marta MT-OH2433B Oil Heater User Manual

MT-OH2433B Oil Heater

CAUTION
When using any electrical appliance, basic safety precautions should always be followed, including the following:
To ensure familiarity with the controls, safety features, and operation of your heater, read all instructions before use.

• Ensure familiarity with the controls, safety features, and operation of your heater, and read all instructions before use.
•  The danger of electric shock exists even when the appliance is switched off. ALWAYS unplug the unit when not in use.
• Unplug the heater by grasping the plug and pulling it from the outlet. NEVER YANK ON CORD.
• Do not insert and pull out the plug by wet hands, as this may cause electrical shock.
• Heater should never be used under conditions where it may be immersed, or come in contact with water. Similarly do not plug in your heater if its surfaces are damp.
• Do not operate the heater with a damaged cord set, or if it has been dropped, or damaged in any manner. Return it to an Authorized Service center for inspection, repairing and testing.
• Do not use outdoors.
• Do not leave the cable on hot surfaces.
• Disconnect the cord from the outlet before cleaning.
• When storing your heater, keep it in a cool, dry place.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Close supervision is required when any appliance is used by or near children.
• The surface temperature of the flanges is higher, during use, thus closely supervise any children in the area of this appliance.
• If malfunctions happen during operation, please put it to nearby appointed service center with the maintenance card. Never disassemble it by yourself.
• To avoid a circuit overload, do not operate another high wattage appliance on the same circuit.
• The heater must always operate in vertical position.
• Do not scrap the surface with rod or sharp hard tools, as this may cause deformation and rust because of damage of paint coat.
• During use surface temperature of the flanges is perhaps higher, thus do not touch it except handle, knob and the keys.
• Never use the unit in places with not flat and unstable surfaces. Make sure there are no flammable or easy deformed objects within 1m.
• The heater is suitable for operation on an A.C. electricity supply having the same voltage as that shown on its rating label. The unit should be earthed.
• Do not cover the appliance.
  CAUTION! Do not cover the heater while it is on. This can cause dangerous temperature increase.

BEFORE THE FIRST USE

• Unpack the appliance and remove all packaging materials and labels. Store warning labels (if available) and the product serial number plate on the housing!
• Clean the device with a damp cloth, clean the accessories in soapy water rinse thoroughly, and dry.

ASSEMBLING

IT IS PROHIBITED TO USE THE DEVICE WITHOUT INSTALLING SUPPORTS/WHEELS!

• Before using the device, attach the wheels to the supports. Unscrew the nuts from the wheels, insert the wheels into the supports from the inside, and screw the nuts securely.

• Then attach the supports to the base of the heater, to do this:
  1. Unscrew the wing nuts from the included U-brackets;
  2. Carefully turn the radiator over and place it on a carpet or other soft surface to avoid damaging the protective coating, attach brackets to the U-shaped flange between the first and second sections, and also between the last and penultimate sections;
  3. To attach the supports to the radiator body, insert the threaded ends of the U-shaped plates into the holes in the supports;
  4. Attach 4 wing nuts to the U-brackets and tighten the wing nuts securely. Note: Do not over-tighten as this may damage the flange.

• Turn the radiator over to its working position. MAKE SURE THAT THE APPLIANCE IS PUT ON WHEELS AND IS IN A STABLE VERTICAL POSITION!

CLEANING AND MAINTENANCE

• Always unplug the heater from the wall socket and allow it to cool down before cleaning.
• Clean the outside of the heater by wiping it with a damp cloth and buffing it with a dry cloth.
• Do not use any detergents or abrasives and do not allow any water to enter the heater.
• When the heater is not used for long periods of time it should be protected from dust and stored in a clean dry place.

SPECIFICATION

• Power supply (230 V, 50 Hz)
• Producer : Cosmos Far View International Limited Room 701, 16 apt, Lane 165, Rainbow North Street, Ningbo, China
• WARRANTY DOES NOT COVER SUPPLIES (filters, ceramic and non-stick coating, rubber seals, etc.)
  The production date is available in the serial number located on the identification sticker on the gift box and/or on the sticker on the device. The serial number consists of 13 characters, the 4th and 5th characters indicate the month, and the 6th and 7th indicate the year of device production. The producer may change the complete set, appearance, country of manufacture, warranty, and technical characteristics of the model without notice. Please check when purchasing the device. Current information about service centers is available on the website www.multimarta.com.

FAQs

Q: What should I do if the heater is not heating properly?
A: If the heater is not heating properly, check if the power switch is on, the thermostat is set correctly, and there are no blockages in the fins. If issues persist, contact customer support.

Q: How can I move the heater?
A: Use the handle provided to move the heater to different locations easily.

References

• Multimarta - интернет-магазин бытовой техники MARTA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>