ferplast Q01010 Koralia Wi-Fi Pump User Guide

ferplast Q01010 Koralia Wi-Fi Pump User Guide

SAFETY WARNINGS

DANGER

• To avoid possible electric shock, special care should be taken in the use of aquarium equipment. For each of the following situations, do not attempt repairs yourself; for assistance or to dispose of the device, return it to an authorised service centre.
• The appliance is not to be used by children or people with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction.
• Never run the pump out of water, do NOT run dry, the heat buildup may cause damage to its components.
• Always unplug with dry hands for any maintenance or service.
• KORALIA Wi-Fi pumps are 12VDC. Please ensure you use only the KORALIA Wi-Fi power supply.
• Ensure KORALIA Wi-Fi 12VDC power supply is plugged into an outlet with a drip loop (fig. 3).
• Avoid the possibility of the appliance plug, power supply or wireless hub from getting wet. Mount in aquarium stand where there is no possibility of water dripping onto them. For any wires for aquarium devices connected to electrical mains, the user must ensure that a “drip-loop” is created. A “drip-loop” is that part of the cord below the level of the receptacle, or the connector if an extension cord is used, to prevent water traveling along the cord and coming in contact with the appliance.
• Turn controller OFF and disconnect the pump from power before performing any service.
• Ensure KORALIA Wi-Fi pumps and any accessories all have a drip loop installed before plugging into the outlet.
• Only use in freshwater or saltwater applications, do not use pumps in other liquids.
• The KORALIA Wi-Fi pump utilizes very powerful magnets and can cause severe personal injury.
• This product carries a water ingress protection rating of IPX2 and the only portion that can be fully immersed in water is the pump. If the controller falls into the water, DON’T reach for it! First unplug it and then retrieve it. If electrical components of the controller get wet, unplug the controller immediately (Non- immersible equipment only).
• Carefully examine the appliance after installation. It should not be plugged in if there is water on parts not intended to be wet.
• Do not operate any appliance if it has a damaged cord or plug, or if it is malfunctioning or if it is dropped or damaged in any manner. Inspect power cord insulation to be sure there are no cuts or exposed wire. If so, Customer service would need to verify pump failure prior to warranty work.
• Always unplug an appliance from an outlet and battery backup when not in use, before putting on or taking off parts, and before cleaning.
• Never yank cord to pull plug from outlet. Grasp the plug and pull to disconnect.
• Do not use an appliance for other than intended use. The use of attachments is not recommended, and will invalidate any warranty.
• Make sure an appliance mounted on a tank is securely installed before operating it. Read and observe all the important notices on the appliance.
• To avoid injury, do not contact moving parts or hot parts such as heaters, reflectors, lamp bulbs, etc.

IMPORTANT
Before installation, read all safety instructions & warnings.

WHAT’S INCLUDED – fig.1

*According to your country standards

PUMP POSITIONING

1. Once you have chosen the location where you wish to install your KORALIA Wi-Fi pump, clean away any dirt, calcium deposits and algae (coralline or otherwise) using an aquarium scraper or scrubber.

2. Carefully separate the Dual Magnet Support System (DMSS) and place them on the clean glass.

3. Install cable protector wrapping around wave pump cable. This protects the pump cable from triggerfish, urchins and other animals that may damage pump cable (fig. 2).
   

4. Attach the KORALIA Wi-Fi pump and adjust it as desired.

5. If needed apply the adhesive cable clips on the external side of the aquarium glass. Make sure the glass is clean first

INSTALLING THE KORALIA Wi-Fi CONTROLLER – POWER SUPPLY

1. Choose a location underneath your aquarium cabinet free of excessive moisture and/or saltwater creep.
2. Using included wood mounting screw, mount the KORALIA Wi-Fi pump con-troller to stand.
3. Connect the pump cable to the KORALIA Wi-Fi controller pump output cable paying attention to align the two arrows on the connector before plugging in. Then turn the locking nut screw.
4. Repeat the operation with the power supply cord.
5. Now you can connect the main plug to the wall socket.
6. The KORALIA Wi-Fi controller’s led light on in white color for a while. Then the yellow colour will appear when the default Constant Flow mode at 50% starts.

Description – fig. 3

• A. Aquarium tank
• B. Appliance
• C. Power supply cord
• D. Drip Loop
• E. Attention

HYDOR APP – QUICK START GUIDE

App Store is a service trademark of Apple Inc.

Google Play and the Google Play logo are trademarks of Google Inc.

Download the HYDOR App and follow the steps on your device screen.
The device’s default password is: 12345678
To restore the device to factory settings and to update the firmware, hold down the controller’s button for 10 seconds.

CONTROLLER LED COLOURS CODE

• Yellow: Constant Flow

• Blinking orange: Wave mode

• Purple: Smooth

• Green: Random

• Cyan: Feed

• Blue: Night

• Blinking white – 1 second: press the KORALIA Wi-Fi controller button for 2 seconds to stop the pump for 10 minutes. Press again to start the pump manually.

• Blinking red – 0,5 second: locked rotor. The controller switches off the pump for 1 minute, then it tries again to power on the pump every minute if needed. In this way the controller prevents overheating issues. To avoid
  this kind of inconvenience remember periodically to clean the rotor and the rotor’s chamber.

• Blinking blue – 1 second: connection issues. The controller is not able to connect to the network. Check if your router is switched on and operating. Check if the SSID or/and PASSWORD of your home network are not changed.

• Blinking red/green – 1 second: Hardware error. Contact customer care.

MAINTANEANCE

Attention
Before any kind of intervention, always disconnect electrical supply of the pump and any other appliance placed in the water. Regular cleaning and maintenance will guarantee the pump better and longer performance. Clean the impeller assembly and the chamber removing deposits with a soft brush. Do not use detergents or solvents. If necessary clean the grid of the lower and upper chamber by putting it under running tap water or using a soft brush to remove algae and/or other residue.

This device contains
WI-FI Module
FCC ID: 2AC7Z-ESPWROOM02

GUARANTEE

The device is guaranteed for a period of 24 months from the date of purchase, against defects in material and/or workmanship. Our guarantee does not apply to claims the cause of which is due to installation and operation faults, lack of maintenance, misuse of the device, effects of frost, furring and lime deposits or amateur repair attempts.
The consumable materials and parts subject to wear and tear, that must be periodically replaced for normal maintenance of the device, are not included in our guarantee. In case of product returning, attach it together with the purchase receipt recording the date of purchase.

EUROPEAN UNION DISPOSAL INFORMATION

This symbol means that according to local laws and regulations your product should be disposed of separately from household waste. When this product reaches its end of life, take it to a collection point designated by local authorities.
Some collection points accept products for free. The separate collection and recycling of your product at the time of disposal will help preserve natural resources and ensure that it is recycled in a manner that protects human health and the environment.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>