mistral MDB-30F09 75cm Commercial Mist Fan Instruction Manual

mistral MDB-30F09 75cm Commercial Mist Fan

Important Safeguards

When using electrical appliances, in order to reduce the risk of fire, electric shock and/or injury, these basic safety precautions should always be followed:

For Your Safety

Read all instructions carefully, even if you are familiar with the appliance.

• To protect against the risk of electric shock, DO NOT IMMERSE power cord or plug in water or any other liquid.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory and mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• Always unplug the unit when not in use.
• Do not operate unit with a damaged power cord or plug, or after a malfunction, has been dropped or is damaged in any manner. Return the unit to an authorized service facility for examination.
• Do not run the power cord under carpeting or cover the power cord with throw rugs, runners or the like. Arrange the power cord away from traffic areas and where it will not be tripped over.
• Do not place the power cord over any part of the unit.
• Do not plug this unit into an extension lead, double adapter or power board.
• This unit has hot electrical parts inside. DO NOT use it in areas where gasoline, paint or flammable liquids are used or stored.
• To disconnect the unit set main switch to OFF then remove the plug from the outlet.
• DO NOT use it in areas where gasoline, paint or flammable liquids are used or stored.
• Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock, fire or could damage the unit.
• Use the unit only as described in this booklet Any other use not recommended by the manufacturer may cause fire, electric shock or injury to persons.
• Fully remove the power cord from the power cord tidy before use. Always uncoil the power cord before applying power.
• This product must always be used AND STORED in the upright position.
• Do not use this unit with a programmer, timer or any other device that switches the unit on automatically, since a fire risk exists if the unit is covered or positioned incorrectly.
• This appliance is suitable for outdoor use.
• If it is necessary to move the unit after the water has been added, roll gently to the required position.
• Do not move the machine when it is in use.
• Always ensure that there is enough water in the tank when in use for cooling.
• Do not block air circulation.
• Do not use hot water.
• Place the machine on a level surface.
• Unplug the appliance during filling and cleaning.

Warning
If the supply power cord is damaged, the power cord must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

This product has not been designed for any uses other than those specified in this booklet.
Save These Instructions

Features of Your Misting Fan

Your 75cm Commercial Mist Fan

Congratulations on the purchase of your new Commercial Mist Fan.
Before first using your Commercial Mist Fan it is most important that you read and follow the instructions in this use and care booklet, even if you feel you are quite familiar with this type of appliance.
Your attention is drawn particularly to the section dealing with IMPORTANT SAFEGUARDS. Find
a place and keep this booklet handy for future reference.
Your Commercial Mist Fan is safe and easy to use. It has been designed to function quietly and safely under normal circumstances.

Assembly of Your Misting Fan

Your Misting Fan has been boxed unassembled to minimize packaging waste. Each part is designed to fit together and be disassembled easily for cleaning or storage.

Accessory list

Tips:
Because the mist fan is heavy, so when assembling, it may require additional people to assist.
Carefully remove the Mist fan & accessories from the plasticbag and carton. And taking out the mist fan, please handle with care in order to avoid the damage of product.
Place the Mist fan & accessories on a soft cloth or carpet (To avoid causing any damage during assembly of the support tube).

Step 1: Assembling cart

1. Fit rear wheels to the cart
   Insert plastic washer(12 MM Dia.) and axle onto to the round tube on either side of the cart, position the wheels on the axles and secure wheels with M12 Washer and M12 nuts.

2. Fit 2 casters to the front of the cart.
   Use 4 M6 and M6 Screws for each caster and tighten to secure.

3. Fit the pillar to the cart base and secure with 4 M6 x 20mm screws.

Step 2: Install fan head mounting post
Loosen post retention knob (A) on the pillar, insert Stainless Steel tube(B) and switch control box into pillar and fasten with retention knob to secure in place.

Step 3: Mounting fan motor assembly
Unscrew the 3 screws on the motor support collar and position the fan motor assembly onto the post protruding from the switch control box and tighten the 3 screws to secure the fan motor assembly (see Fig.3)

Fig3

Step 4: Fitting the rear safety grille.
Unscrew and remove the 4 grille retaining screws from the fan motor head assembly.
Position the rear safety grille on the fan motor head and align the holes on the grille with screw holes on the fan motor head and secure the grille with the 4 screws.( See Fig.4)

Fig4

Step 5: Fitting the fan blade
Position the blade onto the motor shaft and secure by tightening the blade retention screw.(see Fig. 5)

Step 6: Fitting misting plate to front safety grille.
Unscrew and remove the 4 retaining screws from the mist plate assembly.
Position the mist plate onto the front safety grille and secure it to the safety grille with 4 screws and tighten. (see Fig. 6)

Step 7: Fitting front safety grille/mist plate assembly to the rear safety grille.
Unhinge the grille retaining clips from around the front safety grille parameter.
Clip the retaining bracket over the rear grille and hinge the retaining clips to the closed position to capture the rim of the rear safety grille with the hinge clips until all closed.
Finally secure grille into place with the safety screw and nut on the bottom of grille assembly. (See Fig.7)

Step 8: Fitting water tank to the cart
Fix water tank on the cart-shelf with nominated screws and nuts (Fig8)

1. Tip fan assembly slowly backwards to lay on the floor to gain access to the screw holes on the bottom of the cart tank shelf.
2. Secure the tank to the cart-shelf with 4 x M8 washers and M8 x 10mm screws and tighten them with a spanner.
3. Position the fan assembly upright.

Note: If you do not use mist fan for a long time, please unscrew the drain hole at the bottom of the water tank,and when the water is drained, tighten it again.

Operation

1. After assembly this misting fan, before connect to power supply, need remove the protection red wires from the grilles;

2. Open water tank cover, pour enough clean water into tank then cover it;

3. Connect power supply, turn on fan switch first(this switch is underneath the protection cover), then turn on pump switch, the misting volume could be adjusted according to the misting volume indication.

4. Three speed for the fan setting, 0 for off, 1 for Low, 2 for Medium and 3 for High.

5. Adjustable Mist amount Increase or decrease the amount of mist by turning the mist adjusting dial until desired intensity is reached.

Oscillation Setting

To incorporate the oscillating operation into the Misting fan you need to secure the oscillating actuator arm to the mounting hole at the edge of the oscillating rotor disc and secure with washer and adjustment screw.
Note: To operate misting fan without Oscillation, connect and secure actuator arm to the center mounting hole of the rotor disc.

Fan height adjustable

Unscrew A and then extend draw tube to adjust the height of mist fan.

Care and Cleaning

To clean: Disconnect the power cord from the mains. Remove the Front Guard and the blades carefully. Do not drop the blades! First use a soft cloth with light soap to clean off oil stains, then wipe thoroughly with a dry cloth. Never use polish or any corrosive liquid that will damage the paint, metal or plastic! Replace the blades and lock the guard securely before use.

• Never spray with liquids or submerge the Misting Fan in water or any other liquid.
• Do not fill the water tank with water over 45°C, to avoid discoloration or deformation.
• When ambient temperature is near or below 0°C, remove all water from in and around the tank to prevent ice forming, which could damage components.
• Do not fill water anywhere other than the water tank. Mop up any spills immediately.

WARNING: Unplug from electrical supply source before cleaning or filling / emptying the water tank. After servicing, any safety device (including grilles and blades) must be reinstalled or remounted as previously installed.

Technical Specifications

Note: As a result of continual improvements, the design and specifications of the product within may differ slightly to the unit illustrated on the packaging.

DISPOSAL

Do not dispose of packaging or the product through your household waste! The product and packaging are made from recyclable materials (plastics, metals, paper).
If the product is no longer suitable for use dispose of it in an environmentally friendly manner in accordance with your local council.

Warranty Conditions For  Purchase In Australia

Any claim under this warranty must be made within 2 years of the date of purchase of the product.
To make a claim under the warranty in Australia, take the product (with proof of purchase) to Place of Purchase.
GSM Retail Group bears reasonable, direct, expenses of claiming under the warranty in Australia. You maybe requested to submit details and proof to outlet for consideration or contact Consumer Service Centre phone number below.
This warranty is provided in addition to other rights and remedies you may have under law: our goods come with guarantees which cannot be excluded under the Australian Consumer Law (if purchased in Australia). You are entitled to replacement or refund for a major failure and to compensation for other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
The warranty excludes damage resulting from product misuse or product neglect. The warranty covers domestic use only and does not apply to commercial applications.
This warranty is given by GSM Retail Group
ABN: 53007682475
For Warranty and technical queries 1300 941 901

Warranty Exclusions

Damage to the appliance or any part through accident, misuse or negligence.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>