sewoo SLK-T32EBII Receipt Printer Instruction Manual

: September 21, 2024
: sewoo

Table of Contents

woo SLK-T32EBII Receipt Printer
Parts Identifications
Setting Up the Printer
Control panel and other functions
Self Test
ASCII Print
ECO Mode
Printer Setting
Hexadecimal Dump
Printer Cleaning
Linerless Printer
Specifications
Command-List
Utilities
The following utilities and manuals can be found on the CD or homepage.
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

woo SLK-T32EBII Receipt Printer

Aroot Co., Ltd.
28-6, Gajangsaneopdong-ro, Osan-si, Gyeonggi- do, 18103, Republic of Korea TEL : +82-31-8077-5000 / FAX : +82-31-624-5310 http://www.miniprinter.com

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions.

This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.

Tim Kloeker
19700 S Vermont Ave Ste 200 Torrance, CA 90502 | USA NA_Sales@miniprinter.com

Victor Almazan
Paseo de la Reforma No. 265 Piso 2.Oficina SBC. Col. Cuauhtémoc, C.P. 06500 Ciudad de Mexico | Mexico LA_Sales@miniprinter.com

Disposal of Old Electrical &Electronic Equipment(Applicable in the European Union and other European countries with separate collection systems)
This symbol on the product or its packaging indicates that this product shall not be treated as household waste. Instead, it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. For more detailed information about recycling this product, please contact your local city office, your household waste disposal service, or the shop where you purchased the product.

Parts Identifications

Setting Up the Printer

Unpacking
Your printer box should include these items. If any items are damaged or missing, please contact your dealer for assistance.

Connecting the Cables
You can connect the cables required for printing to the printer. They all connect to the connector panel on the back of the printer, which is shown below :

Before connecting any of the cables, make sure that both the printer and the computer are turned off.

Interface Connector

9Pin Serial Interface

PIN

2

| SIGNAL

R

| I/O

Input

| Description

receive data line

---|---|---|---
3| TXD| Output| Printer tamit datline
45, 7| GDNTR| Output| Dyastta TermoinaldReady
| D| –| S em Gr un
86| DSR| Input| Data Set Ready
1, ,9| NC| –| –
| | |

USB Interface

PIN

1

| SIGNAL

+5V

| I/O| Description

+5iV

---|---|---|---
2| DATA-| –| Pr nter transmit data line
3| DANTA+| | Pyrisnter tGraonusmit data line
4| G D| –| S tem r nd
| | |

USB Interface

PIN

1

| SIGNAL

t t +

| I/O

---|---|---
2| Data Out –| Output Data –
3| Data CIN +| Input Data +
4| N.| –
5| N.C| –
6| Data IN –| Input Data –
7| N.C| –
| |
8| N.C| –

This equipment is indoor use and all the communication wirings are limited to inside of the building.

Cash Drawer Connector
The printer can operate two cash drawers with a 6 pin RJ-11 modular connector. The driver is capable of supplying a maximum current of 1.0A for 510ms or less when not printing.

PIN

1

| SIGNAL

Signal GND

| Description

–

---|---|---
2| Drawer kick-out drive signal 1| Output
3| Drawer open/close signal| Input
4| +24V| –
5| Drawer kick-out drive signal 2| Output
6| Signal GND| –
| |

Loading the Roll Paper

NOTE
Be sure to use paper rolls that meet the specifications. Do not use paper rolls that have the paper glued to the core because the printer cannot detect the paper end correctly. Turn off the power switch.

Make sure that the printer is not receiving data; Otherwise, data may be lost.
Open the paper roll cover by pushing down the cover open button.
Remove the used paper roll core if there is one inside.
Insert new paper roll as shown.
Be sure to note the correct direction that the paper comes off the roll.
Pull out a small amount of paper, as shown. Then, close the cover.
Tear off the paper as shown.

CAUTION
When the paper is jammed with the cutter, the top cover might be stuck. In this case, repeat power on and off several times. If the top cover is still stuck, please follow the steps to release the papers from jamming.

Make sure the printer is turned off.
Take out the cutter cover as shown.
Turn the screw with drivers to a direction until the paper is released from the cutter.

