TOUCHBeauty TB-1733 Manicure and Pedicure Kit Instruction Manual

TOUCHBeauty TB-1733 Manicure and Pedicure Kit Instruction Manual

Safety Instructions

To ensure proper operation of this device, please read this instruction manual carefully before using the device and keep it for further reference.

WARNING

• The following persons should not use this device: children; persons with skin inflammation on the fingers or toes; persons with allergies; persons with reduced physical, sensory or mental skills; persons with diabetes.
• If you feel uncomfortable while using the device, please stop using it and consult a doctor.
• Do not use this device for any other purpose than nail care.
• Do not attempt to modify, disassemble, or repair the device by yourself.

CAUTION

**** This device has a lithium battery. Do not place or store the device for long periods under a hot or humid environment. If you do not intend to use the device for a long time, store it after it is fully charged.

Device Specifications

• Name: 6 in 1 Electric Manicure/Pedicure Set
• Model No.: TB-1733
• Input: 5V /330mA
• Power: 3.7V /2.3W
• Type of Battery: Li-ion 3.7V 800mAh
• Executive Standard: Q/XM1006-2020

Device Description

1. Emery Head (coarse 100#
2. Emery Head (fine 120#)
3. Chrome Head
4. Needle Emery Head 07
5. Tungsten Steel Head
6. Felt Cone Head 06
7. +/-Buttons
8. Power Button
9. Charging Port
10. USB Cable
11. Accessories Storage Box

Preparation Instructions

• Charging the device: Connect the USB cable to the device charging port and to the charging adapter to charge. The indicator flashes a red light while the device is charging and turns blue when the battery is full.
• When the battery is low, the power button flashes a red light. Before it turns off, the power button will flash 3 times a red light, and automatically shuts down.
• Charging the device takes approximately 3.5 hours. When the battery is fully charged, the device can be used consecutively for about 60 minutes

How to Use

To ensure the correct operation of this device, please read the instructions carefully before use.

1. Open the accessories storage box. **(Picture 2)

**

2. It is recommended to select the head from coarse to fine. To install the head, push it into the device until it is securely in place.

   • Emery Head (Coarse): Suitable to repair natural nails; can be used to grind the front edge and the sides of acrylic nails. (Picture 3)
     

   • Emery Head (Fine): Suitable to repair natural nails; can be used to grind the front edge and the sides of acrylic nails. (Picture 4)
     

   • Chrome Head: Suitable to grind and polish around the cuticles and surface of natural and acrylic nails. Smooths and shapes the nails. **(Picture 5)

**

  * Needle Emery Head: Suitable to clean away hard skin on the side of the nails. **(Picture 6)

**

  * Felt Cone Head: Suitable to clean the nail surface, brightens and smooths the nail. **(Picture 7)  

**

  * Tungsten Steel Head: Removes gel nail polish from the nails. **(Picture 8)  

**

3. After you install the accessory head, press and hold the power button for around 1.5 seconds. The power button lights up white, and the device turns on . (Picture 9)
   

4. To Switch the rotation direction: short press the power button to change the rotation direction. **(Picture 10)

**

5. To increase the speed.

   • Press and hold the + button to adjust the speed continuously. The + button light flickers white. When you reach the maximum speed, the + button indicator light stops flickering.
   • Short press the + button each time you want to increase the speed. Each time you increase the speed, the + button light
     indicator flickers one time white. After reaching the highest speed level, the indicator light stops flickering. The speed can be adjusted up to 8 times.

6. To decrease the speed.

   • Press and hold the – button to adjust the speed continuously. The – button lights up intermittently white. When you reach the lowest speed, the – button indicator light stops flickering.
   • Short press the – button each time you want to decrease the speed. Each time you decrease the speed, the – button light indicator flickers one time white. After reaching the lowest speed level the indicator light stops flickering. The speed can be adjusted up to 8 times.

7. After use, press and hold the power button for a few seconds until the device shuts down. After cleaning the heads, store them in the storage case.

Cleaning & Maintenance

1. Make sure the device is power off before you start cleaning.
2. Do not immerse the device in water. The head accessories can be cleaned separately.
3. Clean the surface of the device with a slightlywet cloth before and after each use.
4. Do not use lubricants, detergents, polishing agents, or air fresheners on this device.

Storage

Storage: This device has a lithium battery. Do not place or store the device for long periods under a hot or humid environment. If you do not intend to use the device for a long time, store it after.

Recycling

The built-in battery contains substances that may pollute the environment. When disposing of this device, do not put it in the general household waste. Please dispose of this device in an official recycling point to contribute to environmental protection.

Warranty & Support

Troubleshooting

grinding head correctly as guided.
The device does not work.| The battery is low.| Charge the device as guided.
The battery is out of power.
The charging indicator does not light up.| The USB cable is not properly connected.| Plug the USB cable correctly into the device charging port and charging adapter.
The head is in an eccentric position.| The head was not installed correctly.| Install the head correctly as guided.
The head easily falls down.
Other problems.| | Please consult your local retailer.

Note: If the device still does not work properly after using the above solutions, please stop using the device and contact your local retailer.

After-Sales Service

Please visit our website www.touchbeauty.com or contact our customer service team customer@touchbeauty.com if you need to learn about our products or if you need any information. You can also contact an affiliate dealer in your country.

MANUFACTURER: TOUCHBEAUTY BEAUTY & HEALTH (SHENZHEN) CO., LTD
ADDRESS: 601 & 602, Block F5, TCL International E-City, 1001 Zhongshanyuan Road, Shogun Community, Xilinx Sub district, Nanshan District, Shenzhen, China.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>