H3C Magic NX54 Gigabit Dual Band Wi-Fi 6 Wireless Router User Guide

H3C Magic NX54 Gigabit Dual Band Wi-Fi 6 Wireless Router

USER GUIDE

Packing list: NX54, power adapter, network cable, installation quick start, compliance and safety manual.

• Image may differ from your actual product.

1. Connect the network cable

1. Use only the power adapter supplied with this equipment.
2. For better signal coverage, place the router in an area free of obstruction.

2. Set up a WI-Fl network

1. Connect to e WI-Fl of the router after the router ls installed. Password ls not required.
(The available WI-Fl names are on the device label.)

2. Follow the configuration wizard to proceed with settings.
{Enter 192.188.124.1 in your browser if the wizard does not opens.)

3. Configure Internet connection settings.
(The procedure varies by Internet access method.)

4. Reconfigure the Wi-Fi name and management password.
(The management password can be identical with the Wi-Fi password.)

Reconnect the Wi-Fi to access the Internet.

Ports, buttons, and LEDs

Set up a mesh Wi-Fi network

To provide good signal coverage throughout a large house, purchase multiple H3C routers that support mesh Wi-Fi and use the following procedure to set up a mesh Wi-Fi network:

1. Configure a router to access the Internet and use itas the controller.
2. Connect the other routers as agents to the network 60 seconds after they power up by using either of the following methods

Obselve the LED status on the agents during the mesh W~ nelwolk setup process.

• Steady green: Good connection.
• Steady orange: Fair oonneclion.
• Flashing orange: Fal ed connection.

Method 1: Wired networking

Use a network cable to connect a WAN port on the agent to a LAN port on the controller.

Method 2: Wlreless networking

Press the Mesh button on the controller and agent simultaneously. A mesh Wi-Fi network will be set up by the routers automatically within 2 minutes.

If multiple agents exist, repeat the preceding procedure to connect the agents one by one to the network.

Tips

Networking method

• As a best practice, use wired networking for a multi-floor house.
  To use wireless networking, make sure no isolation such as floor heating exists between floors, and try to place the routers at the same place on the upper and lower floors.

• As a best practice, use wireless networking for a large flat house.

Router placement

Try to distribute routers evenly in areas with less obstruction.
To use wireless networking, make sure less than two walls exist between routers.

FAQs(Frequently Asked Questions)

Q: Soma old devices cannot Identify or connect to the router WI-Fl. How

to deal with it?

This router is equipped with new-generation Wi-Fi 6 technology to improve wireless network connectivity. However, some old devices might have compatibility issues with it.

To resolve the issue, use either of the following methods:

• Upgrade the software of old devices.
• Enable Wi-Fi 5 Standby Network on the router.

Q: Fallad to access the Internet after the router configuration Is

complete. How to deal with It?

To resolve the issue:

1. To be sure that the network cable is connected correctly and reliably.
2. Make sure the Internet access method configured on the router is applicable at the installation site.

See the table to select the suitable Internet acx:ess method.

Warranty Card

Warranty terms and conditions:

H3C provides high-quality, high.performance products. To protecl: your rights and benefits, H3C provides the following warranty services:

•  The warranty period is three years from the purchase day.
• If the product cannot be used due to a quality issue within 30 days fmm the purchase day, the product can be replaced without charge.
• The power adapter has a 30-day warranty period. The warranty does not cover issues caused by other reasons than quality, such as damage by sharp objecta, broken pin, cable damage, or broken cable.
• Products repaired/replaced by H3C enjoy a 90-daywarranty from the date of repair/replacement, or continue to enjoy the original remaining warranty, whichever is longer.
• The accessories, induding the packaging material and cables, are not covered by the free warranty/replacement service.
• The purchase invoice is required for a warranty service. If the invoice cannot be provided, the warranty period shall be calculated from the shipment date.
• To ensure data security and protecl: your privacy, backup and delete data in the storage medium, if any, before returning the product for repair or replacement.

The warranty don not cover:

• Products not from H3C orwilhout proofs indicating they are from H3C.
• The SN label, tamper-proof label, or MAC address label is tom, damaged, or fabricated.
• Antenna damages caused by other reasons than material or manufacturing issue.
• Man-made physical damagu and damages caused by accidents.
• Defec:la and damages due to the pmdud being used in an abnormal environment
• Damages caused by unauthorized repair and modification.
• Nonnal wear and tear, and defecl!I and damages caused by corrosion or external power aourcea.
• Damages caused by force majeure such as earthquake, flood, tsunami, fire, typhoon, or lighting sbike.

Contact Info:

E-mail: Support.Maglc@h3c.com

Specifications

• Product Name: H3C Magic NX54 Wireless Router
• Model: NX54
• Components: Router, power adapter, network cable, installation quick start, compliance and safety manual

Version: 5W101-20240417
The information in this document is subject to change without notice.
Copyright © 2023-2024 New H3C Intelligence Terminal Co., Ltd.

Frequently Asked Questions (FAQ)

Q: How do I reset the router to factory settings?

A: Locate the reset button on the router (usually at the back).
Press and hold the button for about 10 seconds until the lights on the router flash. This will reset the router to its factory default settings.

Q: What should I do if I forget my Wi-Fi password?

A: You can reset the Wi-Fi password by accessing the router’s settings page through a wired connection. Navigate to the wireless settings section and create a new password.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>