FANIMATION 52-DY8723T Ceiling Fan Instruction Manual
- September 28, 2024
- FANIMATION
Table of Contents
52-DY8723T Ceiling Fan
“`html
Specifications:
- Model No.: 52-DY8723T
- Product: Ceiling Fan
Product Usage Instructions:
Safety Precautions:
-
For your safety, all electrical connections and disconnections
should be performed by a qualified electrician. -
Before installing the fan, remove the fuse or turn off the
circuit breaker to cut off the power. -
Ensure all electrical connections comply with local laws and
regulations. -
When mounting the fan, ensure there is at least 30 inches (76
cm) of space between the fan and any obstruction. -
The anchor point for the fan must support a weight of at least
100 pounds (45 kg). -
The fan’s electrical connection must be grounded to avoid any
dangerous branching. -
Do not connect the fan’s power supply to dimmers,
potentiometers, or light switches. -
Avoid using the fan along with gas installations in the same
room.
Installation Instructions:
Follow these steps for installing the ceiling fan:
-
Ensure power is cut off by removing the fuse or turning off the
circuit breaker. -
Mount the fan ensuring at least 30 inches of space from any
obstruction. -
Check that the blades are at least 7ft above the ground after
mounting. -
Securely fasten the fan to prevent loosening or turning.
-
Ground the fan’s electrical connection.
Maintenance Tips:
Remember to periodically check and tighten all fastenings to
avoid noise caused by loose elements. Additionally, check all
fastenings twice a year to ensure they are tight. If necessary,
retighten them to maintain stability.
Frequently Asked Questions (FAQ):
Q: Can I install the ceiling fan myself?
A: It is recommended that all electrical connections and
installations be performed by a qualified electrician for safety
reasons.
Q: How high should I mount the fan above the ground?
A: The fan blades should be no less than 7ft (2.1 m) above the
ground after installation.
“`
Model No.: 52-DY8723T
Ceiling Fan
Installation Instructions
THANK YOU We appreciate the trust and confidence you have placed in us through
the purchase
of this ceiling fan.We strive to continually create quality products designed
to enhance your home.Thank you for choosing us!
Safety Precautions
The information contained in the following pages has been prepared to
ensureyour maximum enjoyment of your fan Please remove the fuse or turn off
the circuit breaker to cut off the power before installing the fan. Ensure all
electrical connections are in compliance with local laws, regulations and
national eletrical codes. If you are not familiar with electrical installation
and wiring, please hire a qualified electrician or consult the wiring manual.:
1. For your safety, all electrical connections and disconnections should be
performed by a qualified electrician.
2. Any action performed for the electrical connection of the device must be
carried out after ensuring that the general power supply is disconnected,by
removing the corresponding fuse or disarming the protective switch in order to
ensure total isolation of the power supply.
3. When deciding where to mount the fan, be sure that there is at least 30
inches(76 cm) of space between the fan and any wall or other obstruction that
the fan blades could collide with. The greater this distance, the more
effective the air flow produced.After the fan is mounted, be sure that the
blades are no less than 7ft(2.1 m) above the ground.
4 . The anchor point for the fan must be able to support a weight of at least
100 pounds(45 kg). If mounting on a ceiling junctionbox, be sure that the fan
is adequately supported to prevent loosening or turning.
5. The fan’s electrical connection must be “grounded” (the fan’s ground cable
connected to the installation’s grounding network) in order to avoid any
branching that may be dangerous to people.
6. Do not connect the fan’s power supply to any dimmers,potentiometers, or
light switches, as it will cause the fan tomalfunction and/or will damage the
motor. The fan must be directly connected to a properly protected installation
circuit(magnetothermal differential switch with the adequate size for the
fan’s consumption and technical specifications).Only use the fan’s control to
turn it on or stop it.
7. It is recommended to not use these types of fans along with gas
installations simultaneously in the same room.
8. The fan must be not be moving and must have come to a complete stop before
changing its direction of rotation.This will prevent damage to its motor and
to the control unit, when applicable.
9. Do not insert anything that could hit the fan’s blades into its pathway
while it is moving, as this could cause damage to people, can damage the
blades, and can offset the balance of the unit, causing vibrations and
wobbling.
10. After installing the fan, ensure that all fastenings aresecure and
tightened in order to avoid any noise caused by loose elements.
11. Due to the fan’s movement, certain fastenings may become loose. Check all
fastenings twice per year at a minimum in order to ensure that they are
sufficiently tight. If necessary, they must be retightened.
12. The motor housing can be cleaned with a soft brush or a lint-free cloth
to avoid scratching the surface. Clean the blades with a lint-free cloth.
Important: Turn off the main power supply before starting any maintenance. Do
not clean the fans with water or a damp cloth.
Note: The important warnings and instructions indicated in this manual are not
guaranteed to cover all possible conditions and situations that may occur. It
must be understood that common sense, precaution, and care are factors that
cannot be included in all products. These factors can and must only be
provided by the user who maintains and enjoys this fan.
Tools Needed
Package Contents
1.Bracket
2.Down rod
3.Canopy 4.Coupling cover 5.Blade holder
6.Body/motor 7.Light kit 8. Light cover 9.Blades
Remote control unit
LIGHT ON
LIGHT OFF
WW NW DW
Z Z
Z
Blade balancing kit
Installation kit
Instructions manual
x11
x16 x3
x2 x4
Note:The Illustrations in this manual are for explanation purposes only and
may differ from the actual unit. It is subjected to change without prior
notice for further improvements.
.1.
Assembly Instructions
Step 1(Basic assembly of the fan)
æ Decompose drown rod.
ç Remove four screws from the fan body.
×8 Used to fix the fan blades
×4 Used to fix the light kit
è Route all the wires from the motor the down é Assemble the canopy and coupling cover
rod through. Fix the down rod to the coupling hanging ball through the down rod.Then
with bolt,and then insert the clevis pin.Last insert the fixing pin, push the Hanging ball
tighten the two screws on coupling.
up, and fix it with screws.
Tighten the screws
Step 2 (Installed bracket.)
æ Turn off the fan power supply at the circuit breaker box and the wall
switch.
Failure to disconnect the power supply prior to installation may result in serious injury or death.
OFF
.2.
Assembly Instructions
ç Can be installed on <10º sloped roof.
Choose the following installation methods according to the actual situation of
the roof.
OR
Octagon box
è Snap the basically assembled fan into
the installed bracket.
Solid wood roof
é Put the receiver into the bracket.
Convex Concave
Step 3 (Wiring .)
æ Make the wire connection in
accordance to the wiring diagram provided.
AC IN L(Black) AC IN N(White)
To Light
House power
To Motor
.3.
Ground wire
Assembly Instructions
Step 4 (Install remaining parts)
æ Loosen two screws on bracket.
ç Rotate the canopy clockwise until screw heads
engage the key slots fully. Tighten the screws. Be careful not to damage or
cut the wiring.
è Align the hole between blade and holder, screw the holes tightly with screw and gasket.
é Align the blades with the mounting holes,
and then fix them with screws.
ê Connect terminal.Then fix the light kit to
the main body with screws.Last installation light cover.
.4.
LIGHOTN
LIGHOTFF
WW
NW
DW
Assembly Instructions
Step 5(Switch on and ceiling fan works) ON
ZZ Z
.5.
Remote Control Operation
Transmitter learning process
1.Insert the 2 pcs of batteries into transmitter. 2.Turn on the power supply to the fan. Within 10 sec, press and hold the “1” and “2” button for about 3 sec. Once the receiver has detected the frequency, receiver will “Beep Beep” twice.Programming process is completed and fan is ready to use.
Press and hold for about 3 sec
NOTE: The remote control device has already been code matching when it leaves the factory.If the fan is not responding to the transmitter,repeat transmitter learning process.
LIGHT ON
LIGHT OFF
WW NW DW
Z Z
Z
ABOUT THE MEMORY FUNCTION OF LIGHTSPlease wait for more than 3-5 seconds keep this color that you need at first, and then turn off wait for at least 10 seconds turn on again. This light color would be your need.
IMPORTANT: The fan can only operate normally after all blades are installed. If the fan is turned on without installing the blades, the receiver will detect that the fan speed is too fast and the fan will automatically stop.
Remote Control Holder Installation
æ
ç
AAA 1.5V
è
LIGHT
ON
LIGHT OFF
é
WW NW DW
Z Z
Z
ê
ë
Transmitter Function
Light ON Light OFF
Fan Speed (1/2/3/4/5/6)
Fan Off
Warm light Press and hold: color temperature”K-” Day light Cool light Press
and hold: color temperature”K+” Forward/Reverse Sleep Wind Light brightness
“+”
Light brightness “-” Fan Timer (1hr,3hr,6hr)
.6.
TroubleShooting
Fan does not work
Fan turns but airflow is inadequate
1.Check all fuses or circuit breakers if disconnecting the power supply to the
fan. 2.Turn off electrical power and check all wire connections to fan and in
switch housing.It must be
carried out by a electrician
1.The fan may be running in reverse, so air is going upward. 2.The room may
contain items that obstruct the air flow. 3.The fan may be too small for size
of the room.
Fan is noisy
1. Assure that the screws fastening blade arm to motor are tight and the lock
washers provided for that purpose have been used
2.Lower the upper canopy to ensure a separation from the ceiling of no less
than 3mm to reduce noisy
3.Check to see if any of the blades are cracked .If so,replace all of the
blades 4.If this is the first use ,leave the fan on for at least 8 hours.In
the event that mechanical noise
continues after this period,contact certified electrician
Balancing Wobbling problems during fan operation
If the fan body wobbles during its operation, this is not a sign of malfunctioning (even if it wobbles
1
a few centimeters). To reduce wobbling, you can turn off the fan,and:
1.Check that all blades are properly fastened by tightening their screws.
2.Check the distance between each blade and the ceiling. Measurements to the ceiling can be
carried out as shown in the following diagram. If variations exist and you have already correctly
tightened the screws, check that all blades have the same shape. If any of them have a shape
that is visibly different, this may be causing an imbalance during fan operation.
If you have completed the previous steps and the wobbling has not resolved,you should apply
2
dynamic balancing with the kit provided, as explained below:
1.Turn the fan on to the highest speed so that the greatest amount of wobbling is produced.
2.Turn off the fan. Select a blade and place a clip on it (see diagram) halfway between the
fastening and the far edge of the blade.
3.Turn on the fan and check whether the wobbling has improved or gotten worse.Turn it off once
again and if the wobbling has not improved, place the clip on another blade. Repeat this process and determine on which blade it improves the wobbling.
3
4.Leave the clip on the blade that produces the best results. Move the clip forward or backwards
on this blade until finding the position that offers the best results.
5.Afterwards, remove the clip and place one of the weights on the upper part of the center line of
the blade at the position where the clip was located.
.7.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>