Lucid AUDIO 812944027650 Hearing Aid Sanitizer and Dryer with Battery Tester Owner’s Manual

: June 3, 2024
: Lucid Audio

Table of Contents

Overview
Technical Specifications
Keys Overview
Functions
Operation
NOTES
Support
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Lucid AUDIO 812944027650 Hearing Aid Sanitizer and Dryer with Battery Tester Owner’s Manual

Overview

Hearing aids are electronic devices of high precision and their requirements of use should be strictly observed. Due to the sweat and humidity encountered in daily use, it is especially important to perform daily maintenance.

Keeping your hearing aids clean is important. Sweat and earwax built up on hearing aids might allow bacteria to breed, as well as affect the unit’s performance.

Hearing aids consume battery life. When a battery gets low, weak or intermittent, distorted output or a dead unit can occur. Leakage from batteries will damage the hearing aids.

The Lucid Audio Sanitizer Dryer is our latest design with three integrated multi-functions –

The machine dries and dehumidifies the hearing aids with its heating and thermostat function. To kill the bacteria, UV/ LED generates 275nm ultraviolet light in sterilizing and disinfecting mode. The battery monitoring function indicates the level of battery remaining to remind users to change batteries on time.

Technical Specifications

Environment:
- Surrounding environment temperature: 5 ‘C- 40 ‘C
- Air humidity: <80%RH ( when temperature is 25 ‘C )
- No inflammable corrosive gas or conductive dust should exist in the air
Power:
- Voltage: DCS.OV
- Current: DC 2.0A
- Power: < 5W
Automatic temperature control: SO ‘C±S ‘C
Timer Control:
- Selectable drying time settings for 3, 6, 9 hours
- Sterilization time: 30 minutes
UV LED specturm: 275nm
Battery Indicator: three levels
- Green light – battery power• 1.30V
- Yellow light – battery power• 1.1 SV but < 1.30V
- Red I ig ht – battery power < 1.1 SV
Safety protection:
- Over-temperature & over-heating protection
- Protection against UV/LED leaking

Keys Overview

Functions

Constant heating
Set the thermostat control at S0’C ±S’C to keep the unit(s) drying. The circuit board of the machine consists of 24 pieces of crystal heating elements set in an intensive array and fixed to the PCB. These heating points make sure the machine is heated in a balanced manor.
Sterilization
The machine contains a UV LED tube which generates 275 nm UV.
The high intensive UV/LED illuminates at a short distance to kill
surface bacteria and viruses.
The drying environment can restrain the bacteria growth during constant heating. With the effect of integrated functions, the dryer has extremely efficient sterilization function.
There are no side-effects such as pollution or damage to hearing aids. Operation of the unit is easy, convenient, safe and environmentally friendly.
Three-level battery indication
- Green light – battery power greater than 1.30v. Battery Full/Strong.
- Yellow light – battery power greater than 1.1 Sv but less than 1.30v.
  Battery nee~s to be replaced soon.
- Red light – battery power less than 1.1 Sv. Battery is exausted and
  should be replaced immediately.
Safety protectron
- Over-temperature & over-heating protection
  When the surface temperature of heating unit is over the limited temperature, the protective mechanism will automatically cut the circuit board off for safety. When the surface temperature of the heating part is below the limit of 80’C, the mechanism will restart the unit automatically.
- Protection against UV/ LED leaking
- When the upper cover is not closed properly, the device will
  not run.
- During sterilization, the protective mechanism will cut off the
  power whenever the cover is opened. The UV/LED tube will be turned off immediately to avoid any hurting of the eyes or skin by light leakage.When the cover is closed, the unit will continue working once again.
Main control unit
The SCM technology will collect all of the data and distribute it to the CPU.

Operation

Placement: Remove the battery from the unit. Open the cover of the Sanitizer Dryer and place the hearing aid(s) in the center position. Close the cover.

Power connection: connect the power chord from the adapter to the Sanitizer Dryer. The power unit will turn on when connected properly.

Timing and running: Press the timer key to select 3h, 6h or 9h. The indicator light will reflect your choice. At this time, the sterilization and disinfecting function will run automatically for 30 minutes.

End of cycle: The unit will stop heating automatically when the setting time is reached. The indicator lamp will begin blinking at that point. The drying process will be finished and the hearing aid(s) should be removed from the machine.

Constant heating: Press the timer key to start heating constantly.
The sterilization and disinfection functions will work simultaneously.
The sterilization and disinfection function can be turned off by manually pressing the sterilization key.

Sterilizing & disinfecting: The indicator lamp will light up after connecting with the power. Press the sterilization key to sterilize and disinfect. The unit will stop automatically after 30 minutes of runtime.

Battery Tester: All kinds of zinc air batteries for hearing aid use can be tested by this machine. Place battery in the test slot; the power remaining in the battery will trigger the correct light to activate.

NOTES

Remove hearing aid battery prior to use.
Make sure the hearing aids are clean without battery leakage prior to using the dryer.
Power specifications must be strictly observed with the instructions to avoid serious consequences, such as halting operations or burning out the machine.
Do not cover the machine while it is working.
The drying time must not exceed 12 hours in a day.
Please pull out the plug after drying.
Do not try to disassemble or repair the unit.
Keep away from children.