edelkrone Handle Pack for PocketRig V3 User Manual

June 5, 2024
Edelkrone

edelkrone Handle Pack for PocketRig V3 User Manual

Whats in the box

  1. PocketRlG v3
  2. Shoulder support
  3. 15 mm rods
  4. Mounting wheels
  5. 1/4″-20 & 3/8″-16 mounting ports
  6. Arm length adjustment knob
  7. 3 mm Allen key
  8. M4x20 SHCS (2 pcs.)
  9. M4x16 SHCS (2 pcs.)
  10. 3/8″-16 female mounting piece (1 pcs.)
  11. 1 /4″-20 female mounting piece (4 pcs.)
  12. 3/8″-16 male mounting screw
  13. 1 /4″-20 male mounting screw
  14. Top cage part
  15. Side cage part
    Whats in the box

MOUNTING YOUR POCKETRIG v3 TO YOUR CAMERA

  1. Loosen the camera plate mounting wheel.
  2. Slide the camera plate as shown.
  3. Remove the camera plate.MOUNTING YOUR POCKETING v3 TO YOUR CAMERA
  4. You can use the mounting disc to screw 1 /4″-20 mounting screw located under the camera plate to screw the 1/4″-20 mounting screw.
    MOUNTING YOUR POCKETING v3 TO YOUR CAMERA

A detailed video explaining the mounting process can be found at:
http://edel.kr/prv3

MOUNTING YOUR POCKETRIG v3 TO YOUR CAMERA (COMT.)

  1. Screw the 1 /4″-20 mounting screw to your camera using the mounting disc.
  2. Snap the camera plate into the body.
  3. Slide the camera plate in the direction of the arrow as shown until you hear a click.
  4. Tighten the mounting wheel.
    MOUNTING YOUR POCKETRIG v3 TO YOUR CAMERA \(COMT.\)

LENS
Pay attention to the camera direction. Mount the camera according to the mark on the bottom of the camera plate.
A detailed video explaining the mounting process can be found at:
http://edel.kr/prv3

HOE TO USE POCKETRIG v3 ARM

  1. Swing open the shoulder support arm as shown.

HOE TO USE POCKETRIG v3 ARM

  1. Loosen the tension adjustment wheel.
  2. Extend the shoulder support arm and tighten the tension adjustment wheel.
  3. Rotate the shoulder support until it stops moving. HOE TO USE POCKETRIG v3 ARM

A detailed video explaining how to use the pocketrig v3 arm can be found:
http://edel.kr/prv3

HOW TO USE THE POCKETRIG v3 ARM (CONT.)

  1. To extend the arm downwards, swing the arm all the way out and rotate it down.
  2. Attach to your belt using the gap in the shoulder piece.
    HOW TO USE THE POCKETRIG v3 ARM \(CONT.\)

Using your belt allows you to shoot longer with heavier equipment without fatigue.

If you are not going to attach any equipment / accessories on the rods, keep them closed while using your PocketRlG.

While using the support arm, place the curved part on your chest. Hold your camera with your right hand and hold the lens with your left hand for the best stabilization.

To avoid getting pinched while folding and unfolding the system, always hold your camera with one hand and move the parts from the ends with your other hand.

A detailed video explaining how to use the rods can be found at:
http://edel.kr/prv3

ADJUSTING THE TENSION OF THE POCKETRIG v3 ARM

ADJUSTING THE TENSION OF THE POCKETRIG v3 ARM

PocketRiG v3 has three points for tension adjustments. You can adjust the tension of these points by using your 3 mm Allen key.

A detailed video explaining how to use the pocketrig v3 arm can be found at:
http://edel.kr/prv3

HOW TO USE THE FOLDABLE RODS

  1. Swing open the rods until they click and stop.
  2. Loosen the rod knob.
  3. Extend the rod as much as you want and tighten the rod knob back.
    HOW TO USE THE FOLDABLE RODS

A detailed video explaining how to use the foldable rods can be found at:
http://edel.kr/prv3

HOW TO SET FOCUS ON v2

If there is a gap between lens gear and focus wheel gear after you tighten the thumb screw and rod knobs, follow these steps:

  1. Loosen only FocusONE v2’s thumb screw.
  2. Push it back to the lens gear.
  3. Tighten the thumb screw as you push FocusONE v2 toward your lens.
    HOW TO SET FOCUS ON v2

A detailed video explaining how to use the foldable rods can be found at:
http://edel.kr/prv3

ATTACHING THE HALF CAGE ON POCKETRIG v3

  1. Remove the 3 mm Allen key from the magnetic surface of the should support.
  2. Screw x2 M4x16 SHCS.
  3. Screw x2 M4x20 SHCS.
    ATTACHING THE HALF CAGE ON POCKETRIG v3

A detailed video explaining how to attach the half cage can be found at:
http://edel.kr/prv3

HOW TO USE THE HALF CAGE

  1. Accessories with cold shoes can be attached anywhere on the half cage.
  2. After you set your cold shoe, use the security knobs to secure your accessories.
  3. 1 /4″-20 female mounting pieces can be used anywhere on the half cage.
  4. You can use the security knobs on the end of the cage to protect against any possible accidents.

FULL RIG SETUP

A detailed video explaining how to use pocketrig v3 can be found at:
http://edel.kr/prv3

DISCLAIMER

edelkrone cannot be held responsible for damage caused by improper use or modification of the product.

For more information and tips about your pocketrig v3, please watch the user manual videos at the link, http://edel.kr/prv3

QR code

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals