REMORAN WAVE 3 300W Hydrogenerator Instruction Manual

REMORAN WAVE 3 300W Hydrogenerator

Read the entire operating instructions carefully before using the hydro generator. The instructions can be found on our website: www.remoran.eu

Connection illustration

1. Install the rail on the boat
2. Attach the turbine to the outboard unit
3. Install the charger in a dry place
4. Drill the feedthrough for the cable and install the connectors
5. Install the generator cable to the charger
6. Install the charging cables in the charger (Be sure to install a fuse and a ferrite filter)

Outboard unit and charger components

Outboard unit components

1. Angle adjustment knob
2. Angle guide
3. Locking handle
4. Frame
5. Generator cable
6. Telescopic blade
7. Locking pin and cotter
8. Generator
9. Turbine

Charger components

1. Cooling profile
2. Charging wire (pos.)
3. Charging wire (neg.)
4. Screw terminals of the generator wires
5. Bluetooth® wireless connection indicator
6. Charger’s LED indicator
7. Plastic cover
8. Fastening slots (4 pcs)

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Remoran Oy is under license.

Rail installation

1. Mounting parts
2. Mark the locations of the holes
3. Drill the holes Ø 8 mm
4. Slide the bolts into place
5. Add Sealant
6. Place the rubber mat on the rail
7. Insert the rail
8. Apply sealant around the bolts on the inside
9. Place the reinforcement plate, rubber washers, washers and nuts on top of the bolts and tighten

Mounting the turbine

1. Slide the turbine onto the shaft
2. Insert the screw and washers and tighten
3. When the turbine has been installed correctly, there is a gap of ~3mm between the turbine and the generator

Charger installation

1. Select the lenght of the screws according to the thickness of the base
2. Mark the location of the charger in a dry place with the help of the included stencil
3. Screw on the charger. Space must be left around the charger for cooling

Installing the cable feedthrough

1. A feedthrough is made to the transom of the boat for the connector (1)
2. Drill a hole for the connector in the transom
3. Insert the cable through the hole and insulate the feedthrough with sealant
4. Fasten the connector with two wood screws

Connecting the cables

1. The numbered wires should be connected to the corresponding numbered screw terminals of the generator connection of the charger
2. Carefully connect the charging wires to the appropriate apertures with the + and – wires in their appropriate locations

Adjustments before operation

1. Detach the locking pin cotter and pull out the pin to adjust the blade to a suitable height
2. Lock the blade by securing the pin and locking pin cotter back in place
3. We recommend to use a safety rope
4. Do not tie the safety rope to the locking handle

Attaching the outdoor unit to the rail

1. Lift the locking handle to the top position
2. Slide the outboard unit down the frame along the rail
3. Lock the outboard unit to the rail by pushing the handle down to the bottom position
4. To adjust the angle, first press the angle adjustment knob so that its bottom rises.
5. Then slide the knob along the angle guide to a desired position
6. The angle of the outboad unit should be perpendicular to the surface of the water
7. Connect the cable connector to the feedthrough connector installed in the boat
8. The device is ready for use! Charging starts automatically when the turbine starts rotating

Charger installation guide

Scale

Remoran Oy

• Harventajankuja 3, FI-24130 Salo, Finland
• www.remoran.eu
• info@remoran.eu

References

• Remoran - Green Energy Boating

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>