REMORAN 3GD Green Energy Boating Rail Instruction Manual

Table of Contents

Installation Instructions:

Install the generator cable to the charger.
Install the charging cables in the charger. Be sure to install a fuse and a ferrite filter.
Place the rubber mat on the rail.
Insert the rail.
Apply sealant around the bolts on the inside.
When the turbine has been installed correctly, there should be a gap of approximately 3mm between the turbine and generator.
Select the length of the screws according to the thickness of the base.
Mark the location of the charger in a dry place with the help of the included stencil.
Screw on the charger, leaving space around it for cooling.
Create a feedthrough to the transom of the boat for the connector.
Insert the cable through the hole and insulate the feedthrough with sealant.
Fasten the connector with two wood screws.

Connecting the Cables:

Make sure the cables have the correct polarities (+, -). Incorrect installation may cause breakage of the charging unit.

The numbered wires should be connected to the corresponding numbered screw terminals of the generator connection of the charger.
Carefully connect the charging wires to the appropriate apertures with the ledarna dras till de erforderliga positionerna.

Blade Adjustment:

Detach the locking pin cotter and pull out the pin to adjust the blade to a suitable height.
Lock the blade by securing the pin and locking pin cotter back in place.

Outboard Unit Installation:

Slide the outboard unit down the frame along the rail.
Lock the outboard unit to the rail by pushing the handle down to the bottom position.
To adjust the angle, press the angle adjustment knob so that its bottom rises.
Slide the knob along the angle guide to a desired position.
The angle of the outboard unit should be perpendicular to the surface of the water.

Boat Connection:

Connect the cable connector to the feedthrough connector installed in the boat.

EN Read the entire operating instructions carefully before using the hydrogenerator. The instructions can be found on our website: www.remoran.eu

EN 1. Install the rail on the boat
EN 2. Attach the turbine to the outboard unit
EN 3. Install the charger in a dry place
EN 4. Drill the feedthrough for the cable and install the connectors
EN 5. Install the generator cable to the charger
6. Install the charging cables in the charger (Be sure to install a fuse and a ferrite filter)

Outboard unit components

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Remoran Oy is under license.

Mounting parts
Mark the locations of the holes
Drill the holes Ø 8 mm
Slide the bolts into place
Place the rubber mat on the rail
Place the rubber mat on the rail
Insert the rail
Apply sealant around the bolts on the inside
Place the reinforcement plate, rubber washers, washers and nuts on top of the bolts and tighten

Slide the turbine onto the shaft
Insert the screw and washers and tighten
When the turbine has been installed correctly, there is a gap of ~3mm between the turbine and generator
Select the lenght of the screws according to the thickness of the base
Mark the location of the charger in a dry place with the help of the included stencil
Screw on the charger. Space must be left around the charger for cooling

The numbered wires should be connected to the corresponding numbered screw terminals of the generator connection of the charger

Carefully connect the charging wires to the appropriate apertures with the + and – wires in their appropriate locationsAdjustments before operation

Detach the locking pin cotter and pull out the pin to adjust the blade to a suitable height
Lock the blade by securing the pin and locking pin cotter back in place
We recommend to use a safety rope
Do not tie the safety rope to the locking handle

Attaching the outboard unit to the rail

Lift the locking handle to the top position
Slide the outboard unit down the frame along the rail
Lock the outboard unit to the rail by pushing the handle down to the bottom position
To adjust the angle, first press the angle adjustment knob so that its bottom rises.
Then slide the knob along the angle guide to a desired position
The angle of the outboard unit should be perpendicular to the surface of the water
Connect the cable connector to the feedthrough connector installed in the boat
The device is ready for use! Charging starts automatically when the turbine starts rotating

Charger installation guide