INKBIRD IHC-200-WIFI Humidity Controller User Manual
- June 3, 2024
- INKBIRD
Table of Contents
IHC-200-WIFI Humidity Controller
User Manual
IHC-200-WIFI
Humidity Controller
Introduction
① PV: In the normal mode, it displays current humidity; in the setting mode,
it displays menu code.
② SV: In the normal mode, it displays the setting humidity value; in the
setting mode, it displays the setting value.
③ Red Indicator Light: The indicator light will turn red when the
humidification output is on and the indicator light will turn off when the
humidification output is off.
④/⑤ Green Indicator Light: The indicator light will turn green when the
dehumidification output is on and the indicator light will turn off when the
humidification output is off. If the green indicator light blinks, the device
is in the mode of dehumidification delay protection state and the
humidification output is off.
⑥ WORK1: Humidification Output Socket.
⑦ WORK2: Dehumidification Output Socket.
⑧ Setting Button( ), Increase Button( ),
Decrease Button( ): More details on Settings.
Product Features
- Plug-n-Play
- Dual Relay Output: Support both humidifying equipment and dehumidifying equipment at the same time.
- Display Screens: Display set humidity value and the measured humidity value at the same time.
- Support Humidity Calibration
- Support Dehumidification Control Delay Protection
- Settable High/Low Humidity Alarm
- Probe Fault Alarm
- Wi-Fi Smart App
Specifications
- Voltage: 100-230Vac 50/60 Hz
- Current: 10A
- Maximum Power: 1200W(120Vac), 2200W(220Vac)
- Humidity Measurement Range:10r%d99%RH
- Humidity Display Accuracy: 0.1 %RH
- Relative Humidity Accuracy(10% to 95%RH): Typ: ±3%RH, Max: ±5%RH
- Display Unit: %RH
- Operating Ambient Temperature: -20°C~40°C/-4°Frw1 04°F
- Storage Temperature: 0℃~60℃/32℉~140℉
- Storage Humidity: 20~80%RH (not frozen or dewed)
- Warranty:
Controller: 2 years
Probe: 1 year
Wi-Fi Connection
4.1 Download INKBIRD App
Search the keyword “INKBIRD” in Appstore or Google Play to get the app, or you
can scan the following QR code directly to download and install the
app.
https://inkbird.com/pages/app-download
Scan QR code to download
INKBIRD APP
4.2 Connect to your phone
① Register before using the INKBIRD app. Select your Country/Region, enter
your e-mail, then a verification code will be sent to your mailbox, enter it
to confirm your identity and the registration is done.
② Then press “Add Home ”button to create your home.
(3) Tap “+” or “add device” button in home page of the APP to add the device.
(4) Press and hold the button for 2 seconds to reset the WIFI when the
controller is under normal working state. The controller will enter the
Smartconfig configuration state by default. You can short press the button to
switch between the Smartconfig configuration mode and the AP mode.
As the WIFI module need time for data processing, so it will take about 5
seconds to display the corresponding LED symbol and state if the Wi-Fi states
change.
4.3 Quick Connection
(1) Plug the device in the socket and make sure that the device is in the
Smartconfig state(the LED symbol is flashing rapidly, interval flashing
250ms).
(2) Check if the LED symbol is blinking rapidly and confirm on your app if it
is, then enter your Wi-Fi password to connect to wireless network, click
Confirm to connect the device.
Note: The device only supports 2.4GHz Wi-Fi router.
4.4 Connect the device in AP mode
① Plug the device in the socket and make sure that the device is in the AP
Configuration State(the LED symbol is flashing slowly, interval flashing
1500ms).
② Click “Confirm indicator slowly blink” and then select Wi-Fi network, enter
Wi-Fi password, click “Confirm” to enter connection process.
③ Press “Connect now” and it will go to your WLAN Setting interface on your
smart phone, select the “SmartLife-XXXX” to directly connect to the router
without putting in password.
④ Go back to the app to enter into the automatic connection interface.
connection process.
⑤
Click “Done” after adding device successfully and enter into the device
controlling interface.
⑥ In the humidity control mode, users can do some control function settings
with the app.
4.5 Wi-Fi State
- Smartconfig State: The Wi-Fi indicator light is flashing rapidly, interval flashing 250ms.
- AP State: The Wi-Fi indicator light is flashing slowly interval flashing 1500ms.
- Connection Fail State: The Wi-Fi indicator light turns off.
- Connection Succeed State: The Wi-Fi indicator light keeps on.
Settings
5.1 Key Setting
5.1.1 Factory Reset
Hold the button and turn on the device, the buzzer will beep shortly to remind
the users that all parameters of the the humidity probe are restored to
factory settings.
