OLIGHT Warrior 3S Flashlight User Manual

June 3, 2024
OLIGHT

OLIGHT Warrior 3S Flashlight

OLIGHT-Warrior-3S-Flashlight-PRODUCT

Thank you for purchasing this Olight Product. Please read this manual carefully before use and keep it for future reference!

IN THE BOX

OLIGHT-Warrior-3S-Flashlight-FIG 1

SPECIFICATIONS

OLIGHT-Warrior-3S-Flashlight-FIG 2

  • All above specifications are test results based on ANSI/NEMA FL1-2009 Standard. The tests are performed using the battery included in the flashlight. Note: The maximum output brightness will decrease as the battery voltage decreases

BATTERY INSTALLATION

Before first use, please unscrew the tailcap and remove the insulating film. If the battery needs to be replaced, make sure that the positive end of the new battery faces the flashlight head when you put it in.OLIGHT-Warrior-3S-
Flashlight-FIG 3

AVAILABLE BATTERIES

  • 1 x customized 5000mAh 21700 rechargeable lithium battery

INDICATORS ON BOTH SIDES

NOTE: While the light is on, if the battery power is less than 10%, the lowest indicator on the right side will glow red.

USB MAGNETIC CHARGING CABLE — MCC3

Parameter Specification

  • Charging cable USB type A – magnetic charging connector, length: 0.5m

  • Input USB A – Type DC 5V 2A

  • Charging pattern CC&CV

  • Maximum charging current 2A

  • Voltage of fully charged battery 4.2V±0.05V

  • Time to fully charge
    5.5 hours (For reference only. When the USB power source is insufficient to provide 5V 2A power capacity, the charging time will be longer)

  • Charge indication
    Red: charging
    Green: full (over 95%) or disconnected with flashlight

CHARGING

OLIGHT-Warrior-3S-Flashlight-FIG 5

  • Before first use please fully charge the product.
  • Connect the USB end of the magnetic charging cable to an external USB power source, then attach the other end of the cable to the charging port of the light (best charging efficiency with a 10W (5V 2A) USB power source). The red indicator means charging, while the green indicator means charging completed (battery level>95%).
  • Only charge with standard MCC3, not compatible with other MCC.

PROXIMITY PROTECTION FUNCTION

When the light is on and set at level 3 or higher brightness, if the front lens proximity sensor detects an obstruction nearby, the brightness will automatically reduce. The brightness will restore when the obstruction is gone. The light will turn off directly if the blockage continues for more than 1 minute.
To disable the proximity sensor, please quickly double click (or triple click) the side switch within 5 secondsafter the automatic dimming. Then, the brightness will restore to the normal level. Turning off the light can re- activate the proximity sensor.

ATTENTION

  • The built-in sensor may NOT work if it is blocked by water or dirt on the front lens. Please keep the lens clean to ensure that it works properly.
  • Please protect the surface of the front lens carefully. If there are scratches on the surface of the front lens, the light output may be automatically dimmed by mistake.
  • While pressing and holding the tail switch or the magnetic remote switch to momentarily access high, turbo, or strobe mode, if the front lens proximity sensor detects an obstruction nearby, the brightness will automatically reduce. The light will turn off automatically if the obstruction continues for more than 1 minute.

DANGER

  • DO NOT shine the light directly into human eyes. This may cause temporary blindness, or permanent damage to the eyes.
  • DO NOT cover the flashlight’s head or place thehead on the ground when the flashlight is on. The radiation energy may cause damage to the flashlight itself, or even result in the burning of flammable objects nearby.
  • The battery can only be charged while installed in the flashlight.

WARNING

  • DO NOT activate turbo mode repeatedly under high temperature to prevent the flashlight body from overheating and hurting the user’s hand.
  • The tail switch may not work while immersed in sea water or other conductive media. Please try to keep it clean and dry.
  • DO NOT use Non-protected rechargeable batteries.
  • DO NOT use the battery if the wrapper is broken, or in any other compromised state.
  • Please lock out the switches if the flashlight is left unused, carried, or transported. The heat built-up due to accidental activation may melt the lens of the flashlight, cause close objects to burn, or even result in unexpected disasters.
  • Store the battery with care. If the battery needs to be changed, please take good care of the battery taken out. Do not mix it with the conductive metals
  • DO NOT clean the lens with alcohol or any other chemicals.

NOTICE

  • When the flashlight is turned off, the current mode will be memorized. The modes that can be memorized are: moonlight, low, medium, and high mode (after the light is turned off, high mode will be memorized for 1 minute before reverting to medium mode). Strobe and turbo mode cannot be memorized.
  • DO NOT short-circuit the tail switch cap with the surrounding ring. A short circuit in this case will result in a weak electric discharge between them and may lead to a complete battery drain if it is in this state for too long.
  • The magnetic tail is easy to attract iron debris. Please keep the tail switch cap and the ring surrounding it clean.

HOW TO OPERATE

SIDE SWITCH

ON/OFF: Single click the side switch to turn the light ON/OFF. When the light is turned on again, it will return to the previously memorized mode.

CHANGE BRIGHTNESS LEVEL: When the flashlight is on, press and hold the side switch and it will, starting from the present brightness level, automatically cycle through Low, Medium, and High mode. The mode is selected when the side switch has been released. (Please note: moonlight, turbo and strobe are not in the automatic cycle).

MOONLIGHT MODE: When the flashlight is off, press and hold the side switch for over one second to access the moonlight mode. If the memorized mode is moonlight, simply click the switch to access it.

TURBO AND RETURN: Fast double click on sideswitch to enter into Turbo, double click again to return. If memory mode were High or Medium, the output is Medium; if memory mode were Low or Moonlight, the output is memory mode.

STROBE: Quickly triple click the side switch to enter the strobe mode. To quit this mode, single click or press and hold the side switch.

LOCK/UNLOCK: When the flashlight is off, press and hold the side switch (for about 2 seconds) to access the button lockout mode (the flashlight will enter the moonlight mode first and then switch off to signal the lockout mode). In lockout mode, if you press and hold the side switch for less than one second or use the tail switch, the indicator to the right of the side switch will light up red at the lowest level for two seconds to signal that the light is still in lockout mode. To unlock it, keep holding the side switch for over one second until the moonlight mode is on again.

TAIL SWITCH

The flashlight produces different output settings by pressing lightly or hard on the tail switch (please refer to the following program configurations).

TWO DIFFERENT PROGRAM CONFIGURATIONS CONFIGURATION 1 (FACTORY DEFAULT SETTING) :

Half press for Medium, hard press for Turbo; Single press the tail switch (press and release quickly) to turn the flashlight on or off; Press and hold the tail switch for momentary on. Release to turn off.
CONFIGURATION2: Half press for Turbo, hard press

WARRANTY

Within 30 days of purchase: Contact the original seller for repair or replacement.

Within 5 years of purchase: Contact Olight for repair or replacement.

Battery warranty: Olight offers a one year warranty for all rechargeable batteries.

MCC USB magnetic charging cable : One year.
For any of the fragile or low-value fittings notcovered above, like lanyard and clip, you can contact the post-sale within 30 days of the purchase, if it has any quality drawback or damage under normal use condition. If such drawback or damage occurs after 30 days of the purchase or under abnormal use condition, we will only offer conditional quality assurance as appropriate.

https://olightworld.com/ec-declaration

USA Customer Support

[email protected]

Global Customer Support

[email protected]

Visit www.olightworld.com to see our complete product line of portable illumination tools.

References

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals