Micro-Star QCNCM865 Application User Guide

WiFi 7/BT Combo module
QCNCM865

Introduction

The QCNCM865 module is designed to support Wi-Fi 7 and Bluetooth applications that support 2.4/5/6GHz, 2 streams 802.11a/b/g/n/ac/ax/be, and Bluetooth 5.1. The card uses the Microsoft Windows Client Utility (ACU) which is a user-mode utility designed to edit and add profiles for selected network interface adapters.
This module requires professional installation and can be only assembled in a Microsoft Windows laptop/tablet by system manufacture.

System Requirements

• Laptop/ PC containing:
  • 32-bit PCI Express Bus
  • 32 MB memory or greater
  • 300 MHz processor or higher
• Microsoft Windows 10

Profile Management

Configure the wireless network adapter (wireless card) from the Profile Management tab of the Client Utility.

◆ Add a profile
Edit a profile
Import a Profile
Export a Profile| Order profiles
Switch to a different profile
Remove a profile
Connect to a Different
Network
---|---

The wireless network adapter works in either infrastructure mode (which uses an access point) or ad hoc mode (a group of stations participating in the wireless LAN).

Create or Modify a Configuration Profile
To add a new configuration profile, click New on the Profile Management tab. To modify a configuration profile, select the configuration from the Profile list and click the Modify button.
The Profile Management dialog box displays the General tab. In profile management:

• Edit the General tab.
• Edit the Security tab.
• Edit the Advanced tab.

To configure a profile for ad hoc or access point (infrastructure) mode, edit the Network Type field on the Advanced tab.
Note that the ACU only allows the creation of 16 configuration profiles. After the creation of 16 profiles, clicking the New button displays an error message. Remove an old profile or modify an existing profile for a new use.
Remove a Configuration Profile

1. Go to the Profile Management tab.
2. Select the profile to remove from the list of configuration profiles.
3. Click the Remove button.

Auto Profile Selection Management

Including a profile in the auto selection feature allows the wireless adapter to automatically select that profile from the list of profiles and use it to connect to the network.

Including a profile in auto profile selection:

1. On the Profile Management tab, click the Order Profiles button.
2. The Auto Profile Selection Management window appears, with a list of all created profiles in the Available Profiles box.
3. Highlight the profiles to add to auto profile selection, then click Add. The profiles appear in the Auto Selected Profiles box.

Ordering the auto selected profiles:

1. Highlight a profile in the Auto Selected Profiles box.
2. Click Move Up, Move Down, or Remove as appropriate. The first profile in the Auto Selected Profiles box has highest priority, and the last profile has lowest priority.
3. Click OK.
4. Check the Auto Select Profiles box.
5. Save the modified configuration file.

When auto profile selection is enabled by checking Auto Select Profiles on the Profile Management tab, the adapter scans for an available network. The profile with the highest priority and the same SSID as one of the found networks is the one that is used to connect to the network. If the connection fails, the adapter tries the next highest priority profile that matches the SSID, and so on.
With auto profile selection enabled, the wireless adapter scans for available networks.
The highest priority profile with the same SSID as a found network is used to connect to the network. On a failed connection, the adapter tries with the next highest priority profile.

Switching to a Different Configuration Profile

1. To switch to a different profile, go to the Profile Management tab.
2. Click on the profile name in the Profile List.
3. Click the Activate button.

The Profile List provides icons that specify the operational state for that profile. The list also provides icons that specify the signal strength for that profile.

Import and Export Profiles

Importing a Profile

1. From the Profile Management tab, click the Import button. The Import Profile window appears.
2. Browse to the directory where the profile is located.
3. Highlight the profile name.
4. Click Open. The imported profile appears in the profiles list.

Exporting a Profile

1. From the Profile Management tab, highlight the profile to export.
2. Click the Export button. The Export Profile window appears.
3. Browse to the directory to export the profile to.
4. Click Save. The profile is exported to the specified location.

Scan Available Networks
Click the Scan button on the Profile Management tab to scan for available infrastructure and ad hoc networks. On this list, click Refresh to refresh the list at any time.

Connecting to a different network
◆ Highlight a network name and click the Activate button to connect an available network. If no configuration profile exists for that network, the Profile Management window opens to the General tab. Fill in the profile name and click OK to create the configuration profile for that network.

Tray Icon

The tray icon appears at the bottom of the screen, and shows the signal strength using colors and the received signal strength indication (RSSI).Hold the mouse cursor over the tray icon to display the current configuration profile name and association, as well as transmit and receive speed and the wireless adapter name and IP address. Right-click on the tray icon to:

configure a profile or view status and statistics information.
Troubleshooting| Run the Troubleshooting Utility.
Preferences| Set the ACU startup and menu options. Check to start the program automatically when Windows starts, and check
menu items that should appear on the popup menu.
Enable/Disable Radio| Enable or disable the RF signal.
Manual LEAP Login| Log in to LEAP manually, if LEAP is set to manually prompt for user name and password on each login.
Reauthenticate| Reauthenticate to the access point.
Select Profile| Click a configuration profile name to switch to. If no configuration profile exists for a connection, add a profile.
Show Connection| This window displays connection information:
Status
Active Profile| Displays the active configuration profile name.
Auto Profile|
Selection| Shows whether auto profile selection is enabled.
Connection Status| Displays whether the adapter is connected to a wireless network.
Link Quality| Lists the quality of the link connection.
SSID| Displays the SSID of the associated network.
Access Point Name| Shows the name of the AP the wireless adapter is connected to.
Access Point IP Address| Shows the IP address of the access point the wireless adapter is connected to.
Link Speed| Lists the speed of the link connection.
Adapter IP Address| Displays the IP address of the wireless adapter.
Exit| Exit the Client Utility application.

The colors are defined as follows:

*Received signal strength indication RSSI. Displayed in dB or percentage. Enable or disable the tray icon in the Action

Federal Communication Commission Interference Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules.

Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
This module is intended for OEM integrators only. Per FCC KDB 996369 D03 OEM Manual, the following conditions must be strictly followed when using this certified module:
KDB 996369 D03 OEM Manual rule sections:
2.2 List of applicable FCC rules
This module has been tested for compliance to FCC Part 15
2.3 Summarize the specific operational use conditions
The module is tested for standalone mobile RF exposure use condition. Any other usage conditions such as co-location with other transmitter(s) or being used in a portable condition will need a separate reassessment through a class II permissive change application or new certification.
2.4 Limited module procedures
Not applicable.
2.5 Trace antenna designs
Not applicable.
2.6 RF exposure considerations
This equipment complies with FCC mobile radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. If the module is installed in a portable host, a separate SAR evaluation is required to confirm compliance with relevant FCC portable RF exposure rules.
2.7 Antennas
The following antennas have been certified for use with this module; antennas of the same type with equal or lower gain may also be used with this module. The antenna must be installed such that 20 cm can be maintained between the antenna and users.

Antenna Set| RF Chain No.| Brand| Model| Antenna Net Gain
(dBi)| Frequency Range| Cable Loss (dB)| Antenna Type| Connector Type| Cable Length
---|---|---|---|---|---|---|---|---|---
1| Chain0/1| Hong-Bo| 260-25094| 3.53| 2.4∼2.4835GHz| 0.74| PIFA| MHF 4L| 300mm
3.06| 5.15∼5.25GHz| 1.16
3.07| 5.25∼5.35GHz| 1.18
4.81| 5.47∼5.725GHz| 1.26
4.2| 5.725∼5.850GHz| 1.28
2| Chain0/1| Hong-Bo| 260-25083| 5.09| 5.850∼5.895 GHz| 1.29| PIFA| MHF 4L| 300mm
5.14| 5.925∼6.425 GHz| 1.35
5.09| 6.425∼6.525 GHz| 1.38
5.16| 6.525∼6.875 GHz| 1.45
5.12| 6.875∼7.125 GHz| 1.50
3| Chain0/1| Hong-Bo| 260-25084| 3.22| 2.4∼2.4835 GHz| 0.49| Monopole| MHF 4L| 200mm
3.35| 5.150∼5.250 GHz| 0.76
3.42| 5.250∼5.350 GHz| 0.77
4.77| 5.470∼5.725 GHz| 0.80
4.72| 5.725∼5.850 GHz| 0.84
4.71| 5.850∼5.895 GHz| 0.84
4.75| 5.925∼6.425 GHz| 0.86
4.29| 6.425∼6.525 GHz| 0.91
4.81| 6.525∼6.875 GHz| 0.96
4.74| 6.875∼7.125 GHz| 0.98