Adjustment of paper width

Please adjust the Paper Guide to fit the paper width in the direction of the arrow.
Tight the screw after adjusting the Paper Guide.
Pull the edge of the paper once the paper roll is installed correctly and close the Paper Cover.

Control panel and other functions

Control panel
You can control the basic paper-feeding operations of the printer with the button on the control panel. The indicator lights help you monitor the printer’s status.

Control Panel

Button
The button can be disabled by the ESC c 5 command. Press the FEED button once to advance the paper one line. You can also hold down the FEED button to feed the paper continuously.

Error indicators

STATUS

Power off

| PAPER| ERROR| POWER| REMARKS

Normal power is not supplied to the printer

---|---|---|---|---
RED

OFF

| RED

OFF

| GREEN

OFF

Power on| OFF| OFF| ON| Normal power is supplied to the printer
On line| OFF| OFF| ON| Normal error-free mode
Cover| | | |
open

Peanpder

| OFF| ON| ON| Close cover
ePaarpeenr| OFF| ON| ON| Insert the new paper roll
n d| ON| OFF| ON| Paper is low

Self Test

The self-test result indicated whether the printer was operating properly. Also with this, the user can check the following options or the status of the printer.

Control circuit
Printer mechanism
Printing quality
ROM version
Interface setting

This test is independent of any other equipment or software.

Running the self-test

Make sure the printer is turned off and the printer cover is closed properly before performing the self-test.
Turn the printer on by holding the FEED button, then the self-test will start.
The self-test prints the printer setting value and then prints the following, and pauses. (Error LED On)
SELECT MODE BY BUTTON
ASCII PRINT
ECO MODE
PRINTER SETTING
HEXADUMP MODE
Press the FEED button consecutively (1~4)
1. (ApSrCeIsIsPtRhIeNFTEED button once)

2. (ECO MODE

| Printing test page constructed with ACII code.

Set the ECO mode to save paper and power.

---|---
Press the FEED button twice)

3. (PReINsTER SETTINuG

| (Default font type, Reduce paper margin, Density) Set the printer option.
4. pr s the FEED b ton triple time)

HEXADUMP MODE

| (Serial baud rate, Cutting mode, Error beep, Melody)
(press the FEED button quad time)| Printing the HEX value received from the interface

* Wait for 5~6 seconds if you want to exit. Printer performs a cutting when exiting this mode

The printer is ready to receive data after finishing the settings.

ASCII Print

ASCII PRINT is printing a test page constructed ASCII code. You can able to check the printer works properly with this The ASCII PRINT test automatically ends and cuts the paper after printing the following: Completed The printer is ready to receive data as soon as it completes the ASCII PRINT.

ECO Mode

After entering the ECO MODE, the list that can select the ECO option will be printed. Similar to Self Test, you can press the FEED button to select an ECO option. Once the input performs properly, the printer shows a result and stores it.

ECO MODE

FONT SETTING
LINE SPACE SETTING
LINE FEED SETTING
BARCODE[1D] HEIGHT
DENSITY SETTING

Font
THE FONT SETTING menu can be changed to the Font mapping(FONT A / FONT B). If you do not want the other side font, you can disable that.

FONT A : 12×24
FONT B : 9×17

FONT SETTING

FONT A -> A / FONT B -> B
FONT A -> B / FONT B -> B
FONT A -> A / FONT B -> A
FONT A -> B / FONT B -> A

Paper Reduce

A reduced menu (Line space, Line feed, barcode[1D] height) was developed for paper saving.

Line space “Line space” means the amount of feed when you intentionally generate newlines.
Line feed “Line feed” means the amount of feed when there is an automatic line break.
Barcode Height “Barcode Height” means the height of the barcode when creating a one-dimensional barcode.

LINE SPACE SETTING

NORMAL
REDUCE 50%
REDUCE 75%
REDUCE 90%

LINE FEED SETTING

NORMAL
REDUCE 50%
REDUCE 75%
REDUCE 90%

1D BARCODE HEIGHT SETTING

NORMAL
REDUCE 50%
REDUCE 75%
REDUCE 90%

Density

Adjust the print density to save the power consumed by the printer.

SELECT DENSITY

NORMAL
LOW
DARK

Printer Setting

Change the printer settings. The options below can also be changed via the Memory Saver.

PRINTER SETTING

SELECT BAUDRATE
SELECT CUTTING MODE
SELECT THE ERROR BEEP OPTION
SELECT MELODY OPTION

Baudrate
After entering the BAUDRATE MODE, the list which can select the BPS will be printed. Similar like Self Test, you can press the FEED button to select a BAUDRATE. Once the input performs properly, the printer shows a result and stores it. The printer is ready to receive data as soon as it completes the SELECT BAUDRATEMODE.

SELECT BAUDRATE

4800bps
9600bps
19200bps
38400bps
57600bps
115200bps

Cutter
Set cutter mode.

SELECT CUTTING MODE

PARTIAL CUT
FULL CUT

Error Beep
If the cover is open or there is no paper, the error beep function is activated. This option allows you to enable / disable the error beep.

SELECT ERROR BEEP OPTION

BEEP ON
BEEP OFF

Melody
To DK Port (Cash), Melody box or external buzzer can be connected. You can activate it from the Melody Setting menu, and the melody will operate after the cutting operation.

Melody Box: Melody is fixed and the volume can be adjusted.
External Buzzer: 3 types of melody are output according to the Melody Type setting and volume control is not included.

SELECT MELODY OPTION

MELODY SETTING
SELECT MELODY TYPE

MELODY SETTING

MELODY ON AFTER CUTTING
MELODY OFF

SELECT MELODY TYPE

MELODY-Ⅰ
MELODY-Ⅱ
MELODY-Ⅲ

Hexadecimal Dump

This feature allows experienced users to see exactly what data is coming to the printer. This can be useful in finding software problems. When you go into the hex dump function, the printer prints all commands and other data in hexadecimal format along with a guide section to help you find specific commands.

To use the hex dump feature, follow these steps

Please turn printer off.
Please turn printer on while press down “Feed” button.
Press the FEED button three times when the Self Test printed.
Now printer had entered Hexa dump mode.
Run any software program that sends data to the printer. The printer prints ”Hexadecimal printing mode…” and then all the codes it receives in a two-column format. The first column contains the hexadecimal codes and the second column gives the ASCII characters that correspond to the codes.
Hexadecimal Dump
- 1B 21 00 1B 26 02 40 40 .!..& . @ @
- 1B 25 01 1B 63 34 00 1B .%..c4.
- 41 42 43 44 45 46 47 48 ABCDEFGH
- A period (.) is printed for each code that has no ASCII equivalent.
Turn off the printer.
Turn on the printer.

Printer Cleaning

If the interior of the printer is dusty, printing quality can be lowered. In this case, follow the instructions below to clean the printer.

NOTE

Make sure to turn the printer power off before cleaning
Regarding print head cleaning, as the print head is very hot during printing, turn off the printer power and wait approximately 10 minutes before starting.
When cleaning the print head, take care not to touch the heated part of the print head. The print head is subject to be damaged by static electricity.
Take care not to allow the print head to become scratched and /or damaged in any way.
Use an applicator swab moistened with an alcohol solution to clean the print head and remove any dusts.
Once the cleaning is completed, insert paper roll into the printer few minutes later and close the printer cover.

Preventing Overheating
To prevent the motor from overheating, continuous operation of the printer should be 1.5 m or less in print length. Set the pause time for 30 seconds or more than it.

Linerless Printer

Linerless Printer Cleaning
Paper dust or impurities inside the printer may cause printing problems. Please clean as below.

Open the printer cover and clean the paper PASS part.
Remove the paper if it is jammed.
Remove impurities from the cutter blade with a cleaning pen or alcohol.
Wipe the printer head and roller with a cleaning pen.
Wipe the paper detection sensor with a cotton swab or cloth.
When using linerless paper, please perform cleaning before using 30 Rolls or within a week.

NOTE
If the adhesive builds up due to poor cleaning, printing problems may occur.

Recommended Paper
MAX International Converters, Inc. MAXStick Products Ltd(USA)

WARNING
We are not responsible for any paper use issues other than recommended paper, which may result in poor print quality or damage to the product.

