case

Please take a moment to carefully go through the user manual. Galax will not take responsibility for any damages incurred due to incorrect installation and usage of this product.

For more information to visit www.galax.com

CASE SPECIFICATION INTRODUCTION

Model No. Galax Revolution-02
Materials Chassis 0.6 mm SPCC, tempered glass on

left side panel

Motherboard support| EATX(272305mm)、ATX、M-ATX、ITX
PSU type| ATX PSU (Bottom located)
TOP panel I/O ports| USB3.0
2+USB2.02, HD Audio, Light control key
HDD bay| 3.5” HDD
2 , 2.25 SSD2
Expansion Slots| 7 slots , Support up to 355mm (Max.) VGA card
CPU Cooler Height| 170mm
Fan Cooler| Front: 2
120mm or 2140mm Fan
Top: 2
120mm or 2140mm Fan
Rear: 1
120mm
Liquid cooling| Front: 120/140/240/280 water cooling Radiator
Top: 120/140/240/280 water cooling Radiator
Rear: 1*120mm
Chassis size| (L)390 x (W)210 x (H)445mm
Case size| (L)438 x (W)210 x (H)468mm

GALAX-Revolution-02-PC-Case-FIG1

CHASSIS BREAKDOWN DRAWINGS

GALAX-Revolution-02-PC-Case-FIG2

  1. Chassis main body
  2. Left tempered glass side panel
  3. Right side panel
  4. Power supply box
  5. Dust-proof filter on front panel
  6. Dust-proof filter at top panel
  7. SSD bracket
  8. Cabel management box
  9. Fan control board box
  10. HDD Bracket
  11. VGA card bracket
  12. VGA card installation position
  13. Rear fan installation position
  14. Front fan installation position
  15. LED strips

I/O PORTS INTRODUCTION

  1. Power Switch
  2. Reset button
  3. RGB LED light control
  4. HD Audio
  5. USB 2.0
  6. USB 3.1 GEN1

SIDE PANEL INSTALLATION INSTRUCTION

  1. Loose the drop-proof screws A, pull out the right side panel toward to the arrowhead direction.
  2. loose the drop-proof screws A, hold the hand-holding position then pull out the side panel to the angle as picture two then pull up the side panel as the arrowhead direction.

POWER SUPPLY INSTALLATION

GALAX-Revolution-02-PC-Case-FIG6

  1. Remove the right side panel,then put into the PSU according to the arrowhead direction.
  2. Fix the screws

MOTHERBOARD INSTALLATION

GALAX-Revolution-02-PC-Case-FIG7

  • Pre-installed 6 motherboard screws in factory setting
  • Put the motherboard into the right position according to the arrowhead direction, the fix the screws

HDD AND SSD INSTALLATION

HDD installation

GALAX-Revolution-02-PC-Case-FIG8

  • Remove the front pane , hold the front panel like the pictures then pull out the front panel.
  • Fix the HDD into the HDD tool-less bracket accoding to the step ①/② then put inside the HDD bracket into the HHD slots obey to the arrowhead direction

SSD installation

GALAX-Revolution-02-PC-Case-FIG9

  • Remove the screws, take off the SSD bracket.
  • Assembly the SSD, fix the screws.
  • Install the SSD into the chassis which is near to top and left edge of the M/B bracket, put it into the right position then fix.
  • Fix the screws, installation finish

DISASSEMBLY FOR DUST-PROOF FILTER

Pull out the dust -proof filter according to the arrowhead direction

VGA CARD HOLDER INSTALLATION

GALAX-Revolution-02-PC-Case-FIG11

  • VGA Card Holder
  • Put the holder into the situable position on the motherboard plate according to the VGA
  • Fix the screws at the rear side of the motherboard plate

Move the VGA card holder

GALAX-Revolution-02-PC-Case-FIG12

  • loose the handy screws, move the holder to the situable position towards to the arrowhead direction according to the VGA card length, the fix it.
  • move the holder toward to the arrowhead direction according to the VGA card width, then fix it well.
  • move the holder toward to the arrowhead direction according to the VGA card thickness, then fix it well.

FAN COOLER AND LIQUID COOLING INSTALLATION

Fan Support:

  • Front: 120mm x2 or 140mm x2
  • Top: 120mm x2 or 140mm x2
  • Rear: 120mm x1

Liquid cooling support:

  • Front: 120/140/240/280mm
  • Top: 120/140/240/280mm
  • Rear: 120mm x1

GLASS SIDE PANEL INSTALLATION

GALAX-Revolution-02-PC-Case-FIG15

  1. Find the bolt on the glass panel
  2. Aligning the bolt into the hole then insert into
  3. Then install well the glass panel as picture, fix the screw

Installation

GALAX-Revolution-02-PC-Case-FIG16

  • Fix the iron column to the bracket with a sleeve
  • Fix the PCI-E 16X cable on the VGA bracket
  • Install the VGA card at the appropriate position on the bracket from up to the downsideGALAX-Revolution-02-PC-Case-FIG17
  • Install and fix the bracket from the VGA card the bottom side
  • Remove the PCI-E strips
  • Fix the bracket on the chassis according to the arrow point direction

FAN CONTROL BOARD CONNECTION INSTRUCTION

GALAX-Revolution-02-PC-Case-FIG18

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals