edelkrone LENS Controller User Manual

LENS
CONTROLLER
USER’S MANUAL
Before operating your edelkrone, please watch the user’s manual video.

http://edel.kr/fpp

WHAT’S IN THE BOX & THE BASICS

1. Lens Controller (with 015 mm rod clamp)
2. Rod for Lens Controller (224 mm, 184 mm, 134 mm)
3. Lens Gear (3 pcs.)
4. Rod Clamp (019 mm)
5. Calibration stand 6. Calibration chart

 ATTACHING LENS GEAR

If you have a cine lens, you don’t need to attach Lens Gear and may skip this step. If you don’t have 0.8 pitch on your lens, attach Lens Gear to your lens.
A detailed video explaining how to attach Lens Gear can be found at http://edel.kr/tpp

 REPLACING THE ROD CLAMPS & CHANGING CLAMP DIRECTION

You can use the Extra Rod Clamp (019 mm) according to your rod preference. To use it;

1. Loosen the screw and slide out the rod clamp (015 mm).
2. Separate the screw, rod holder and aligner.
3. Switch the 019 mm rod holder with 015 mm rod clamp and assemble it back.
4. Slide the rod clamp back to its place on Lens Controller and tighten the screw.
   i. You can change the direction of the rod damp to provide the proper position for your lens.
   (t)A detailed video explaining how to attach your Lens Controller can be r found at httylledetielfup

ATTACHING LENS CONTROLLER ONTO L-BRACKET

1. Attach your Lens Controller to L-Bracket.
2. You can use one of 3 different rod sizes according to your lens preference.
3. Make sure your Lens Controller gear connects with your lens or Lens Gear firmly.
4. Tighten the screw.
   ESA detailed video explaining how to attach your Lens Controller can be E found at: http://edel.kr/tpp

POWER OPTIONS

1. Attach your LP-E6 Battery onto Battery Bracket by sliding it.
2. You can also use DC IN socket to power up your Lens Controller. DC IN socket is the priority when DC IN and LP-E6 Battery are attached.
   ! DC IN socket does not charge the LP-E6 Battery.
    A detailed video explaining how to power up your Lens Controller can be r found at http://edeel.kr.tpp

 HOW TO USE CALIBRATION CHART

1. Place a tape measure on the calibration stand.
2. Place the calibration chat on the calibration stand.
3. If needed, use tape to secure tape measure on the calibration stand.
   A detailed video explaining how to use calibration chart & stand can be found at: http://edeel.kr.tpp

HOW TO USE CALIBRATION CHART (CONT’D)

1.  Set up your SliderPLUS on the ground as shown above. Make sure you have enough distance to open your measuring tape as long as possible.
2. Make sure the tilt axis of your HeadPLUS is perpendicular to the ground then mark it on the ground.
3. Then just follow the instructions on the edelkrone App.
   A detailed video explaining how to use calibration chart & stand can be j found at http://edeel.kr.tpp

START USING.

1. Downbad the edelkrone App to your mobile device from the App Store or Google Play. Links can be found at www.edelkrone.com/productsAens-controller
2. To operate Lens Controller, hold On/Off button down until the opening bar in the information screen is full-filled.
3. Lens Controller is now ready for smart pairing or manual pairing through Bluetooth/VVrfi.
4. After pairing the devices, you are now ready to use your Lens Controller. Just keep following the instructions on your mobile device or visit manuals.edelkrone.com for a detailed video instruction.

Always start using with a fully charged batteries.
Make sure your mobile device’s Bluetooth connection is on.
A detailed video explaining the edelkrone app usage details can be found at http://edeel.kr.tpp

DISPOSAL OF THE PRODUCT & WARNINGS

Should the product become damaged beyond repair, or if you wish to dispose of it, it must be disposed separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities. Observe the regulations of your area and country that relate to the disposal of electronic products.

• Keep your electronic Motion Control Unit away from all sods of liquids.
• In order to preserve your Motion Control Unit and battery performance at their best, use the exact same type of batteries with an equivalent level of charge during dual-battery operation.
• Do not attempt to disassemble or modify any internal parts of your Motion Control Unit. If the device appears to be malfunctioning, discontinue use immediately and contact support for qualified service.
• Never force a different type of connector into a port.
• Never use or store your Motion Control Unit in areas subject to extreme temperatures, or high levels of vibration.
• If your motion control unit becomes unresponsive, disconnect and re-connect the power source. Make sure your DC adapter is plugged in or your batteries are properly charged. If the problem persists, contact our support team. ‘ Environmental factors may affect your Motion Control Unit’s performance. Keep your product away from environmental hazards such as dust or heavy resonance. Do not use chemical materials to clean your product.
• Only use included battery plate, DC adapter or equivalent power sources. Use of an inappropriate power source may permanently damage your Motion Control Unit.
• If there is an impairment on the power or connector cable, stop using the Motion Control Unit immediately.
• Avoid dropping or causing physical damage to your Motion Control Unit. ‘ Do not place heavy objects on top of your Motion Control Unit.
• edelkrone carnet be held responsible for damage caused by Improper use or modification of the product.
• Rated Voltage: 7.4V-14.8V (7.4V LP-E6 Battery / AC-DC Adapter) Rated Current: 2A Operating Temperature: -5°C to +45°C
  For more Information and tips about your Lens Controller, please watch the user’s user manual video at http://edeel.kr.tpp

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>