sewoo LK-P300 Mobile Printer Instruction Manual

sewoo LK-P300 Mobile Printer

Specifications

• Model: LK-P300
• Type: Mobile Printer (Wi-Fi & Bluetooth)
• Manufacturer: Aroot Co., Ltd.
• Address: 28-6, Gajangsaneopdong-ro, Osan-si, Gyeonggi-do,Republic of Korea, 18103
• Contact: TEL +82-31-8077-5000 / FAX +82-31-624-5310
• Website: www.miniprinter.com

Product Usage Instructions

Safety Precautions

For better safety and reliability, adhere to the following precautionary measures:

• Indication: Read and follow the instructions carefully before operating the product.
• Prohibition: Do not disassemble. Grounding to prevent electric shock.
• Must follow: Unplug the power from the outlet.Do not handle the product with wet hands.

Warnings

• WARNING: Failure to follow these instructions could result in fire, electric shock, other injuries, or property damage.
• WARNING: Do not pull or touch the power plug with wet hands. Potential risk of electric shock or fire.
• WARNING: Do not bend the wire and do not allow the wire to be pinched or crushed by heavy objects. Potential risk of electric shock or fire.
• WARNING: Do not overload an electrical outlet. Potential risk of electric shock or fire.
• WARNING: If a power plug is broken or a plug is cut or worn, do not use it. Potential risk of electric shock or fire.

Frequently Asked Questions

Q: What should I do if the printer does not connect via Wi-Fi or Bluetooth?
A: If you are experiencing connectivity issues, try the following steps:

• Ensure that the Wi-Fi or Bluetooth feature is enabled on both the printer and your device.
• Check if the printer is within the range of the Wi-Fi network or Bluetooth connection.
• Restart both the printer and your device.
• If the issue persists, refer to the troubleshooting section in the user manual or contact customer support.

Q: How can I replace the printer’s battery safely?
A: When replacing the battery, follow these steps to ensure safety:

• Use only the recommended battery type specified by the manufacturer.
• Dispose of the used battery according to local disposal instructions.
• Avoid exposing the battery to extreme temperatures or conditions that may lead to an explosion.
• If unsure, seek assistance from authorized service centers for battery replacement.

Aroot Co., Ltd.
28-6, Gajangsaneopdong-ro, Osan-si, Gyeonggi-do ,18103, Republic of Korea
TEL +82-31-8077-5000 / FAX +82-31-624-5310 / http://www.miniprinter.com

MODEL : LK-P300
MOBILE PRINTER(Wi-Fi & Bluetooth)

All specifications are subject to change without notice

Following information shall be included in the manual

Information to User;

Caution:
the user that changes or modifications not expressly approved by the Aroot Co., Ltd. responsible for compliance could void the user’s authority to operate the equipment.

NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Responsible Party;
The responsible party for Supplier’s Declaration of Conformity must be located within the United States, so you have to include following information in manual.

• Company name : Aroot Co., Ltd. (Manager : Vic Barczyk)
• Address : 19700 S. Vermont Ave. STE 200, Torrance, CA 90502 | USA
• TEL / FAX No : (TEL) +310-561-8030 / (FAX) +82-31-459-8880
• Homepage: http://www.miniprinter.com

Use of the Made for Apple badge means that an accessory has been designed to connect specifically to the Apple product(s) identified in the badge, and has been certified by the developer to meet Apple performance standards.
Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions.

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Risk of explosion if battery is replaced by an incorrectly type. Dispose of used battery according to the local disposal instructions.

• replacement of a battery with anincorrect type that can defeat a safeguard (for example, in the case of same lithium battery types)
• disposal ofa battery into fire or a hot oven, ormechanically crushing or cutting of a battery,that can result in an explosion;
• leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas ; and
• a battery subjected to extrmely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.

Disposal of Old Electrical &Electronic Equipment(Applicable in the European
Union and other European countries with separate collection systems)
This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronics equipment. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

Safety Precautions

For better safety and reliability, adhere to the following precautionary measures.
Read and follow the instructions carefully before operation of the product.

Indication

WARNING
Failure to follow these instructions could result in fire, electric shock,other injuries, or property damage.

CAUTION
Failure to follow these instructions could result in fire, electric shock,other injuries, or property damage.

Unpacking

Standard

Optional

Product overview

Control Panel Usage

Paper Installation

CAUTION
Make sure to be careful of the HOT head

1. Press the COVER OPEN button up to open the Paper cover. You can set the width of paper guide by turning the knob with your finger.
2. Place the paper roll as shown. Make sure the paper is placed in the right direction.
3. CAUTION
   Please make sure you hear the closing sound of the upper cover.

Pull a short length of paper out of the printer and close the cover.

4. CAUTION
   If the cover is not shut down completely, the printer may not work properly.

Please tear the paper down.

Power Save Function

Power Save Function
When the printer is idle for a period of time, the Power Save Function disables parts of printer’s functionality in order to minimize the power consumption and extend the hours of battery use.

The time for the various Power Save modes can be set from 0 to 60 minutes(Power off mode time 0 to 120minutes). Once the printer has been idle for that set amount of time, the printer will automatically enter the mode and disable specific functions, based on the below table.

a low power mode where only the LCD screen is turned off, but keeps both the Bluetooth & Wi-Fi interfaces enabled.

Deep Sleep mode time (maximum energy saving mode)

| Once the time elapses, the printer goes into the maximum energy saving mode, turning off both the LCD screen and the Bluetooth interface (If enabled). However, the WLAN interface, if enabled, will remain active and will receive data.

※ When in this mode and printing via Bluetooth, the printer will first need to be “woken” up by pressing any button on the control panel, before sending the print job to the printer.

Power off mode time| Once the time elapses, the printer turns itself off and can only be powered back on by pressing the Power ON button.

Setting up as a printer :

• For setting through the LCD screen, refer to the screen below.

NOTE

• Energy saving modes do not operate when the time is set to 0 minutes.
• When the power saving function is not activated, only the LCD Screen Saver operates.

Example 1: Enabling Only Sleep and Deep Sleep Modes

After being idle for 1 minute, the printer goes into Sleep (low power).
If the printer remains idle for 10 minutes, the printer goes into the Deep Sleep (maximum energy saving) mode.

Example 2: Enabling all 3 Power Saving Modes

After being idle for 1 minute, the printer goes into Sleep (low power) mode. If the printer remains idle for 10 minutes, the printer goes into Deep Sleep (maximum energy saving) mode. If this state continues for 1 hour, then the printer turns itself off.

Example 3: Disabling All 3 Power Saving Modes

To disable the three power saving modes, set the values to ‘0’ minutes. Only the LCD screen saver operates without any power saving function activated.

NOTE

• If more than one mode is set, the function is activated in the following order
  : Sleep mode → Deep Sleep mode → Power Off mode.

Recommended settings for Power Save Function

IF using only Bluetooth :

• It is convenient to set the deep sleep waiting time to ‘0’ to avoid entering deep sleep because automatic wakeup through data transmission to printer is not supported in deep sleep.
• Enable ‘BT’ from the LCD menu: Setting → Interface menu, or through the Configuration Tool’s Interface Settings menu. It is recommended to turn off the WLAN function in order to prevent power consumption due to WLAN radio.

IF using only WLAN :

• Since the WLAN radio is enabled even when in Sleep and Deep Sleep mode, it is recommended to enable the Deep Sleep mode in order to minimize energy consumption during standby time.
• It is also recommended to turn off the BlueTooth function in order to prevent power consumption due to BlueTooth radio.
• Enable WLAN and disable BlueTooth from LCD menu: Setting → Interface menu, or through the Configuration Tool’s Interface Settings menu.

IF using only USB :

• It is recommended to set the Deep Sleep mode in order to minimize energy consumption during standby time.
• It is also recommended to turn off the BlueTooth and the WLAN functions in order to prevent power consumption due to BlueTooth and WLAN radios.
• Select ‘None’ from LCD menu setting → interface menu, or or through the Configuration Tool’s Interface Settings menu.

Battery

Battery Installation

Please make sure you hear the click sound of the battery.

1. Align battery hook as shown in the picture.
2. Push the battery into the printer until it locks in place.

NOTE

• As the battery is not charged at the time of your purchase, charge the battery prior to using the printer.

Battery Removal

Remove the battery as shown.

1. Press up on the battery handle and lift it up.
2. Remove the battery.

Battery Charging

1. Make sure the printer is turned off.
2. After opening the cover, connect the to the printer.
3. Plug the power cord into the electrical outlet.

NOTE

1. If the charger provided by the manufacturer is not used, the printer can be damaged, and the manufacturer is not liable for the consequential damage.
2. Before removing the battery, make sure that power is turned off.
3. The printer does not work when only connected to the charger.
4. While charging, do not turn on the power.
5. Do not operate the printer while charging the battery.

Charging Cradle
Optional

1. Insert the battery into the battery charger as shown above.
2. Connect the DC JACK to the electrical outlet.
3. Plug the power cord into the electrical outlet.
4. Once the charging is completed, remove the battery from the charger.

The charging status LED

NOTE

• In the case the battery is not inserted properly, the red LED will blink.
  Remove and reinsert the battery.

Set Cradle

1. Place and slide the product from top to bottom of the Set Cradle as shown in the picture.
2. Connect the USB cable to the Set Cradle.
3. When charging is complete, push the Cradle Lever and take out the product to the top of the Set Cradle.

Battery Charging Status

Belt Strap

1. Prepare the belt strap.
2. Put the strap into the strap bracket hole as shown.
3. Turn the strap and printer over and put the strap into the hook as shown.
4. Adjust the strap length for the user’s convenience.

 Self Test

1. Turn off the power by pressing the power button for approximately 3 seconds.
2. While you are holding the FEED button, press the power button.
3. The self-test will print.

NOTE

1. To enter hex dump mode, press the FEED button once more.
2. If the FEED button is not pressed,the self-test will automatically finish after 3 seconds.

Self-Test Printout Sample

Upon initial installation or for troubleshooting, you can run the diagnostic test to get information about:

• Firmware version, emulation,codepage, sensor settings,interface settings, etc.

If no issues are found with the diagnostic test, examine other devices and software.

The diagnostic test is working independently of devices and software.

Motor protection from being overheated
To prevent the motor from overheating, stop the printer for at least 30 seconds after continuously printing 1.5 meters.

Peripheral Connection

This product can communicat with oher devices via Bluetooth or a communication cable.

Bluetooth Connection

1. The Printer can be connected to devices equipped with Bluetooth communication capabilities(PDAs, PCs, etc.).
2. Use the Bluetooth connection function supported by your device to connect to the printer.
3. You can easy pairing with Bluetooth using NFC tag.

NOTE

• This model supports numeric comparison function.
• Please refer to the configuration manual for details.

Wi-Fi Connection

1. The Printer can be connected to devices equipped with Wi-Fi communication capabilities (PDAs, PCs, etc.).
2. Use the Wi-Fi connection function supported by the device to connect to the printer.

NOTE

• Please refer to the CONFIGURATION MANUAL for details.

USB Connection

1. Flip over the connector cover and connect USB cable to the printer connector.
2. Connect the interface cable to the USB port of the device (PDA, PC, etc.).

NOTE

• Only use cables included with the printer. (USB)

Cleaning the Printer

If the interior of the printer is dusty, printing quality can be reduced. In this case, follow the instructions below to clean the printer.

NOTE

1. Make sure to turn the printer power off prior to cleaning.
2. Regarding printhead cleaning, as the printhead gets very hot during printing, turn off the printer power and wait approximately 10 minutes before cleaning.
3. When cleaning the printhead, take care not to touch the heated portion of the printhead. The printhead can be damaged by static electricity.
4. Take care not to allow the printhead to become scratched and/or damaged in any way.
5. When using a linerless paper, clean regularly at least once after using 4~5 rolls or a week (Cleaning cycle may vary depending on usage.)

Print-Head Cleaning

1. Use the cleaning pen to clean the head of the printer.
2. Once the cleaning is completed, wait a few minutes before inserting the paper roll into the printer.

Platen Roller Cleaning

1. Use a cleaning pen to clean the rollers.
2. Wipe the entire Roller by rotating it with your fingers. 3 When using a linerless paper,wipe the surrounding parts that touch the surface of the paper.

JAM Error

1. When you face with a paper jam error, please press the button up to open the PRINTER COVER.

2. CAUTION
   Make sure to be careful of the HOT head.
   Please remove the paper.

3. NOTE
   Please make sure you hear the closing sound of the upper cover.

NOTE
If the cover is not shut down completely, the printer may not work properly.

After removing, close the cover. The printer will work normally.

Black Mark

Gap

Printer Specification

Utilities

The following utilities and concerned manual can be found on the QR or homepage.

1

|

PrinterGear

| Tphriinstiesrawnitihntbeeglroawtedtausktisli.ty that you can manage your

– Printer Configuration Settings

– Wireless-Lan Settings

– Font(Bitmap/TrueType) Download

– Printing service

– Document management

– FW Download

※- Maintenance o PrinterGear Manual for detailed

infPolremasaetiorenf.er t

2| LabelMaker(CPCL)| Tlahbieslpprroignrtainmg.is for label form design and designed
3| (SAenwdoroiMd _UUtitliiltiyty) (ESC/POS)| Iettcis. athurotiuligtyhaBplpuetthoaottphrainntds tWexi- tF,ibcaormcomdeusn,iicmataiognes, , and able to printer settings.

S/W

We provides SDK, Driver, etc. as follows to respond to various S/W usage environments.

You can download this S/W from the homepage.

1

|

PrinterGear

| Tphriinstiesrawnitihntbeeglroawtedtausktisli.ty that you can manage your

– Printer Configuration Settings

– Wireless-Lan Settings

– Font(Bitmap/TrueType) Download

– Printing service

– Document management

– FW Download

※- Maintenance o PrinterGear Manual for detailed

infPolremasaetiorenf.er t

2| LabelMaker(CPCL)| Tlahbieslpprroignrtainmg.is for label form design and designed
3| (SAenwdoroiMd _UUtitliiltiyty) (ESC/POS)| Iettcis. athurotiuligtyhaBplpuetthoaottphrainntds tWexi- tF,ibcaormcomdeusn,iicmataiognes, , and able to printer settings.

References

• SEWOO

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>