GPSENKE GP-AG500 Series 733Mbps Dual Band Industrial AP Client Owner’s Manual

: September 27, 2024
: GPSENKE

Table of Contents

GP-AG500 Series 733Mbps Dual Band Industrial AP Client
Specifications:
Product Usage Instructions:
1. Installation:
2. Wireless Roaming:
3. Operating Modes:
4. Security Setup:
5. Network Configuration:
6. Quality of Service (QoS):

GP-AG500 Series 733Mbps Dual Band Industrial AP Client

“`html

Specifications:

Supports IEEE 802.11a/b/g/n/ac standard
Dual-band operation with data rates up to 733Mbps
Industrial-grade chipset with surge, ESD, and vibration
resistance protection
Supports various wireless security protocols and authentication
methods
Supports multiple operating modes including Client Mode, Bridge
Mode, and Router Mode
Supports dual Gigabit-RJ45 Ethernet ports and RS232/485 Serial
Port
Operating temperature range: -40°C to 80°C
Supports DC9-48V power supply
IP40 protection level

Product Usage Instructions:

1. Installation:

Install the GP-AG500 Series device on any equipment that
requires wireless connectivity under Client Mode.

2. Wireless Roaming:

Enable GP Roaming for seamless and rapid wireless roaming with
minimal packet loss between different frequency bands.

3. Operating Modes:

The device supports AP Mode, Client Mode, Bridge Mode (Layer 2),
and Router Mode (Layer 3). Choose the appropriate mode based on
your network requirements.

4. Security Setup:

Configure encryption and authentication methods to ensure
network security. Support for WPA, WPA2, MAC address verification,
and other security features is provided.

5. Network Configuration:

Set up IP addressing, DHCP, ACLs, NAT, and other network
parameters as needed for your specific network environment.

6. Quality of Service (QoS):

Utilize QoS policies for bandwidth management, speed limitation,
and call admission control to prioritize network traffic
effectively.

Frequently Asked Questions (FAQ):

Q: What is the maximum data rate supported by the GP-AG500

Series?

A: The device supports data rates up to 733Mbps.

Q: What security features are available on the GP-AG500

Series?

A: The device supports various encryption/authentication methods
including WPA, WPA2, MAC address verification, and more for
enhanced network security.

Q: Can the GP-AG500 Series operate in extreme

temperatures?

A: Yes, the device is designed to operate in temperatures
ranging from -40°C to 80°C.

“`

Industrial AP/Client 733Mbps Dual-Band
INDUSTRIAL NETWORK SOLUTION SPECIALIST WWW.GPSENKE.COM

INDUSTRIAL NETWORK SOLUTION SPECIALIST
Introduction
GP-AG500 Series is a high-performance wireless client designed for industrial WLAN applications. It utilized IEEE 802.11a/b/g/n/ac standard, support 2.4GHz &5GHz Dual-band with data rates up to 733Mbps. It designed with industrialgrade chipset, support surge, ESD and vibration resistance protection.
GP-AG500 Series can be installed on any device that requires wireless connectivity under “Client Mode”. It supports millisecond-level GP Roaming,offers seamless and rapid wireless roaming with none-package loss.
Meanwhile, it ensures quick handoffs between 2.4GHz and 5GHz based on specific scenario needs. GP-AG500 is particularly designed robot control system, intellegent Warehousing, AGVs system, power plant inspections.
Main Feature
l Support 802.11 b / g / n / ac Standard l Support 802.11 Wave1 (2-Stream), speed up to 733Mbps l Support MAC Address Clone l Support Millisecond Switching & GP Roaming l Support IPv4/IPv6 l Support Dual Gigabit-RJ45 Ethernet l Support RS232/485 Serial Port l Support MU-MIMO l Support Open System, Shared Key, WPA, WPA-PSK, WPA2-Enterprise, WPA2-PSK l Support DC9-48V Power Supply l Support IP40 Protection-Level l Support -40 80 Working Temperature
WWW.GPSENKE.COM

INDUSTRIAL NETWORK SOLUTION SPECIALIST

WLAN
Working Mode
Roaming RF

Software Parameter

Frequency Band

2.4GHz

5GHz

Channel Bonding

40MHz(Not Recommed)

80MHz

MU-MIMO

Support

OFDMA

Support

TWT

Support

433Mbps(PHY)

NA

Support

300Mbps(PHY)

Support

NA

A-MPDU

Support

MLD

Support

MRC

Support

STBC

Support

LDPC

Support

MAX Virtual AP

Single Band– Support 16 Virtual AP

Max Access Users Max Access Spend
RTS/CTS

128 ( Influenced by Environment Fators )
2.4GHz: 300Mbps 5GHz: 433Mbps
Support

CTS-to-self

Support

Hidden SSID

Support

Terminal Aging/Heartbeat Detection

Support

AP Mode Client Mode

Brigde Mode(LAY2) Router Mode(LAY3)
Support Client Mode Support MAC Address Clone

Roaming Switch

Support 802.11k, 802.11v, 802.11r LAY2/LAY3 Roaming

Load Balancing

Load balancing is supported based on the number of users and user traffic

5G Priority

Support

Automatic Channel Selection

Support

Automatic Power Regulation

Support

Intelligent Speed Select

Support

Time Fair Scheduling

Support

WWW.GPSENKE.COM

INDUSTRIAL NETWORK SOLUTION SPECIALIST

Security

Encryption Authentication Method

Support 64/128 bit WEPDynamic WEP TKIPCCMP encryption
Cooperate With AC Support WPAWPA-PSKWPA2- Enterprise WPA2-PSKWPA3MAC address VerifyWeb Verify
PPPoE Verification and etc Methods

LAY2 Isolation of Wireless Users

Support

wIDS

Support

AAA

RadiusClient
Authentication Server Multidomain configuration
Authentication Server Backup

Support Support Support

IP Address

Static IP and DHCP dynamically obtain addresses

IPv6

Support

LAY2/LAY3

ACL

Support

DHCP server

Support (Router Mode)

NAT

Support (Router Mode)

WMM(802.11e)

Support

Service Quality

Priority Mapping QoS Policy Mapping Bandwidth Managed Call Admission ControlCAC

Support
Support Support Bandwidth Speed Limitation
based on SSID and Users Support

Maintenance

Network Management

SNMPV1/V2c/V3TrapTelnetFTP/TFTPWEB

Size

Ethernet

Port

Antenna

Serial

Working Band

2.4G 5G

Hardware Parameter
81mm × 35mm× 100mm 2× 10/100/1000Base-T RJ45 Port
2 × RPSMA-K Antenna Port (External Antenna–Optional) 1×RS232/485
802.11 n/g/b: 2.4GHz-2.483GHz ( CHINA ) 802.11 ac/n/a:
5.150GHz-5.250GHz 5.725GHz-5.850GHz ( CHINA )

WWW.GPSENKE.COM

INDUSTRIAL NETWORK SOLUTION SPECIALIST

Modulation Technology
Modulation Method
MAX Transmit Power Adjustable Granularity Operating Temperature Storage Temperature
Operating Humidity IP Protection Level
Power Supply Consumption(Client5.8G)
MTBF
CE

OFDM : BPSK@6/9MbpsQPSK@12/18Mbps16-QAM@24Mbps 64-QAM@48/54Mbps DSSS : DBPSK@1Mbps DQPSK@2MbpsCCK@5.5/11Mbps
MIMO-OFDM 11n: MCS 0-15 MIMO-OFDM 11ac: MCS 0-9
11bDSS:CCK@5.5/11Mbps,DQPSK@2Mbps,DBPSK@1Mbps 11a/g OFDM:64QAM@48/54Mbps,16QAM@24Mbps,
QPSK@12/18Mbps,BPSK@6/9Mbps 11nMIMO-OFDM:BPSK,QPSK,16QAM,64QAM 11ac/ac wave2MIMO-OFDM:BPSK,QPSK,16QAM,64QAM,256QAM
16.16dBm
1dBm
-40ºC 75ºC
-40ºC 85ºC
0%~95%( Non-condensing)
IP40
DC9V-48V Power Supply
12W

250000H
IEC 61000-4-2 ESD: Contact: 8 kV; Air: 15 kV IEC 61000-4-3 RS: 80 MHz to 1 GHz: 3 V/m IEC 61000-4-4 EFT: Power: 2 kV; Signal: 2 kV IEC 61000-4-5 Surge: Power: 2 kV; Signal: 1 kV
IEC 61000-4-6 CS: 3 V IEC 61000-4-8 PFMF
Size Design

WWW.GPSENKE.COM

INDUSTRIAL NETWORK SOLUTION SPECIALIST

Appearance & Accessories

ANT1

DC9V~DC48V

SYS
SYS 5.8G 2.4G COM LAN1 LAN2

RS232/48 5
ANT2

DIN Installation
WAN/LAN1 LAN2

Packing*1

Device*1

Rubber Duck Antenna*2

Manual*1

Model Selection

Model

GP-AG500-3D-232 GP-AG500-5D-232 GP-AG500-3D-485 GP-AG500-5D-485

Speed GP-Q8203-RPS-J 3dbi
GP-Q8205-S-J 5dbi RS232 RS485

733M

WWW.GPSENKE.COM

INDUSTRIAL NETWORK SOLUTION SPECIALIST
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
·Reorient or relocate the receiving antenna. ·Increase the separation between the equipment and receiver. ·Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ·Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Information This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
WWW.GPSENKE.COM

INDUSTRIAL NETWORK SOLUTION SPECIALIST

This document and any part thereof may not be reproduced or used in any manner without the express written permission of GPSENKE (China). Product specifications are subject to change without prior notice. Please visit our website for the latest product information.