Classic 12000 Set Top Box Tv Box User Manual

September 30, 2024
Classic

Classic 12000 Set Top Box Tv Box

Package Contents

Connection

AV Connection

  • A. Connect the AV cable of the 3 color (red/ white/yellow) to the Classic’s AV output interface and the other end to the TV’s AV input interface. The connection can be made by colour.
  • B. Power on the Classic. Set the TV video mode to AV input.

HDTV Connection

  • A. Connect HDMI cable to the Classic’s output interface and the other end to the TV’s HDMI input interface.
  • B. Power on the Classic. Set the TV video mode to HDTV input.

Installation Steps

  1. Connect The Classic Set-top box TV Box to the power supply.
  2. Connect The Classic to your TV with an HDMI Cable or AV Cable.
  3. For a wired connection, plug in an Ethernet cable from the TV Box to your modem or router. For wireless, choose your Wi-Fi network and input your Wi-Fi password.
  4. LED Light: Blue ON Red OFF Green INTERNET CONNECTION

Troubleshooting

Warning: Under no circumstances should you try to repair the Classic unit by yourself, as this will invalidate the warranty. Do not open it as there is a risk of electrical shock. If any fault occurs, please first check with this troubleshooting checklist. If you are unable to remedy a problem by following this guide, contact your dealer for help.

BT-350 Remote

BT-350 Remote – Learning Function
The learning function on the BT-350 remote is used to control your TV. You will be able to control: Power ON/OFF, Volume, and Input Source. To do this you will need the factory remote control for your TV.

  1. On the BT-350, press and hold the TV POWER + TV SOURCE for 3 seconds. Once the blue light turns on, release the buttons.
  2. Press the learning key you would like to program (TV POWER/ SOURCE/ TV VOL+/ TV VOL-) and the blue light will start flashing. The flashing blue light indicates the BT-350 is in learning mode.
  3. Align your TV Remote and the BT-350 so that the front transmitters are pointing at each other. They should be within 1 inch or 3 cm of each other.
  4. Press the button that you want to learn on the original remote. After receiving a learning function successfully, the red light on the BT-350 will blink 4 times.

BT-350 Remote – Bluetooth Pairing

  1. On your BuzzTV device, navigate to Settings > Remotes & Accessories > toggle Bluetooth to ON. Then choose: Add Accessory.
  2. On the BT-350, press and hold the VOL – & the OK Button for 3 seconds. Once the red light starts flashing, release the buttons.
  3. Select “BuzzTV BT-350” on your BuzzTV Device.
  4. You are now Bluetooth-paired. You can confirm this by looking for “BuzzTV BT-350” under the Remotes and Accessories Menu.

Note: If you do not select the key within 15 seconds after entering the learning state, it will automatically exit the learning state.

Please note not all TVs are compatible with source pairing

CEC settings to support the BT-350, your TV & your BuzzTV Box
If you were successful in TV source pairing the BT-350 to your TV then you need to make sure the CEC settings on both the TV and your BuzzTV Box are enabled and in some cases in the correct HDMI port on the TV, refer to your TV manual if needed. (Initially set to ON)

Voice Control

  • To use Voice control press the microphone button & say a command Only supported on certain models*

Backlight
To turn on or off the backlight press and hold the blue button for 3 seconds, the red LED will blink twice

Warranty Information

For warranty information and registration, please visit: www.buzztv.com/register

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Classic User Manuals

Related Manuals