2.8 Label and compliance information
The final end product must be labeled in a visible area with the following: “Contains FCC ID: I4L-QCNCM865”. The grantee’s FCC ID can be used only when all FCC compliance requirements are met.
2.9 Information on test modes and additional testing requirements
This transmitter is tested in a standalone mobile RF exposure condition and any co-located or simultaneous transmission with other transmitter(s) or portable use will require a separate class II permissive change re-evaluation or new certification.
2.10 Additional testing, Part 15 Subpart B disclaimer
This transmitter module is tested as a subsystem and its certification does not cover the FCC Part 15 Subpart B (unintentional radiator) rule requirement applicable to the final host. The final host will still need to be reassessed for compliance to this portion of rule requirements if applicable.
As long as all conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.

IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module.
The end user manual shall include all required regulatory information/warning as show in this manual.

OEM/Host manufacturer responsibilities
OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The final product must be reassessed against all the essential requirements of the FCC rule such as FCC Part 15 Subpart B before it can be placed on the US market. This includes reassessing the transmitter module for compliance with the Radio and EMF essential requirements of the FCC rules. This module must not be incorporated into any other device or system without retesting for compliance as multi-radio and combined equipment
FCC 6GHz Statement
Prohibited for control of or communications with unmanned aircraft systems, including drones.

Industry Canada statement

This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with greater than 20cm between the radiator & your body.

This device is intended only for OEM integrators under the following conditions: (For module device use)

1. The antenna must be installed and operated with greater than 20cm between the antenna and users, and
2. The transmitter module may not be co-located with any other transmitter or antenna.
   As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.

IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or colocation with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization.

End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed and operated with greater than 20cm between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains IC: 3715A-QCNCM865”.

Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module.
The end user manual shall include all required regulatory information/warning as show in this manual.

Caution:

(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
(ii) for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;
(iii) for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits as appropriate;
(iv) where applicable, antenna type(s), antenna models(s), and worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in section 6.2.2.3 shall be clearly indicated.

ISED 6GHz Statement
a. Operation shall be limited to indoor use only; and
b. Operation on oil platforms, cars, trains, boats and aircraft shall be prohibited except for on large aircraft flying above 10,000 ft.

DETACHABLE ANTENNA USAGE

This radio transmitter [IC:3715A-QCNCM865] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.

Antenna
Set| RF Chain
No.| Brand| Model| Antenna Net Gain (dBi)| Frequency Range| Cable Loss (dB)| Antenna Type| Connector Type| Cable Length
---|---|---|---|---|---|---|---|---|---
1| Chain0/1| Hong-Bo| 260-25094| 3.53| 2.4∼2.4835GHz| 0.74| PIFA| MHF 4L| 300mm
3.06| 5.15∼5.25GHz| 1.16
3.07| 5.25∼5.35GHz| 1.18
4.81| 5.47∼5.725GHz| 1.26
4.2| 5.725∼5.850GHz| 1.28
2| Chain0/1| Hong-Bo| 260-25083| 5.09| 5.850∼5.895 GHz| 1.29| PIFA| MHF 4L| 300mm
5.14| 5.925∼6.425 GHz| 1.35
5.09| 6.425∼6.525 GHz| 1.38
5.16| 6.525∼6.875 GHz| 1.45
5.12| 6.875∼7.125 GHz| 1.50
3| Chain0/1| Hong-Bo| 260-25084| 3.22| 2.4∼2.4835 GHz| 0.49| Monopole| MHF 4L| 200mm
3.35| 5.150∼5.250 GHz| 0.76
3.42| 5.250∼5.350 GHz| 0.77
4.77| 5.470∼5.725 GHz| 0.80
4.72| 5.725∼5.850 GHz| 0.84
4.71| 5.850∼5.895 GHz| 0.84
4.75| 5.925∼6.425 GHz| 0.86
4.29| 6.425∼6.525 GHz| 0.91
4.81| 6.525∼6.875 GHz| 0.96
4.74| 6.875∼7.125 GHz| 0.98

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>