Specifications

Printing Method	Direct Thermal
Printing Speed	T32EB – Max. 200 mm/sec T32EBⅡ- Max. 220 mm/sec Linerless –

Driver

| Windows Driver(XP ~, Server2003 ~),Win- dows CE & Mobile Driver(CE 4.2 ~, Mobile

5.0 ~),Linux Driver, Mac Driver, OPOS Driver, JavaPOS Driver, iOS SDK, Android(6.0 ~) SDK, Windows SDK, Windows CE SDK Linux SDK

Paper

Cutter

| Type| Guillotine
---|---|---
Life| T32EB – 1,500,000 cuts T32EBⅡ- 2,000,000 cuts

Linerless – 1,000,000 cuts

Command-List

No.

1

| Command

HT

| Function

Horizontal tab

| REMARKS
---|---|---|---
2| LF| Print and line feed|
3| CR| Print and carriage return|
4| FF| Print and return to standard mode(in page mode)|
5| CAN| Cancel print data in page mode|
6| DLE EOT| Real-time status transmission|
7| DLE ENQ| Real-time request to printer|
8| DLE DC4| Generate pulse at real-time|
9| ESC FF| Print data in page mode|
10| ESC SP| Set right-side character spacing|
11| ESC !| Select print mode(s)|
12| ESC $| Set absolute print position|
13| ESC %| Select/cancel user-defined character set|
14| ESC &| Define user-defined characters|
15| ESC *| Set bit-image mode|
16| ESC –| Turn underline mode on/off|
17| ESC 2| Select default line spacing|
18| ESC 3| Set line spacing|
19| ESC =| Select peripheral device|
20| ESC ?| Cancel user-defined characters|
21| ESC @| Initialize printer|
22| ESC D| Set horizontal tab positions|
23| ESC E| Turn emphasized mode on/off|
24| ESC G| Turn double-strike mode on/off|
25| ESC J| Print and feed paper using minimum units|
26| ESC L| Select page mode|
27| ESC M| Select character font|
28| ESC R| Select an international character set|
29| ESC S| Select standard mode|
30| ESC T| Select print direction in page mode|
31| ESC V| Turn 90° clockwise rotation mode on/off|
32| ESC W| Set printing area in page mode|
33| ESC ＼| Set relative print position|
34| ESC a| Select justification|
35| ESC c 3| Select paper sensor(s) to output paper-end signals|
36| ESC c 4| Select paper sensor(s) to stop printing|
37| ESC c 5| Enable/disable panel buttons|
38| ESC d| Print and feed paper n lines|
39| ESC p| General pulse|
| | |
No.| Command

ESC t

| Function

Select character code table

| REMARKS
---|---|---|---
40| ESC {| Turn upside-down printing mode on/off|
41| FS p| Print NV bit image|
42| FS q| Define NV bit image|
43| GS !| Select character size|
44| GS $| Set absolute vertical print position in page mode|
45| GS *| Define downloaded bit image|
46| GS /| Print downloaded bit image|
47| GS B| Turn white/black reverse printing mode on/off|
48| GS H| Select printing position of HRI characters|
49| GS I| Transmit printer ID|
50| GS L| Set left margin|
51| GS P| Set horizontal and vertical motion units|
52| GS V| Select cut mode and cut paper|
53| GS W| Set printing area width|
54| GS ＼| Set relative vertical print position in page mode|
55| GS a| Enable/disable Automatic Status Back(ASB)|
56| GS f| Select font for HRI characters|
57| GS h| Set bar code height|
58| GS k| Print bar code|
59| GS r| Transmit status|
60| GS v 0| Print raster bit image|
61| GS w| Set bar code width|
62| | |
| | |
| < Add >| |
1| ESC i| Full cut|
2| ESC m| Partial cut|
3| FS !| Set print mode(s) for Kanji characters|
4| FS &| Select Kanji character mode|
5| FS –| Turn underline mode on/off for Kanji character|
6| FS .| Cancel Kanji character mode|
| FS…2 c1| |
7| d1 dk FS C| Define user-defined Kanji characters