INKBIRD IBS-M2 Temperature Humidity Sensor User Manual

IBS-M2 Temperature Humidity Sensor

Overview

IBS-M2 Wi-Fi Gateway (receiver)

Specifications

• IBS-M2 Wi-Fi Gateway
• Transmission distance: up to 164 ft in open space, if there is interference, the transmission distance will be limited.
• Temperature Measurement Range: -10’C~60’C (14’F~ 140’F)
• Temperature Measurement Accuracy: ±1.0’C (±1.B’F)
• Temperature Display Accuracy: 0.1’C (0.1’F)
• Humidity Measurement Range: 0%RH ~99%RH
• Humidity Measurement Accuracy: ±5%
• Humidity Display Accuracy: 1%
• Maximum Number of Devices Supported: 9
• Wi-Fi: Supported

IBS-TH2 Temperature Humidity Sensor

• Powered by: 2 * AAA SV Batteries (not included)
• Temperature Measurement Range: -40’C~60’C (-40’F~ 140 ‘F)
• Temperature Measurement Accuracy: typical ±0.3’C/±0.5’F; max ±0.5’C/±0.9’F
• Humidity Measurement Range: 0%RH~99%RH
• Humidity Measurement Accuracy: typical ±3%RH; max ±4.5%RH
• RH Humidity Accuracy (25’C/77’F, 0%~ 100%): typical ±4.5%RH; max ±7.5%RH
• Waterproof Level: IPX4
• Warranty: 1 Year

App Connection

Download the INKBIRD App ****

Search the INKBIRD App from Google Play or App Store to get it for free, or you can scan the left QR code to download it directly.

Note: ****

1. Your iOS devices must be running iOS 0 or above to download the app smoothly.
2. Your android devices must be running android 4.4 or above to download the app smoothly.
3. The device supports a 4GHz Wi-Fi router only.

Registration

• Open the app, select your Country/Region, and a verification code will be sent to you.
• Enter the verification code to confirm your identity, and the registration is
• Registering an account is necessary before using the INKBIRD app for the first time.

Connect to your phone

• Open the app and click the”+” to select IBS-M2 to start the connection
• Plug into a USB power supply, power on properly, and click Next Step to continue
• Select the Wi-Fi to connect to, enter the password, and click Next Step to continue
• Press and hold the button on the device until the Wi-Fi indicator flashes to enter the pairing state, then click Next Step to continue.
• Your phone will automatically enter the device scan Once the device is found, click Next Step to continue.
• The device is automati­ cally pairing the network.
• Pairing is successful.

Note: If pairing fails, unplug the power supply and restart the device, then repeat steps 3.3.1~3.3.6 to try again.

Main Interface of INKBIRD App

Add Sub-Devices

1. First, plug in the IBS-M2 WiFi Gateway and power it on properly, then follow step 2 to start the app connection. Skip this step if the connection is already complete.
2. Second, install the batteries for the IBS-TH2 Temperature Humidity Sensor and power it on Be careful to place it as close as possible to the IBS-M2 WiFi Gateway.
3. Add sub-devices through the app, as shown in the following Choose the relevant device to be added, the sub-device will automatically establish a connection, add the device, and display the channel number of the IBS-TH2 Temperature Humidity Sensor.

Note : If adding a device fails, remove the battery of the IBS-TH2 Temperature Humidity Sensor and repeat steps b~c to try again.

Action Button Instructions

IBS-M2 Wi-Fi Gateway

CH/R Button:

• Press it to switch between the channels (CH1, CH2, ..CH9), the screen will display the measured tempera­ ture of the chosen channel (CH1, CH2, CH3…CH9). If CHO is selected, the measured temperature of each channel will be displayed alternately for 3 seconds.
• Press and hold it for 5 seconds to reset the registration of all IBS-TH2 Temperature Humidity Sensors. We should remove the batteries of the IBS-TH2 Temperature Humidity Sensor, reinstall them, then place the sensor close to the gateway to re-establish the connection and complete the registration.

“C/°F Button :
Press it to switch the temperature unit between “C and ‘F.

Button:
Press and hold it for 5 seconds to reset Wi-Fi and pair it with the network again.

Safeguards

1. Please do not disassemble the product if you are not a
2. Be sure that the sensor is not covered with dust as dust may lead to inaccurate measurements.
3. Do not use alcohol to clean the

Product Warranty

This item carries a 1-year warranty against defects in either components or workmanship. During this period, products that prove to be defective will, at the discretion of INKBIRD, be either repaired or replaced without charge.

FCC Requirement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• this device may not cause harmful interference, and
• this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving
• Increase the separation between the equipment and
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

INKBIRD TECH.C.L.

support@inkbird.com

Factory address: 6th Floor. Building 713, Pengji Liantang Industrial Area, N0.2 Pengxing Road, Luohu District, Shenzhen, China

Office address: Room 1803, Guowei Building, N0.68 Guowei Road, Xianhu Community, Liantang, Luohu District, Shenzhen, China

MADE IN CHINA

DESIGNED BY INKBIRD

Documents / Resources

| INKBIRD IBS-M2 Temperature Humidity Sensor [pdf] User Manual
IBS-M2, IBS-TH2, IBS-M2 Temperature Humidity Sensor, IBS-M2, Temperature Humidity Sensor, Humidity Sensor, Sensor
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>