MYATU AM4143 Ebike E-Folding Bike User Manual

June 3, 2024
MYATU

MYATU AM4143 Ebike E-Folding Bike User Manual
MYATU AM4143 Ebike E-Folding Bike

Safety Instruction

Thank you for purchasing the MYATU E-BIKE. The E-BIKE features the most recent innovation in technology. For Safety reasons, it is most important that you read this user’s manual before you operate the bike. Improper handling can reduce its riding performance and most importantly, cause danger to your safe and healthy .For handling and maintenance of the bicycle, please refer to the E-BIKE user’s manual which is an integral part of this e-bike user’s manual !

IMPORTANT

  • heck the tires for proper inflation and cracks of the tires. Keeping the tires  properly inflated and maintained will help prevent flats and damage.
  • heck all cables and cable housings for fraying, breaks, rust, or corrosion and replace if necessary.
  • heck the brakes to make sure that both are working properly. Additionally, check the brake pads for any damage as they will be worn over time and  eventually need replacement.
  • Check all nuts and bolts are taut and properly fastened to prevent injury  and unnecessary wear and tear on your e-bike.
  • Do not at any time dismantle or assemble any of the above e-bike components!
  • Comply with local laws and regulations when riding this product. Do not ride where prohibited by local laws.
  • To reduce risk of injury, you must read and follow all “CAUTION” and “WARNING” notices in this document. Do not ride at an unsafe speed. Under no circumstance should you ride on roads with motor vehicles.
  • Anyone whose weight is outside the stated limits (see Specifications) is  prohibited from riding.
  • Use only MYATU approved parts and accessories. Do not modify your E-bike. Modifications to your E-bike could interfere with the operation of the E- bike, could result in serious injury.
  • E-bike cannot be used as off-road vehicles or extreme cycling sports.
  • Don’t change the default speed setting of the E-bike for your safety concern.  Wear a helmet and protective gear when riding.
    This manual is intended as a general guide to your new ACNHEER e-bike and not a comprehensive reference guide. For technical support, including service, maintenance, and repair information, please contact us for more information about our e-bike.

General Information

  1. About the MYATU Electric Bike
    MYATU electric bike is a leading icon of e-bikes. For years, MYATU has been not only dedicating to innovation, cutting-edge technology and high-quality materials, but also providing cost effective e-bikes, to satisfy riders’ various needs of transportation and even desire of exploring sports & outdoors life. Just ride freely with MYATU!

  2. What’s In the Box (Parts List)


Description Quantity
MYATU Electric Bike 1
Quick Release Skewer 1
User Manual 1
Key 2
Charging Adapter 1
Battery 1
Pedal 2
Reflector 1
Saddle 1
Saddle Tube 1
Kickstand 1
Stem 1
Front & Rear Fender 2
Tools Bag 1

Note: We will decide whether to include throttle accessories in your product
package in accordance with local laws and regulations.

3. Bike Components

Producte Overview

Meter operation

1. Meter instruction

2. Meter Operation
Operating instructions

To switch on/off the E-Bike system, hold the “M” button for 2s. The default value is “low” pedal assist level.

Press “+” to crease into pedal assist level “Mid”.

Press “+” again to move into pedal assist level “High”. “High” is the maximum power of PAS.

Full Electric Function (Pureelectric mode): Press“-”, until all the three “low”,“Mid”, “High” indicators are off.

3. Operation Cautions

Be careful of the safety use. Don’t attempt to release the connector when charging the battery.

  • Avoid the risk of collision.
  • Don’t modify system parameters to avoid parameters disorder. Operating instructions  To switch on/off the E-Bike system, hold the “M” button for 2s. The default value is “low” pedal assist level. Press “+” to  crease into pedal assist level “Mid”. Press “+” again to move into pedal assist level “High”. “High” is the maximum power of PAS. Full Electric Function (Pure electric mode): Press“-”, until all the three “low”,“Mid”, “High” indicators  are off. 5

Battery: Further Information and Maintenance

  • How far full charge battery can go? That depends on the loading weight, road condition and battery capacity. But in the same condition, can continuous longer travel range.
  • When storing the battery for a longer time, (during winter time) it is important to place the fully charged battery in a dry place.
  • Attention: The battery should be re-charged once every 2-3 month when it is not used.

WARNING

  • Keep the battery out of reach for children.

  • Never try to open the battery.

  • Only use the MYATU supplied battery. Do not use a battery from any other different product models.

  • If the battery is damaged because it has been dropped somewhere or biking
    accident, there may be a risk of electrolytes leakage. Beware of chemical burns! And immediately stop using the damaged battery.

  • Do not touch the battery without a cloth or gloves and make sure no acid touches your eyes.

  • Do not store the battery in temperatures above 95°F or below 23°F.

  • Do not allow the battery to run down completely before charging. Charge the battery before storing the product. If the battery is completely empty, it may cause the battery to no longer charge.

  • Charge a new battery for at least 4-6 hours before you use it in your product for the first time. Never charge the battery too long per time. Overheating or undercharging the battery may shorten battery life and decrease product run time.

Dustbin Icon

IMPORTANT: BATTERY DISPOSAL

  • Battery must be recycled or disposed of in an environmentally sound manner.
  • Do not dispose of the battery in a fire. The battery may explode or leak.
  • Do not dispose of a battery in your regular household trash.
  • When charging the bicycle, just plug the charger into the bicycle battery. Note: The plug hole is located in the left of the battery.
  • You can charge the bike directly, or you can remove the battery for charging.
  • The RED light indicates it is in charging and GREEN light indicates the battery is fully charged. (Please put off plug from wall) Usually the charging time is 4- 6 hours depends on the battery capacity remain.

WARNING:

  • Charging time over 10 hours is prohibited please kept it away from high
    temperature environment and stores it in a cool place.

  • Please make sure that the battery charger and charging plug are always kept dray and never get wet.

  • The charger should only be cleaned with a dry cloth. Never use a wet cloth, oil or any other liquid.

  • Do not connect positive and negative terminals.

  • Stop the charging procedure immediately if you notice anything unusual.

  • It is strictly forbidden to cut the battery charging and discharging lines.

  • It is strictly forbidden to disassemble the battery box or modify the internal structure and protection board of the lithium battery.

  • Only use the MYATU supplied charger. Do not use a charger from any other different product models.

  • After using the battery, please charge it within 12 hours.

Installation Instruction

Installation Instruction

When open the bike’s carton box, take out E-bike and use tools to cut off  the package strings.

Install Kickstand.

  • Unscrew the screw in the kickstand.
  •  Install the kickstand.
  •  Then tighten with tool.

3. Install Stem and Handlebar.

Install Stem and Handlebar.           Install Stem and
Handlebar.     Install Stem and
Handlebar.
3.1 Insert the stem and tighten the screw.

Install Stem and Handlebar
Using the wrench from tool kit to loosen the four screws and put the stem into the bike in balance and you can adjust the handlebar in a property angel and position.

4. Install Front Wheel.

Install Front Wheel.

Take out the front fork protector from the front fork.
(Please note: Front fork protector is used to prevent the forks from being deformed during transport. It belongs to the packing material. You can just throw away this accessory!)

Wheel Overview

Take out the quick release from Wheel and unscrew the bolt from the quick release.

Installe front wheel

Ensure that the installation direction of the front wheels is correct. Make sure fork hanger hold onto wheel axle, and make sure the disc put into middle of brake.

Installe front wheel

Insert quick-release axle into spring and tighten screw(Quick release nut to be at the same end as the brake).

5. Install Front Light and Front Fender.

Install front light
Screw front light right on front fork holder as shown.

