INKBIRD IRS-WD1 Water Leak Sensor User Manual

WATER LEAK SENSOR
IRS-WD1 Water Leak Sensor
User Manual

Product Introduction

This smart water sensor is a device that can detect water leak and submersion, and monitor the two states of no water inflow to water inflow and water inflow t o retreat. It will send us a real-time notification message through the INKBIRD app when there i s water leakage or submersion. This product should be used with a device that features the function of gateway IBS-M2.
Short press the action button to transmit data t o the gateway once, and the indicator will light up once, I f the gateway successfully receives the data, the buzzer will alarm once t o verify the effective distance of wireless communication.

Specification

APP Connection

3 . 1 Add The Device
a.Follow the gateway’s user manual t o add the gateway (IBS-M2) to the app.
b . Install the batteries for the water leak sensor (transmitter) and confirm thatit works properly. T h e n put it as close as possible t o the gateway (IBS-M2).
c.Open the app and go t o the gateway device page. Click the “+” in the upper right corner t o enter the “Add Device” page and follow the prompts t o continue.

I f adding the device fails, move the device close to the gateway and repeat steps atoc.
3.2 Installation Guide

• Place the device directly on the surface t o be monitored.
• Verify the effective distance: Press the action button of the device placed on the preselected installation locaion . The gateway will emit a tone, indicating that the device can effectively communicate with the gateway.
• ensure stable wireless communication, do NOT install the device on any metal surface.

Safegu ards

• Please do not disassemble the product if you are not a professional.
• Be sure that the sensor i s not covered with dust as dust may lead to inaccurate measurements.
• Do not use alcohol t o clean the sensor.

Product Warranty

This i t e m carries a 1-year warranty against defects in either components or workmanship. During this period, products that prove t o b e defective will, at the discretion of INKBIRD, be either repaired or replaced without charge.

FCC Requirement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority t o operate the equipment. This device complies with Part 15 of the FCC Rules. Operation i s subject t o the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant t o Part 15 of the FCC Rules. These limits are designed t o provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference t o radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference t o radio or television reception , which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

— Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be c o – located or operating in conjunction with any other antenna or transmitter.

INKBIRD TECH.C.L
support@inkbird.com
Factory address: 6th Floor, Building 713, Pengji Liantang Industrial
Area, NO.2 Pengxing Road, Luohu District, Shenzhen, China
Office address: Room 1803, Guowei Building, NO.68 Guowei Road,
Xianhu Community, Liantang, Luohu District, Shenzhen, China

Documents / Resources

| INKBIRD IRS-WD1 Water Leak Sensor [pdf] User Manual
IRSWD1, 2AYZD-IRSWD1, 2AYZDIRSWD1, IRS-WD1 Water Leak Sensor, IRS-WD1, Water Leak Sensor, Leak Sensor, Sensor
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>