OLIGHT Odiance Rechargeable Work Lamp User Manual
- June 3, 2024
- OLIGHT
Table of Contents
OLIGHT Odiance Rechargeable Work Lamp
IN THE BOX
SPECIFICATIONS
WHITE LIGHT MODE
YELLOW LIGHT MODE
HIGH ; LOW
- White Light Mode
- 75m
- 20m
- Yellow Light Mode
- 70m
- 18m
1,500cd 0.8m IPX5 1670g / 58.9oz
(L)8.74(W)2.99(H)7.4in (Including the Ordinance-RC)
REMOTE CONTROL DISTANCE
Indoors: The radius ≤ 10M Outdoors: The radius ≤ 6M
All above specifications are test results based on ANSI/NEMA FL1-2009 Standard. The tests are performed indoors under a room temperature of 25 degrees Celsius with windless conditions. The runtime may vary depending on the external temperature and ventilation conditions, and these biases may affect the results of testing.
PRODUCT OVERVIEW
HOW TO RECHARGE
Please charge the product before first use. Connect one end of the provided USB-C cable to an external USB-C power source (power adapter not included), open the silicone dust plug that shields the USB-C charging port, and then insert the other end of the cable into the USB-C charging port.
Standard Charging Time: About 5.5 Hours (30W PD Fast Charging)
BATTERY LEVEL
NOTE:
Use a 30W or higher USB power source for the fastest charging possible. When
charging with a USB power source that is less than 30W, charging times will be
extended.
BATTERY LEVEL INDICATOR
When the product is turned on or being discharged, the battery-icon indicator
displays the remaining battery level. 
BATTERY LEVEL：
Replace Remote Controller Battery
INSTALLATION
NOTES:
- Devices operating at 400-470MHz microwave signal such as walkie-talkies may interfere with remote control.
- The remote control only supports one-to-one control. One-to-many control may cause it to work improperly.
- After being turned off for 48 hours, the product will enter sleep mode, which will cause the remote control to stop working. You can turn the product back on again with the power rotary knob.
- You can control the product with the remote controller and rotary knob simultaneously.
- If the remote control fails due to disoperation, please pair again following the operating instructions.
DANGER
- DO NOT shine the light directly into human eyes. This may cause temporary blindness or permanent damage to the eyes.
- DO NOT cover the product when it is on. The heat built-up may cause close objects to burn or even result in unexpected disasters.
- If the product goes hot, please DO NOT place it in a backpack, fabric bag, or fusible plastic container.
WARNING
- DO NOT store the product in car or other places where the temperature may exceed 60 ℃.
- DO NOT disassemble the product.
- DO NOT immerse the product in liquid, which may damage it.
- Fully charge the battery before storing the product for a long period of time.
- DO NOT use it nearby open flames.
NOTICE
- When the charging port is not in use, keep the port dust cover closed to prevent the entry of dust or other foreign matters.
- Please charge the product with a 30W or higher-capacity USB-C power adapter to achieve the fastest charging possible.
- Please keep the product away from radios, as the PWM modulation of the rotary knob may cause noise to the radio signals.
- Brightness level will be capped at 30% if the battery is lower than 40%.
- High mode will stay on for 10 minutes and then steps down to a 50% brightness level within 5 minutes.
- The maximum brightness level is capped at 30% in the charging state.
EXCLUSION CLAUSE
Olight is not liable for damages or injuries sustained resulting from the
usage of the product inconsistent with the warnings in the manual.
HOW TO OPERATE
LEFT ROTARY KNOB (POWER)
ON/OFF: Rotate the knob clockwise to turn on or counterclockwise to turn off. Stepless Adjustment of Brightness: While the light is on, rotate the knob clockwise to increase brightness or counterclockwise to decrease brightness.
RIGHT ROTARY KNOB (COLOR TEMP.)
Change Color Temperature: While the light is on, rotate the knob clockwise to
decrease color temperature or counterclockwise to increase color temperature.
Note: The color temperature ranges from 2700K to 6000K within 10 levels.
Each position of the rotary knob corresponds to one level.
REMOTE CONTROL
- Single press to turn the light on or increase the brightness by one level (10 levels available). Long press for 0.5 seconds to access the brightest setting directly.
- Single press to turn the light off or decrease the brightness by one level (10 levels available). Long press for 0.5 seconds to turn it off directly.
- While the light is on, single press to increase the color temperature by one level (10 levels available) until it reaches 6,000K. Long press for 0.5 seconds to reach 6,000K directly.
- While the light is on, single press to decrease the color temperature by one level (10 levels available) until it reaches 2,700K. Long press for 0.5 seconds to reach 2,700K directly.
Remote Control Pairing: After turning off the light, please complete the
following steps within 10 seconds: quickly rotate the right rotary knob
clockwise for 3 positions, counterclockwise for 3 positions, and then
clockwise again for 3 positions. If the light flashes slowly for 10 seconds,
it has entered the pairing mode. While flashing, quickly press any button on
the remote control to pair. If this does not work, please try the steps above
again.
Remote Control De-pairing: While charging when the product is turned off,
please complete the following steps within 10 seconds: quickly rotate the
right rotary knob clockwise by 4 positions, counterclockwise by 4 positions,
and then clockwise once again by 4 positions. The light will flash quickly for
10 seconds to signal that the de-pairing is successful.
WARRANTY
Within 30 days of purchase: Contact the original seller for repair or
replacement.
Within 2 years of purchase: Contact Olight for repair or replacement.
This warranty does not cover normal wear and tear, modifications, misuse,
disintegrations, negligence, accidents, improper maintenance, or repair by
anyone other than an authorized retailer or Olight itself.
USA Customer Support: [email protected]
Global Customer Support: c[email protected]
Visit www.olightworld.com to see our complete
product line of portable illumination tools.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following twO conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver. Connect the
equipment into an outlet on a circuit diferent from that to which the receiver
is connected. Consult the dealer or an experienced radio/TV technician for
help.
RF Warning Statement
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction,
IC STATEMENT
This device complies with Industry Canada licenceexempt RSS standard(s).
Operation is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.