6. Install Pedal.Install Pedal
There is a right pedal marked “R” and a left pedal marked “L”.

Padel mark
The pedal marked “R” has right-hand threads. Tighten it in a clockwise direction.The pedal marked “L” has left-hand threads. Tighten it in a counterclockwise direction (anti-clockwise). Turn the right pedal marked “R” into the right side of the crank arm, and the left pedal marked “L” into the left side of the crank arm.

  • Make sure the threads of each pedal are fully into the crank arm.
  • Make sure pedals are fully tightened with wrench.
  • Note:Be sure to identify R/L letters on pedal’s bolt when you installing.

7. Install Seat Tube and Rear Fender.

Install seat
First connect the seat and the seat tube.

Install seat

Insert seat post into post receiver, set right its position and adjust height to fit your ridding habit. Then, Tighten seat by clamp.

Install the rear Fender
Install the rear Fender.

Install break lever

8. Adjust angle of brake lever, meter, gear shifter, throttle and louder controller on handlebar, then tightens them with tools.
9. Install Battery.

  • Open the box of battery.
  •  Connect the connectors.
  •  Put the battery in bag and lock tighten the belts.

Install throttle

10. Change Throttle.
(Make sure the throttle complies with local laws)

  • Take right side grip.
  •  Install throttle, lock the throttle by tools.
  • Open controller box and take out controller.

CAUTION:

Connect the connection socket

Controller box has 4 screws, loose them by tool, box is easy destroyed by wrong operation.

  •  Connect the connection socket between the throttle valve and the controller.

Warranty

Year Limited Hardware Warranty

Your MYATU Electric bike includes a One Year Limited Hardware Warranty. The Warranty covers product defects in materials and workmanship under normal use. This Warranty is limited to original purchasers. This Warranty starts on the date of your purchase and lasts for one year (the “Warranty Period”). The Warranty Period is not extended if the Product is repaired or replaced.

Warranty services are provided by the e-bike. If a hardware defect arises and a valid claim is received within the Warranty Period, at its option and to the extent permitted by law, MYATU will resend new parts that are equivalent to new in performance and reliability. This Warranty is not assignable or transferable. The original purchaser may contact us for service request.

This Warranty does not cover any damage due to: improper use; failure to follow the product instructions or to perform any preventive maintenance; unauthorized repair; external causes such as accidents, abuse, or other actions or events beyond our reasonable control.

  • Any question about the item, please contact the customer service from where you brought your device.

Attachment: technical parameters

Performance index Project Parameter
Basic Parameters Vehicle Size

Wheel Size

Body Material

Maximum Load

Vehicle Weight

|           17506501080mm

26 Inches

Aluminium Alloy

187 lbs (85KG)

53 lbs (24KG)

Main Parameters of the Whole Vehicle| Maximum Speed

Maximum Gradient              Front Derailleur

Rear Derailleur

Mileage Range

Working Temperature

| 15.6 mph (25km/h)

10 Degrees

3-Speed

7-Speed

18~20 miles (30-33km)

23°F-95°F (-5℃~35℃)

Battery Parameters| Battery Parameters

Battery Capacity

Service Life

| 36V

10.4Ah

1000 Times

Motor Parameter| Motor Power

Motor Type

Maximum Torque

| 250W

Brushless Gear Motor

34N.M

Charger Parameters| Input Voltage

Input Current

Output Voltage

Output Curren

| 100-240V

1.8A

42V

2A

If the product has problems with the following forms during the protection period,
we will provide customer service as part of the product quality guarantee.

Accessories quality problem Warranty period service content
Motor Motor will not be able to use A year Free delivery of parts
Accelerator Natural conditions (such as impact force cannot be used except
damage) A year Free delivery of parts
Controller Failure occurs under normal use A year Free delivery of parts
Charger Failure occurs under normal use A year Free delivery of parts
Lithium Battery Can’t charge discharge under normal use A year Free

delivery of parts

Notes:
If the above issues occur during the protection period, please contact us and send
us photos or videos of the defective parts. If we confirm that the fault is caused by
the quality of the product itself, we will send you the parts that are needed
replaced for free.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals