rfsolutions QS-RIOT-RX-WIFI-3 RIoT Receiver User Guide
- September 28, 2024
- rfsolutions
Table of Contents
QS-RIOT-RX-WIFI-3 RIoT Receiver
“`html
RIoT Receiver – Product Information
Specifications:
- Model: QS-RIOT-RX-WIFI-3
- Control Method: Wi-Fi via RIoT Control
Product Usage Instructions:
Configuring RIoT Receiver to Wi-Fi:
-
Ensure the RIoT Receiver is powered on.
-
Access the RIoT Control application on your device.
-
Follow the on-screen instructions to connect the RIoT Receiver
to your Wi-Fi network. -
Wait for the WHITE Net LED on the receiver to provide status
information; this process may take up to 30 seconds.
Safety Information:
-
Follow all safety precautions mentioned in the manual.
-
If the battery emits an unusual smell, feels hot, changes
color, or appears abnormal, discontinue use immediately. -
Qualified personnel should handle transmitter and equipment
operation. -
Regularly inspect the receiver housing and cables for
damage.
FAQ (Frequently Asked Questions):
Q: What should I do if the battery of the RIoT Receiver shows
signs of damage?
A: If the battery exhibits any abnormalities, such as an unusual
smell or change in appearance, stop using the receiver and contact
customer support for assistance.
Q: How long does it take to configure the RIoT Receiver to
Wi-Fi?
A: The configuration process may take up to 30 seconds. Please
be patient and wait for the WHITE Net LED to provide status
information.
“`
RIoT Receiver
Wi-Fi Quick Start Guide
Control RIOT RX Receiver via WiFi using RIoT Control
Follow this procedure to: · Configure RIoT Receiver to login to your local Wi-
Fi. · Pair RIoT Receiver to your Smart Device. · Configure optional Events /
Functions and Features
QS-RIOT-RX-WIFI-3
Configuring RIoT Receiver to Wi-Fi
QS-RIOT-RX-WIFI-3 Page: 2
Configuring RIoT Receiver to Wi-Fi
QS-RIOT-RX-WIFI-3 Page: 3
Configuring RIoT Receiver to Wi-Fi
Safety Information
Carefully read the following safety information before proceeding with
installation, operation, or maintenance of RF Solutions product. Failure to
follow these warnings could result in death or serious injury · This radio
system must not be used in areas where there is a risk of explosion. · Only
qualified personnel should be permitted to access the transmitter and operate
the equipment. · Always follow operating information as well as all applicable
safety procedures and requirements. · You must satisfy the age requirements in
your country for operating the equipment. · Store in a safe place. · Keep a
clear view of the work area at all time before using, check it is safe to do
so
Before maintenance intervention on any remote controlled equipment · Do not
open the receiver enclosure unless you are qualified. · Disconnect all
electrical power from the equipment. · Check the enclosure and cable for
damage regularly, do not use if there is evidence of damage.
Battery Precautions
· Risk of explosion if battery is replaced with a battery of an incorrect
type. · Do not short-circuit, disassemble, deform or heat batteries. · Never
attempt to charge a visibly damaged or frozen battery. · Do not use or charge
the battery if it appears to be leaking, deformed or damaged in any way. ·
Immediately discontinue use of the battery if, while using, charging, or
storing the battery, the
battery emits an unusual smell, feels hot, changes color, changes shape, or
appears abnormal in any other way.
Electrical Safety
ISOLATE the mains electricity supply before removing the cover and observe any
relevant safety information. · Maintenance to the product that involves
removal of the cover should only be carried out by a
competent person or qualified electrician. · Ensure adequate protection on the
Load circuit · Refer to Product Datasheet for MAX operating Load. · Product
must be installed in accordance with the local country electrical regulations.
· A current limiting supply must be used in accordance with the datasheet
QS-RIOT-RX-WIFI-3 Page: 4
Configuring RIoT Receiver to Wi-Fi
Information sur la sécurité
Lisez attentivement les informations de sécurité suivantes avant de procéder à
l’installation, l’utilisation ou la maintenance du produit RF Solutions. Le
non-respect de ces avertissements peut entraîner la mort ou des blessures
graves · Ce système radio ne doit pas être utilisé dans des zones présentant
un risque d’explosion · Seul le personnel qualifié doit être autorisé à
accéder à l’émetteur et à utiliser l’équipement. · Suivez toujours les
instructions d’utilisation ainsi que toutes les procédures et exigences de
sécurité applicables. · Vous devez satisfaire aux exigences d’âge dans votre
pays pour utiliser l’équipement · Il est strictement interdit d’utiliser
l’équipement sous l’influence de drogues, d’alcool et/ou de médicaments. ·
Conserver dans un endroit sûr. · Gardez une vue dégagée sur la zone de travail
à tout moment
Avant intervention de maintenance sur tout équipement télécommandé · N’ouvrez
pas le boîtier du récepteur à moins d’être qualifié · Coupez toujours
l’alimentation électrique de l’équipement. · Vérifiez régulièrement que le
boîtier et le câble ne sont pas endommagés, ne les utilisez pas s’il y a des
preuves de
dommages
Précautions Concernant la Batterie
· Risque d’explosion si la batterie est remplacée par une batterie d’un type
incorrect. · Ne pas court-circuiter, démonter, déformer ou chauffer les
batteries. · N’essayez jamais de charger une batterie visiblement endommagée
ou gelée. · N’utilisez pas et ne chargez pas la batterie si elle semble fuir,
déformée ou endommagée de quelque
manière que ce soit. · Cessez immédiatement d’utiliser la batterie si, lors de
l’utilisation, du chargement ou du stockage de la
batterie, la batterie émet une odeur inhabituelle, est chaude, change de
couleur, change de forme ou semble anormale de toute autre manière. · Gardez
les piles hors de portée des jeunes enfants. Si un enfant avale une pile,
consultez immédiatement un médecin.
Avertissements de sécurité
· ISOLER l’alimentation électrique avant de retirer le couvercle et observer
toutes les précautions de sécurité pertinentes.
· L’entretien du produit qui implique le retrait du couvercle ne doit être
effectué que par une personne compétente ou un électricien qualifié.
· La valeur nominale du fusible F2 est de 4A (T) 250 H (céramique). Remplacez
le fusible par le même type et la même valeur nominale.
· La sortie relais est évaluée à 10A en crête et 5A en constante. · Le produit
doit être connecté à une alimentation à fusible ou à une prise de connexion
appropriée ré-
pondant aux exigences du pays d’installation.
QS-RIOT-RX-WIFI-3 Page: 5
Configuring RIoT Receiver to Wi-Fi
Veiligheidsinformatie
Lees de volgende veiligheidsinformatie zorgvuldig door voordat u doorgaat met de installatie, bediening of het onderhoud van het RF Solutions-product. Het niet opvolgen van deze waarschuwingen kan de dood of ernstig letsel tot gevolg hebben
·
Dit radiosysteem mag niet worden gebruikt in gebieden waar explosiegevaar bestaat.
·
Alleen gekwalificeerd personeel mag toegang krijgen tot de zender en de apparatuur bedienen.
·
Volg altijd de bedieningsinformatie en alle toepasselijke veiligheidsprocedures en -vereisten.
·
U moet voldoen aan de leeftijdsvereisten in uw land voor het gebruik van de apparatuur.
·
Bewaar op een veilige plaats.
·
Houd te allen tijde een duidelijk zicht op het werkgebied voordat u het gebruikt, controleer of het veilig is om dit
te doen
Vóór onderhoudsinterventie op op afstand bediende apparatuur
·
Open de behuizing van de ontvanger niet tenzij u hiervoor gekwalificeerd bent.
·
Koppel alle elektrische stroom van de apparatuur los.
·
Controleer de behuizing en kabel regelmatig op beschadigingen, niet gebruiken als er tekenen van schade zijn
Voorzorgsmaatregelen voor de batterij
· Explosiegevaar als de batterij wordt vervangen door een batterij van een
onjuist type. · Batterijen niet kortsluiten, demonteren, vervormen of
verhitten. · Probeer nooit een zichtbaar beschadigde of bevroren batterij op
te laden. · Gebruik of laad de batterij niet op als deze lekt, vervormd of op
enigerlei wijze beschadigd is. · Stop onmiddellijk met het gebruik van de
batterij als de batterij tijdens het gebruik, het opladen of
opslaan van de batterij een ongewone geur afgeeft, warm aanvoelt, van kleur
verandert, van vorm verandert of er op een andere manier abnormaal uitziet. ·
Houd batterijen buiten het bereik van kleine kinderen. Raadpleeg onmiddellijk
een arts als een kind een batterij inslikt.
Electrische veiligheid
ISOLEER de netvoeding voordat u het deksel verwijdert en neem alle relevante
veiligheidsinformatie in acht.
· Onderhoud aan het product waarbij de afdekking moet worden verwijderd, mag
alleen worden uitgevoerd door een competent persoon of een gekwalificeerde
elektricien.
· Zorg voor voldoende bescherming op het belastingscircuit · Raadpleeg het
productgegevensblad voor de MAX bedrijfsbelasting. · Het product moet worden
geïnstalleerd in overeenstemming met de plaatselijke elektriciteitsvoor-
schriften van het land. · Er moet een stroombegrenzende voeding worden
gebruikt in overeenstemming met de datasheet
QS-RIOT-RX-WIFI-3 Page: 6
Configuring RIoT Receiver to Wi-Fi
Sicherheitsinformation
Lesen Sie die folgenden Sicherheitsinformationen sorgfältig durch, bevor Sie
mit der Installation, dem Betrieb oder der Wartung des RF Solutions-Produkts
fortfahren. Die Nichtbeachtung dieser Warnungen kann zum Tod oder zu schweren
Verletzungen führen. · Dieses Funksystem darf nicht in explosionsgefährdeten
Bereichen eingesetzt werden. · Nur qualifiziertem Personal sollte der Zugang
zum Messumformer und die Bedienung des Geräts ges-
tattet werden. · Befolgen Sie immer die Betriebsinformationen sowie alle
geltenden Sicherheitsverfahren und –
anforderungen. · Für den Betrieb des Geräts müssen Sie die Altersanforderungen
Ihres Landes erfüllen. · An einem sicheren Ort aufbewahren. · Behalten Sie vor
der Verwendung jederzeit freie Sicht auf den Arbeitsbereich und prüfen Sie, ob
dies
sicher ist
Vor Wartungsarbeiten an ferngesteuerten Geräten Öffnen Sie das
Empfängergehäuse nur, wenn Sie dafür qualifiziert sind. Trennen Sie die
gesamte Stromversorgung vom Gerät. Gehäuse und Kabel regelmäßig auf
Beschädigungen prüfen, bei Anzeichen von Beschädigungen nicht verwenden.
Vorsichtsmaßnahmen für den Akku
· Explosionsgefahr, wenn die Batterie durch eine Batterie eines falschen Typs
ersetzt wird. · Batterien nicht kurzschließen, zerlegen, verformen oder
erhitzen. · Versuchen Sie niemals, eine sichtbar beschädigte oder eingefrorene
Batterie aufzuladen. · Verwenden oder laden Sie den Akku nicht, wenn er
undicht, deformiert oder in irgendeiner Weise bes-
chädigt ist. · Stellen Sie die Verwendung des Akkus sofort ein, wenn der Akku
während des Gebrauchs, Aufladens
oder Lagerns einen ungewöhnlichen Geruch verströmt, sich heiß anfühlt, seine
Farbe ändert, seine Form ändert oder auf andere Weise ungewöhnlich erscheint.
· Bewahren Sie Batterien außerhalb der Reichweite von kleinen Kindern auf.
Sollte ein Kind eine Batterie verschlucken, suchen Sie sofort einen Arzt auf.
Elektrische Sicherheit
TRENNEN Sie die Netzstromversorgung, bevor Sie die Abdeckung entfernen und
beachten Sie alle relevanten Sicherheitshinweise. · Die Wartung des Produkts,
bei der die Abdeckung entfernt wird, darf nur von einer sachkundigen Per-
son oder einem qualifizierten Elektriker durchgeführt werden. · Sorgen Sie für
einen ausreichenden Schutz des Lastkreises · Siehe Produktdatenblatt für MAX
Betriebslast. · Das Produkt muss in Übereinstimmung mit den örtlichen
Elektrovorschriften des Landes installiert
werden. · Es muss eine Strombegrenzungsversorgung gemäß Datenblatt verwendet
warden.
QS-RIOT-RX-WIFI-3 Page: 7
Configuring RIoT Receiver to Wi-Fi
Información de seguridad
Lea atentamente la siguiente información de seguridad antes de continuar con
la instalación, operación o mantenimiento del producto de RF Solutions. El
incumplimiento de estas advertencias podría provocar la muerte o lesiones
graves. · Este sistema de radio no debe utilizarse en áreas donde exista
riesgo de explosión. · Solo se debe permitir el acceso al transmisor y operar
el equipo a personal calificado. · Siga siempre la información de
funcionamiento, así como todos los procedimientos y requisitos de
seguridad aplicables. · Debe cumplir con los requisitos de edad en su país
para operar el equipo. · Almacenar en un lugar seguro. · Mantenga una vista
clara del área de trabajo en todo momento antes de usar, verifique que sea se-
guro hacerlo Antes de la intervención de mantenimiento en cualquier equipo
controlado a distancia · No abra la caja del receptor a menos que esté
calificado. · Desconecte toda la energía eléctrica del equipo. · Compruebe la
carcasa y el cable en busca de daños con regularidad, no los utilice si hay
evidencia de
daños
Batterivarningar
· Riesgo de explosión si se reemplaza la batería por una de tipo incorrecto. ·
No cortocircuite, desmonte, deforme ni caliente las baterías. · Nunca intente
cargar una batería visiblemente dañada o congelada. · No utilice ni cargue la
batería si parece tener una fuga, estar deformada o dañada de alguna manera. ·
Interrumpa inmediatamente el uso de la batería si, al usar, cargar o almacenar
la batería, la batería
emite un olor inusual, se siente caliente, cambia de color, cambia de forma o
tiene un aspecto anormal de alguna otra manera. · Mantenga las baterías fuera
del alcance de los niños pequeños. Si un niño se traga una batería, consulte a
un médico de inmediato.
Seguridad ELECTRICA
AISLE el suministro eléctrico de la red antes de quitar la tapa y observe
cualquier información de seguridad relevante. · El mantenimiento del producto
que implica la extracción de la cubierta solo debe ser realizado por
una persona competente o un electricista calificado. · Asegurar una protección
adecuada en el circuito de carga. · Consulte la hoja de datos del producto
para conocer la carga operativa MÁXIMA. · El producto debe instalarse de
acuerdo con las normativas eléctricas locales del país. · Se debe utilizar un
suministro de limitación de corriente de acuerdo con la hoja de datos
QS-RIOT-RX-WIFI-3 Page: 8
Configuring RIoT Receiver to Wi-Fi
Informazioni sulla sicurezza
Leggere attentamente le seguenti informazioni sulla sicurezza prima di procedere con l’installazione, il funzionamento o la manutenzione del prodotto RF Solutions. La mancata osservanza di queste avvertenze può provocare morte o lesioni gravi
·
Questo sistema radio non deve essere utilizzato in aree a rischio di esplosione.
·
L’accesso al trasmettitore e l’utilizzo dell’apparecchiatura deve essere consentito solo a personale qualificato.
·
Seguire sempre le informazioni operative, nonché tutte le procedure e i requisiti di sicurezza applicabili.
·
È necessario soddisfare i requisiti di età nel proprio paese per l’utilizzo dell’apparecchiatura.
·
Conservare in un luogo sicuro.
·
Mantenere sempre una visione chiara dell’area di lavoro prima dell’uso, controllare che sia sicuro farlo
Prima dell’intervento di manutenzione su qualsiasi apparecchiatura telecomandata
·
Non aprire l’involucro del ricevitore se non si è qualificati.
·
Scollegare tutta l’alimentazione elettrica dall’apparecchiatura.
·
Controllare regolarmente la custodia e il cavo per verificare che non siano danneggiati, non utilizzare se vi sono
segni di danneggiamento
Precauzioni per la batteria
· Rischio di esplosione se la batteria viene sostituita con una di tipo
errato.
· Non cortocircuitare, smontare, deformare o surriscaldare le batterie.
· Non tentare mai di caricare una batteria visibilmente danneggiata o
congelata.
· Non utilizzare o caricare la batteria se sembra perdere, deformata o
danneggiata in alcun modo.
· Interrompere immediatamente l’uso della batteria se, durante l’utilizzo, la
ricarica o la conservazione della batteria, la batteria emette un odore
insolito, è calda, cambia colore, cambia forma o appare anormale in qualsiasi
altro modo.
· Tenere le batterie fuori dalla portata dei bambini piccoli. Se un bambino
ingerisce una batteria, consultare immediatamente un medico.
Sicurezza elettrica
ISOLARE l’alimentazione di rete ni di sicurezza pertinenti.
prima di rimuovere il coperchio e osservare tutte le informazio-
· La manutenzione del prodotto che comporta la rimozione del coperchio deve
essere eseguita solo da una persona competente o da un elettricista
qualificato.
· Garantire un’adeguata protezione sul circuito di carico
· Fare riferimento alla scheda tecnica del prodotto per il carico operativo
MAX.
· Il prodotto deve essere installato in conformità con le normative elettriche locali del paese.
· È necessario utilizzare un’alimentazione con limitazione di corrente in conformità con la scheda tecnica
QS-RIOT-RX-WIFI-3 Page: 9
Configuring RIoT Receiver to Wi-Fi
Receiver Status
Throughout the setup process, the WHITE Net LED provides status information.
Please be patient when configuring Wi-Fi, it can take up to 30 seconds to
update.
N et LED (WHITE)
RIOT Receiver
Status ON
Net LED (White)
Operating Mode
Description
Normal
RIoT Receiver is connected to Wi-Fi
1x Flash
RF Receive
RIoT Receiver has received a valid sig-
nal from a paired Sensor/Transmitter
2x Flash 3x Flash 4x Flash
Setup Mode Learn Mode Wi-Fi Error
In Setup Mode
RIoT Receiver is ready to Learn an
Sensor/Switch or Transmitter No Wi-Fi Connection
5x Flash Webservice Error
Cannot connect via Internet
QS-RIOT-RX-WIFI-3 Page: 10
Configuring RIoT Receiver to Wi-Fi Setup Procedure: Before you Start
You need a Smartphone / Tablet or Smart device connected to your local Wi-Fi
Download the following Apps from the Google Play or App Store:
+ OR
You now need to complete the following Tasks:
Stage 1 2 3 4
Description
Configure RIoT Receiver to your local Wi-Fi
Using RIoT Control App on a Smart device, or Using RIoT Control PRO App on a
Smart device
Event Timers
5
Configuring Data Encryption
Additional Features / Information
Profiles: Controlling Multiple RIoT Receivers
6
Auto Restore Outputs After Power Loss
App Setup
Application Circuit Drawing
Wi-Fi Factory Reset
QS-RIOT-RX-WIFI-3 Page: 11
Configuring RIoT Receiver to Wi-Fi
Configure RIoT Receiver to your to local Wi-Fi Stage 1
ANDROID version
1. Apply Power to the RIoT Receiver. 2. Press and hold the LEARN button until
the red LEARN LED stays ON (takes
~5 seconds), 3. Release the LEARN Button. 4. The NET LED will Flash 2X. RIoT
Receiver is now broadcasting its Wi-Fi SSID. 5. On your Android Smart device,
run the Wi-Fi Wizard App.
(Please note Location Services must be enabled) 6. Click on the Chain Links 7.
Follow the instructions to go to your Wi-Fi Settings 8. Connect to the
receiver Wi-Fi (starts ET, RH, EP, RH, etc)
Password is 0123456789
Note your Smart device may say “Internet may not be available” Connect to this
Wi-Fi
9. After connecting to your Wi-Fi, return to the Wizard App. 10.Select your
chosen Wi-Fi Network. 11.Input your password and press `Save’. 12.The Username
and password is saved to the RIoT Receiver 13.Close the Wi-Fi Wizard app.
14.The RIoT Receiver will reboot and connect directly to your local Wi-Fi.
This is indicated by the White NET LED being ON constantly.
QS-RIOT-RX-WIFI-3 Page: 12
Configuring RIoT Receiver to Wi-Fi
Stage 1
Configure RIot Receiver to your local Wi-Fi IOS Version
1. Apply Power to the RIoT Receiver. 2. Press and hold the LEARN Button until
the Red LEARN LED
stays ON. (takes ~5 seconds), 3. Release the LEARN Button. 4. The NET LED will
Flash 2X. RIoT Receiver is now broadcasting
its Wi-Fi SSID. 5. On your IOS smart device, run the Wi-Fi Wizard App.
(Please note Location Services must be enabled) 6. Press >
, which will take
you to your Wi-Fi settings.
6. Connect to RIoT Receiver Wi-Fi, (starts ET, RH, EL,etc) Password is
0123456789 7. Click the back button to return to the Wi-Fi Wizard app.
8. Wait for the RIoT Receiver to connect to your app. 9. Enter your Wi-Fi
network details, password. and press `Save’
10.RIoT Receiver will reboot, and connect directly to your local Wi-Fi.
This is indicated by the White NET LED being ON constantly.
QS-RIOT-RX-WIFI-3 Page: 13
Configuring RIoT Receiver to Wi-Fi Stage 2 Using RIoT Control App on your
Smart device
RIoT CONTROL App Introduction
This App provides a remote control handset as below;
Acknowledgement Feature:
The dot within each button Provides the Status of each receiver Output Circuit.
RED
Output Circuit OFF
YELLOW Updating
GREEN Output Circuit ON
To update the status press the ack refresh button,
Example showing all outputs ON
Example showing output1 ON, Outputs 2,3,,4 OFF
QS-RIOT-RX-WIFI-3 Page: 14
Configuring RIoT Receiver to Wi-Fi Stage 2 Using RIoT Control App on your
Smart device
RIoT CONTROL App Setup
1. Ensure your smart device and the Receiver are connected to the same Wi-Fi
network
2. Run RIoT CONTROL App
3. Select Menu, then `Add RIoT-RX’. 4. Your Smart Device is now ready to pair
with the
RIoT Receiver. 5. On the RIoT Receiver, briefly press the LEARN Button 6. APP
will show “Receiver Detected” message. 6. Select Yes. 7. Your Smart Device is
now paired with the RIoT Receiver.
9. Select Menu / Handset Type, to select your preferred handset
QS-RIOT-RX-WIFI-3 Page: 15
Configuring RIoT Receiver to Wi-Fi Stage 3 Using RIoT Control PRO App on your
Smart device
RIoT CONTROL PRO App Introduction Control PRO App provides more complex/custom
remote control. Individual Buttons can be created, labelled, monitored etc.
Individual RIoT Receiver outputs can be controlled. Combinations of RIoT
Receiver output circuits can be set to create “Mood Lighting”
QS-RIOT-RX-WIFI-3 Page: 16
Configuring RIoT Receiver to Wi-Fi Stage 3 Using RIoT Control PRO App on your
Smart device
RIoT CONTROL PRO App Installation 1. Run RIoT CONTROL PRO App 2. Select Menu,
then `Add RIoT-RX. 3. Your Smart Device is now ready to pair with the
RIoT Receiver. 4. On the RIoT Receiver, briefly, press the LEARN Button 5. APP
will show “Receiver Detected” message. 6. Select Yes. 7. Your Smart Device is
now paired with the receiver.
Add or Edit Buttons
Select menu Add /edit buttons
QS-RIOT-RX-WIFI-3 Page: 17
Configuring RIoT Receiver to Wi-Fi
Stage 3 Using RIoT Control PRO App on your Smartdevice
The Receiver Type: is RIoT Receiver Button Name: Here you can enter your own
text / Name Button Style: Select your preferred Style Circuit: Defines
Receiver output circuit relay control RF Module: should be set to 1 Control
Type: sets the output Circuit operation as below
Control Type Description
On/Off: Receiver output circuit will switch on/off
All On/Off:All Receiver output circuits will switch on/off
Timed: Mood:
Receiver output circuit will switch on for a preset time
Sets all the Receiver output circuits that are set to “Mood” to operate to a
preset combination.
In the example below, when the button is operated on the smart device, output circuits 1 and 3 will relax, and circuits 2 and 4 will operate.
QS-RIOT-RX-WIFI-3 Page: 18
Configuring RIoT Receiver to Wi-Fi
Stage 4 Event Timers – Initial Setup
Learning GPS Location
Before any event timers can be set, the RIoT Receiver must learn its GPS
location and local Dusk/Dawn times through out the year. Firstly ensure your
smart device is on the same Wi-Fi as the RIoT Receiver. 1. Apply Power to the
Receiver. 2. Press and hold the LEARN button until the red LEARN LED stays ON
(~5 secs). 3. Release the LEARN Button. 4. The NET LED will Flash 2X. Receiver
is now broadcasting its Wi-Fi SSID. 5. On your Android Smart device, run the
Wi-Fi Wizard App.
6. Click “>” 7. Select your device 8. RIoT Wizard Loads the RIoT-
Receiver settings
9. Select “Location” 10.Select “Detect” 11.”Save” settings 12.Select Daylight
Saving
The Dusk/Dawn times are calculated and saved to the RIoT Receiver
- Finally “Save ” (This process does not need to be repeated)
QS-RIOT-RX-WIFI-3 Page: 19
Configuring RIoT Receiver to Wi-Fi
Stage 4 Event Timers – Initial Setup
Dusk / Dawn Offset (minutes)
This “offsets” a Dawn or Dusk Event Timer operation by a number of minutes.
You can enter a positive or negative offset number. The effect is shown below
+ve Offset
day
night
Time
-ve Offset
Dawn
Dusk
Examples, Adding an offset of +10 causes: “Dusk” events to trigger 10 mins
before actual time of Dusk “Dawn” events to trigger 10 mins after actual time
of Dawn
Adding an offset of -10 causes: “Dusk” events to trigger 10 mins after actual
time of Dusk “Dawn” events to trigger 10 mins before actual time of Dawn.
QS-RIOT-RX-WIFI-3 Page: 20
Configuring RIoT Receiver to Wi-Fi
Stage 4 Setting an Event Timer
RIoT Receiver can be programmed to automatically switch its outputs circuits based on an Event Timer. Upto 16 Timers can be set based on the following Events
Preset Time Events Time ON to Time OFF
On for a set Time
Dusk Events Dusk to Dawn Dusk to OFF Time
Dusk Timer
Dawn Events Dawn to Dusk Dawn to Off Time
Dawn Timer
Set an Event Timer
Firstly ensure your smart device is on the same Wi-Fi as the RIoT Receiver.
1. On your Smart device, run the Wi-Fi Wizard App.
2. Click “>” 3. Select your device 4. RIoT Wizard Loads the RIoT-
Receiver Event Timers
1. Select a Timer to set/update. 2. Follow the procedure on screen to set-
up Timer type and circuit. 3. When completed 4. Click “>” to Save to the RIoT
Receiver
QS-RIOT-RX-WIFI-3 Page: 21
Configuring RIoT Receiver to Wi-Fi
Stage 5
Configuring Data Encryption
Data sent between a smart device the RIoT-RX is encrypted. The Encryption key
is a 16 digit string consisting numbers and letters, and can be modified to
create a unique encryption to your system. The encryption Key can be set in
the RIoT Receiver using the Wizard App, and can be set in the Control app or
Control PRO app on your Smart Device
The encryption keys must match for the system to work!
Default encryption key is: 0123456789ABCDEF (for older systems (RIoT-RX Rev 1
& 2 ) it is “UsernamePassword”)
To Set the Encryption Key within the Smart Device App.
1. Select Menu, then `App Setup
2. Update the encryption key as required and “Save”
QS-RIOT-RX-WIFI-3 Page: 22
Configuring RIoT Receiver to Wi-Fi
Stage 5
Configuring Data Encryption
To Set the Encryption Key within the RIoT Receiver
Firstly ensure your smart device is on the same Wi-Fi as the RIoT Receiver. 1.
Apply Power to the Receiver. 2. Press and hold the LEARN button until the red
LEARN LED stays ON. (takes ~5
seconds), 3. Release the LEARN Button. 4. The NET LED will Flash 2X. Receiver
is now broadcasting its Wi-Fi SSID. 5. On your Android Smart device, run the
Wi-Fi Wizard App.
6. Click “>” 7. Select your device
8. RIoT Wizard Loads the RIoT-Receiver settings 9. Update the encryption key as required and “Save”
QS-RIOT-RX-WIFI-3 Page: 23
Configuring RIoT Receiver to Wi-Fi
Stage 6
Additional Information / Features
Profiles – Control Many RIoT Receivers from one App
RIoT Control / Control PRO Apps can operate with Multiple Receivers located in
different locations. Each Receiver is set as a “Profile”. For Example the user
may have; A RIoT Receiver at Home, a RIoT Receiver at Work, a RIoT Receiver in
a shed etc. Each RIoT Receiver can be set as a named “Profile”
Profile Home Profile Work Profile Shed Profiles can be created and edited
under the App Menu.
Auto Restore Outputs After Power Loss
In the event of power recovery the RIoT Receiver can be set to automatically
restore the output Circuits to the status prior to the power loss.
Press MODE Switch
Until LED ON
Repeat Press LEARN Switch To set Auto Restore function:
10% LED ON 10% LED OFF
Press MODE Switch
To Confirm
QS-RIOT-RX-WIFI-3 Page: 24
Configuring RIoT Receiver to Wi-Fi
Stage 6
Additional Information / Features
App Setup Descriptions
There are various user setting from the Menu/App Setup which are described
below
Keep App Awake
This keeps the app displayed on your screen at all times, with real time
updates of the output Circuits appearing as they change or updated (from other
remote controls).
Disable Lock Screen
The App screen auto locks after 1 min, requiring the user to “swipe to unlock”
This prevents the App from auto locking the screen locking
Double Click Buttons (PRO App only)
Requires the user to double click when pressing a button, to help prevent
accidental touch operation
Local Mode
This restricts operation of the RIoT Receiver to smart devices that are
connected to the same local Wi-Fi as the RIoT Receiver. i.e. only smart
devices logged into the same local Wi-Fi (intranet) will have control of the
RIoT Receiver
QS-RIOT-RX-WIFI-3 Page: 25
Configuring RIoT Receiver to Wi-Fi
Stage 6
Additional Information / Features
Application Drawing – Switching a Light
FUSE
L N E
RELAY 1
RELAY 3
RELAY 4
NO COM NC
NO COM NC
NO COM NC
NO COM NC
12-32Vac/dc 0Vdc
230V INPUT SUPPLY
Wi-Fi Factory Reset
1. Remove Power from Receiver 2. Press and hold ERASE button, then apply
power . 3. Continue holding ERASE Button until Erase LED illuminates (~10sec)
3. Release the ERASE Button. All Wi-Fi settings are erased. Event timers and
paired RF transmitters are not erased.
QS-RIOT-RX-WIFI-3 Page: 26
Configuring RIoT Receiver to Wi-Fi
QS-RIOT-RX-WIFI-3 Page: 27
Configuring RIoT Receiver to Wi-Fi
Simplified Declaration of Conformity (RED)
BG – RF Solutions Limited , 2014/53/. : www.rfsolutions.co.uk CS -Tímto RF
Solutions Limited prohlasuje, ze typ rádiového zaízení definované v tomto
dokumentu je v souladu se smrnicí 2014/53/EU. Úplné znní EU prohlásení o shod
je k dispozici na této internetové adrese: www.rfsolutions.co.uk DA – Hermed
erklærer RF Solutions Limited , at radioudstyrstypen defineret i dette
dokument er i overensstemmelse med direktiv 2014/53/EU. EU-
overensstemmelseserklæringens fulde tekst kan findes på følgende
internetadresse: www.rfsolutions.co.uk DE – Hiermit erklärt RF Solutions
Limited , dass der Funkanlagentyp in diesem Dokument definiert der Richtlinie
2014/53/EU entspricht. Der vollständige Text der EU-Konformitätserklärung ist
unter der folgenden Internetadresse verfügbar: www.rfsolutions.co.uk EL – / RF
Solutions Limited , 2014/53/. : www.rfsolutions.co.uk EN – Hereby, RF
Solutions Limited declares that the radio equipment type defined within this
document is in compliance with Directive 2014/53/EU. The full text of the EU
declaration of conformity is available at the following internet address:
www.rfsolutions.co.uk ES – Por la presente, RF Solutions Limited declara que
el tipo de equipo radioeléctrico definido dentro de este documento es conforme
con la Directiva 2014/53/UE. El texto completo de la declaración UE de
conformidad está disponible en la dirección Internet siguiente:
www.rfsolutions.co.uk ET -Käesolevaga deklareerib RF Solutions Limited , et
käesolev raadioseadme tüüp määratletud selles dokumendis vastab direktiivi
2014/53/EL nõuetele. ELi vastavusdeklaratsiooni täielik tekst on kättesaadav
järgmisel internetiaadressil: www.rfsolutions.co.uk FI -RF Solutions Limited
vakuuttaa, että radiolaitetyyppi määratletud selles dokumendis on direktiivin
2014/53/EU mukainen. EUvaatimustenmukaisuusvakuutuksen täysimittainen teksti
on saatavilla seuraavassa internetosoitteessa: www.rfsolutions.co.uk FR – Le
soussigné, RF Solutions Limited , déclare que l’équipement radioélectrique du
type défini dans ce document est conforme à la directive 2014/53/UE. Le texte
complet de la déclaration UE de conformité est disponible à l’adresse internet
suivante: www.rfsolutions.co.uk HR – RF Solutions Limited ovime izjavljuje da
je radijska oprema tipa definirani u ovom dokumentu u skladu s Direktivom
2014/53/ EU. Cjeloviti tekst EU izjave o sukladnosti dostupan je na sljedeoj
internetskoj adresi: www.rfsolutions.co.uk HU – RF Solutions Limited igazolja,
hogy a dokumentumban meghatározottak szerint típusú rádióberendezés megfelel a
2014/53/ EU irányelvnek. Az EU-megfelelségi nyilatkozat teljes szövege elérhet
a következ internetes címen: www.rfsolutions.co.uk IT – Il fabbricante, RF
Solutions Limited , dichiara che il tipo di apparecchiatura radio definito
all’interno di questo documento è conforme alla direttiva 2014/53/UE. Il testo
completo della dichiarazione di conformità UE è disponibile al seguente
indirizzo Internet: www.rfsolutions.co.uk LT – As, RF Solutions Limited ,
patvirtinu, kad radijo rengini tipas apibrzta siame dokumente atitinka
Direktyv 2014/53/ES. Visas ES atitikties deklaracijos tekstas prieinamas siuo
interneto adresu: www.rfsolutions.co.uk LV – Ar so RF Solutions Limited
deklar, ka radioiekrta kas defints saj dokument atbilst Direktvai 2014/53/ES.
Pilns ES atbilstbas deklarcijas teksts ir pieejams sd interneta vietn:
www.rfsolutions.co.uk MT – B’dan, RF Solutions Limited , niddikjara li dan it-
tip ta’ tagmir tar-radju definit f’dan id-dokument huwa konformi madDirettiva
2014/53/UE. It-test kollu tad-dikjarazzjoni ta’ konformità tal-UE huwa
disponibbli f’dan l-indirizz tal-Internet li ej: www.rfsolutions.co.uk NL –
Hierbij verklaar ik, RF Solutions Limited , dat het type radioapparatuur
gedefinieerd in dit document conform is met Richtlijn 2014/53/EU. De volledige
tekst van de EU-conformiteitsverklaring kan worden geraadpleegd op het
volgende internetadres: www.rfsolutions.co.uk PL – RF Solutions Limited
niniejszym owiadcza, e typ urzdzenia radiowego zdefiniowane w tym dokumencie
jest zgodny z dyrektyw 2014/53/UE. Pelny tekst deklaracji zgodnoci UE jest
dostpny pod nastpujcym adresem internetowym: www.rfsolutions.co.uk PT – O(a)
abaixo assinado(a) RF Solutions Limited declara que o presente tipo de
equipamento de rádio definido neste documento está em conformidade com a
Diretiva 2014/53/UE. O texto integral da declaração de conformidade está
disponível no seguinte endereço de Internet: www.rfsolutions.co.uk
RF Solutions Ltd. Recycling Notice Meets the following EC Directives: DO NOT Discard with normal waste, please recycle. ROHS Directive 2011/65/EU and amendment 2015/863/EU Specifies certain limits for hazardous substances. WEEE Directive 2012/19/EU Waste electrical & electronic equipment. This product must be disposed of through a licensed WEEE collection point. RF Solutions Ltd., fulfils its WEEE obligations by membership of an approved compliance scheme. Environment Agency producer registration number: WEE/JB0104WV.
Waste Batteries and Accumulators Directive 2006/66/EC Where batteries are fitted, before recycling the product, the batteries must be removed and disposed of at a licensed collection point.
Disclaimer: Whilst the information in this document is believed to be correct at the time of issue, RF Solutions Ltd does not accept any liability whatsoever for its accuracy, adequacy or completeness. No express or implied warranty or representation is given relating to the information contained in this document. RF Solutions Ltd reserves the right to make changes and improvements to the product(s) described herein without notice. Buyers and other users should determine for themselves the suitability of any such information or products for their own particular requirements or specification(s). RF Solutions Ltd shall not be liable for any loss or damage caused as a result of user’s own determination of how to deploy or use RF Solutions Ltd’s products. Use of RF Solutions Ltd products or components in life support and/or safety applications is not authorised except with express written approval. No licences are created, implicitly or otherwise, under any of RF Solutions Ltd’s intellectual property rights. Liability for loss or damage resulting or caused by reliance on the information contained herein or from the use of the product (including liability resulting from negligence or where RF Solutions Ltd was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict RF Solutions Ltd’s liability for death or personal injury resulting from its negligence.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>