5.1.2 Fast Setting
Press the button lightly to enter quick Press the button lightly to enter
quick set-up mode and set the value, the SV screen will display the current
setting value and keep flashing. Press the button or the button to change the
value, hold the button or the button to change the value quickly, press the
button again to save settings and quit the setting mode, the controller will
also save settings and quit the setting mode if there is no operation for 10
seconds.
5.1.3 Normal Setting
Hold the button for 2 seconds to enter setting mode when the controller
working normally, the PV screen will display the code “HS” of the first menu
item and the SV screen will display the corresponding setting value. Press the
button to switch between menu items, press the button or the button to change
the value, the value will be saved automatically when you switch to another
menu item by pressing the button.
Press and hold the button for 2 seconds to save settings and quit the setting
mode, the controller will also quit the setting mode and turn to normal
working mode if there’s no operation for 30 seconds.
5.2 Flowchart of the Settings
5.3 Icons in this Manual
Symbol| Icon| Function| Setting Range| factory
Settings| Note
---|---|---|---|---|---
HS| | Humidity Setting Value| 5.0%RH ~99.0%RH| 50.0%RH| See 6.1
HD| | Humidification Difference Value| 1.0%RH ~20.0%RH| 5.0%RH
DD| | Dehumidification Difference Value| 1.0%RH ~20.0%RH| 5.0%RH
AH| | Alarm High Humidity Limit| 5.0%RH ~99.0%RH| 99.0%RH| See 6.2
AL| | Alarm Low Humidity Limit| 5.0%RH ~99.0%RH| 5.0%RH
PT| | Dehumidification Delay Time| 0~10 Minutes| 0 Minute| See 6.3
CA| ****| Humidity Calibration| -20.0%RH ~20.0%RH| 0.0%RH| See 6.4
Basic Operations
6.1 Instructions for Humidity Control Setting(HS,HD,DD)
The PV Screen displays the measured value of current humidity when working
normally, recognize and switch between humidification mode and
dehumidification mode automatically. If the measured Humidity(PV) 5 Humidity
Setting Value(HS)-Humidification Differential Value(HD), the equipment will
enter humidification state, the red led is on, WORK1 output socket turns on.
If the measured Humidity(PV) ? Humidity Setting Value(HS), the red led is off,
WORK1 output socket turns off.
If the measured Humidity(PV) ? Humidity Setting Value(HS)+Dehumidification
Differential Value(DD), the equipment will enter dehumidification state, the
green led is on, WORK2 output socket turns on. If the green led is blinking,
indicating that the dehumidification device is in the state of the
dehumidification delay protection, WORK2 output socket turns off. If the
measured Humidity(PV) 5 Humidity Setting Value(HS), the green led is off,
WORK2 output socket turns off.
Example: HS=50.0%RH, HD=5.0%RH, DD=8.0%RH, If PV(the measured humidity) ?
58.0%RH(HS+DD), the equipment will enter the dehumidification state, the green
led is on, WORK2 output socket turns on. If PV 55.0%RH(HS), the green led is
off, WORK2 output socket turns off. If PV 5 45.0%RH (HS-HD), the equipment
will enter the humidification state, the red led is on, WORK1 output socket
turns on. If PV a 50.0%RH(HS), the red led is off, WORK1 output socket turns
off.
Note: There is no need to judge the differential value of humidification
or dehumidification when power on or exiting the setting state. For example:
when power on or exiting the setting state HS=50.0%RH, HD=5.0%RH, DD=8.0%RH.
If PV(the measured humidity) > 50.0%RH(HS), it will enter the dehumidification
state. When PV 5 50.0%RH(HS), the dehumidification stops, then return to
normal humidity control mode. If PV < 50.0%RH, it will enter the
humidification state. When PV ≥ 50.0%RH,the humidification stops, then return
to normal humidity control mode.
6.2 High/Low Humidity Alarm(AH,AL)
The equipment will alarm if the value of measured humidity(PV) ? the set value
of high humidity alarm(AH), the PV screen will display the set value of high
humidity alarm(AH) and the current humidity value alternately, the buzzer will
alarm like “bi-bi-Biii”until the value of measured humidity(PV) < the set
value of high humidity alarm(AH). You can also stop the alarming by pressing
any button of the equipment.
The equipment will alarm if the value of measured humidity(PV) 5 the set value
of Low humidity alarm(AL), the PV screen will display the set value of low
humidity alarm(AL) and the current humidity value alternately, the buzzer will
alarm like “bi-bi-Biii” until the value of measured humidity(PV) > the set
value of low humidity alarm(AL). You can also stop the alarming by pressing
any button of the equipment.
Note: The setting value of low humidity alarm(AL) should be less than the
setting value of high humidity alarm(AH).
6.3 Dehumidification Delay Time(PT)
The equipment will not start immediately in the mode of dehumidification for
the first time if the measured value is larger than the sum value of set
humidity value and dehumification return difference, the equipment will start
to dehumidify after the set delay time. The equipment will dehumidify
immediately if the interval time of two adjacent dehumidification is longer
than the delay time. The equipment will dehumidify after delay time if the
interval time of two adjacent dehumidification is shorter than the delay time.
The delay time start timing when last dehumidification is done.
Note: There is no need to judge the delay time when power on or exiting
the setting state.
6.4 Humidity Calibration(CA)
If the measured humidity differs from the standard humidity, you can calibrate
the device by adding or reducing the correction value to align the measured
humidity to the standard humidity.The calibrated humidity = the measured
humidity value + the calibration value.
Sensor Fault Alarm
If the humidity sensor is in circumstances of short circuit or open circuit, the controller will enter probe fault mode and stop running, the buzzer will alarm and the screen will display ER. You can press any key to stop the buzzer and the controller will back to normal working state when all malfunctions are resolved.
Important Safeguards
It’s important that you take special care when using electrical appliances. Follow our tips to stay safe.
- Read all instructions.
- Check that flexible leads and the appliance are in good condition.
- Check your plug sockets are not overloaded with too many electrical appliances as this can lead to overheating.
- Do not use appliance for other than intended use.
- Do not cut the cord, or put it on hot surfaces.
- Do not place on or near a hot gas or electric burner, or in a heated oven.
- Don’t try to clean or repair the appliance when it is still plugged in.
- Don’t wrap flexible cables around the appliance when it is still warm.
- Switch off the device when not in use.
- Please disconnect the power as soon as possible if the device falls into the water, the Warranty does not include water damage.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. Close supervision is necessary when any appliance is used by or near children.
Warranty
This Limited Warranty applies only to INKBIRD IHC-200-WIFI Humidity Controller.
What is Covered and for How Long
INKBIRD warrants that all new products are free from defects in manufacturing,
materials and workmanship for a period of one year from date of retail
purchase.
What this Warranty Does not Cover
The warranty does not cover defects or malfunction caused by misuse, abuse or
improper maintenance, failure to follow operating instructions, or use with
equipment with which it is not intended to be used. Also, the warranty will
not apply to damage caused by unauthorized alteration, modification or repair
of the product. INKBIRD does not warrant or provide service or support for any
third party products, including, but not limited to iPhones and Android
Phones.
How to Obtain Warranty Service
To obtain warranty service for products purchased from a third-party, retail
or directly from INKBIRD you must return the product with proof of purchase
using the following procedures:
-
Contact INKBIRD Customer Support for specific return and shipping instructions by email.
Email Address: support@inkbird.com You may be asked to complete a warranty service request form. And to help ensure warranty claims are for INKBIRD products, our technical support department may also require you to email a copy of your purchase receipt to us. -
Label and ship the product, freight prepaid, to the address provided by INKBIRD.
Exclusions and Limitations
THIS WARRANTY IS YOUR EXCLUSIVE WARRANTY AND REPLACES ALL OTHER WARRANTIES OR
CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED
WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. AS SOME STATES OR JURISDICTIONS DO NOT ALLOW THE EXCLUSION OF EXPRESS
OR IMPLIED WARRANTIES, THE ABOVE EXCLUSION MAY NOT APPLY TO YOU. IN THAT
EVENT, SUCH WARRANTIES APPLY ONLY TO THE EXTENT AND FOR SUCH DURATION AS
REQUIRED BY LAW AND ARE LIMITED IN DURATION TO THE WARRANTY PERIOD. AS SOME
STATES OR JURISDICTIONS DO NOT ALLOW LIMITATIONS ON THE DURATION OF AN IMPLIED
WARRANTY, THE ABOVE LIMITATION ON DURATION MAY NOT APPLY TO YOU.
FCC Requirement
changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interfer-ence received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equip-ment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunc-tion with any other antenna or transmitter.
INKBIRD TECH.C.L.
Support@inkbird.com
Factory address: 6th Floor, Building 713, Pengji Liantang Industrial
Area, NO.2 Pengxing Rd, Luohu Disctrict, Shenzhen, China
Office address: Room 1803, Guowei Building, NO.68 Guowei Rd, Xianhu
Community, Liantang, Luohu District,Shenzhen, China
Modifications: 1. Add version number 2. Update address
2022.04.02 Modifications:
1. Change of company information (remove the
QR code of the official website,
remove the URL, and add the office address)
2. Updated version number;
3. APP download QR code changed from inkbird
Pro to INKBIRD
App-related information changes;
4. The text inkbird is capitalized
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>