sewoo LK-P34 Mobile Printer Wi-Fi and Bluetooth User Manual

sewoo LK-P34 Mobile Printer Wi-Fi and Bluetooth

Aroot Co., Ltd.
28-6, Gajangsaneopdong-ro, Osan-si, Gyeonggi-do ,18103, Republic of Korea TEL +82-31-8077-5000 / FAX +82-31-624-5310 / http://www.miniprinter.com

MODEL : LK-P34

MOBILE PRINTER(Wi-Fi & Bluetooth)

All specifications are subject to change without notice

The following information shall be included in the manual

FCC STATEMENT

Caution:
the user that changes or modifications not expressly approved by the J. STEPHEN Lab., Ltd.responsible for compliance could void the user’s authority to operate the equipment.

NOTE:
This equipment has been tested and found to comply with the limits for a Class B  digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and,  if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,  which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Responsible Party;
The responsible party for the Supplier’s Declaration of Conformity must be located within the United States, so you have to include the following information in the manual.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions.

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Tim Kloeker
19700 S Vermont Ave Ste 200 Torrance, CA 90502 | USA NA_Sales@miniprinter.com

Victor Almazan
Paseo de la Reforma No. 265 Piso 2.Oficina SBC. Col. Cuauhtémoc, C.P. 06500 Ciudad de Mexico | Mexico LA_Sales@miniprinter.com

CAUTION
Risk of explosion if the battery is replaced by an incorrect type. Dispose of used batteries according to the local disposal instructions.

• Disposal of Old Electrical&Electronic Equipment(Applicable in the European Union and other European countries with separate collection systems) This symbol on the product or its packaging indicates that this product shall not be treated as household waste. Instead, it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. For more detailed information about recycling this product, please contact your local city office, your household waste disposal service, or the shop where you purchased the product.

Safety Precautions

For better safety and reliability, adhere to the following precautionary measures. Read and follow the instructions carefully before the operation of the product.

Indication

WARNING Failure to follow these instructions could result in fire, electric shock, other injuries, or property damage.

WARNING
Failure to follow these instructions could result in fire, electric shock, other injuries, or property damage.

CAUTION
Failure to follow these instructions could result in fire, electric shock, other injuries, or property damage.

Unpacking

Standard

Optional

Product overview

Front

Rear

AMC(Advanced Manual Cutter) BUTTON

• AMC function gives the convenient way for users to cut papers.

Button Up

• Press the button up to cut the paper.

Button Down

• Press the button down to open the cover.
• Please press the button down and open the cover in situations such as cleaning the head, replacing a paper, and having a paper jam error.

CAUTION
Please stay your fingers away from the printer head after pressing up the AMC button with cover open. There is the risk of finger injury due to a projecting cutter blade.

Control panel usage

Paper Installation

CAUTION
Make sure to be careful of the HOT head

Press the AMC button down to open the paper cover.

Place the paper roll as shown. Make sure the paper is placed in the right direction.

CAUTION
Please make sure you hear the closing sound of the upper cover.

Pull a short length of paper out of the printer and close the cover.

CAUTION
If the cover is not shut down completely, the printer may not work properly

Press the AMC button up to cut the unnecessary paper.

Battery

Battery Installation

• Please make sure you hear the closing sound of the upper cover.
  1. Align battery hook as shown in the picture.
  2. Push the battery into the printer until it locks in place.

NOTE
As the battery is not charged at the time of your purchase, charge the battery prior to using the printer.

Battery Removal

• Remove the battery as shown.

Battery Charging

1. Make sure the printer is turned off.
2. After opening the DC JACK cover, connect the DC JACK to the printer. 3 Plug the power cord into the electrical outlet.
   Status| charging| charging complete
   ---|---|---
   Charging Lamp| Red| Green

NOTE

1. If the charger provided by the manufacturer is not used, the printer can be damaged, and the manufacturer is not liable for the consequential damage.
2. Before removing the battery, make sure that power is turned off.
3. The printer does not work when only connected to the charger.
4. The battery needs to be installed to operate the printer.
5. While charging, do not turn on the power.
6. Do not operate the printer while charging the battery.
7. Do not connect the charger while the printer is operating.

Charging Cradle Optional

1. Insert the battery into the battery charger as shown above.
2. Connect the DC JACK to the electrical outlet.
3. Plug the power cord into the electrical outlet.
4. Once the charging is completed, remove the battery from the charger.

The charging status LED

NOTE
In the case the battery is not inserted properly, the red LED will blink. Remove and reinsert the battery.

Belt Strap

1. Prepare the belt strap.
2. Put the strap into the strap bracket hole as shown.
3. Turn the strap and printer over and put the strap into the hook as shown.
4. Adjust the strap length for the user’s convenience.

Self Test

1. Turn off the power by pressing the power button for approximately 3 seconds.
2. While you are holding the FEED button, press the power button.
3. The self-test will print.

NOTE

1. To enter hex dump mode, press the FEED button once more.
2. If the FEED button is not pressed,
3. The self-test will print.

NOTE

1. To enter hex dump mode, press the FEED button once more.
2. If the FEED button is not pressed, the self-test will automatically finish after 3 seconds.

Self-Test Printout Sample

Upon initial installation or for troubleshooting, you can run the diagnostic test to get information about:

• Firmware version, emulation, codepage, sensor settings, interface settings, etc.

If no issues are found with the diagnostic test, examine other devices and software. The diagnostic test is working independently of devices and software.

Motor protection from being overheated
To prevent the motor from overheating, stop the printer for at least 30 seconds after continuously printing 1.5 meters.

Peripheral Connection

This product can communicate with other devices via Bluetooth, Wi-Fi, or a communication cable.

Bluetooth Connection Optional

1. The Printer can be connected to devices equipped with Bluetooth communication capabilities (PDAs, PCs, etc.).
2. Use the Bluetooth connection function supported by your device to connect to the printer.

NOTE

• This model supports Numeric Comparison function.
• Please refer to the configuration manual for details.

Wi-Fi Connection Optional

1. The Printer can be connected to devices equipped with Wi-Fi communication capabilities (PDAs, PCs, etc.).
2. Use the Wi-Fi connection function supported by the device to connect to the printer.

NOTE

• Please refer to the configuration manual for details.

NFC Connection Optional
The printer can be connected to devices equipped with NFC communication capabilities.

Use the NFC connection function supported by the device to connect to the printer.

NOTE

• Please refer to the configuration manual for details.
• NFC is only compatible with Bluetooth.

Interface Cable Connection

1. Flip over the connector cover and connect USB cable to the printer connector.
   NOTE Only use cables included with the printer. (USB)

2. Connect the interface cable to the USB port of the device (PDA, PC, etc.).

Cleaning the Printer

If the interior of the printer is dusty, printing quality can be reduced. In this case, follow the instructions below to clean the printer.

NOTE

1. Make sure to turn the printer power off prior to cleaning.
2. Regarding printhead cleaning, as the printhead gets very hot during printing, turn off the printer power and wait approximately 10 minutes before cleaning.
3. When cleaning the printhead, take care not to touch the heated portion of the printhead. The printhead can be damaged by static electricity.
4. Take care not to allow the printhead to become scratched and / or damaged in any way.
5. Use an applicator swab moistened with an alcohol solution to clean the printhead and remove any dust.
6. Once the cleaning is completed, wait a few minutes before inserting the paper roll into the printer.
   Preventing Overheating
   To prevent the motor from overheating, stop the printer for at least 30 seconds after continuously printing 1.5 meters.

JAM Error

• When you face with a paper jam error, please press the button down to open the printer cover.
  CAUTION
  Make sure to be careful of the HOT head.

• Please remove the paper.
  NOTE
  Please make sure you hear the closing sound of the upper cover.

• NOTE
  If the cover is not shut down completely, the printer may not work properly

• After removing, close the cover. The printer will work normally.

Roll Media Specification

Core

Diameter (A)| 12.5 mm
Roll
Max.Diameter (B)| 50 mm
Max.Media Width (C)| 80 mm
Min.Media Thickness| 0.06 mm

Caution
Protect the printhead from sand, grit, and other hard particles during printing and storage. Keep the cover closed. Even very small foreign particles may cause severe harm to the printhead.

Black Mark

Printer Specification

Character

| FBoign5t)(AKF(O1R2×,tJ0P2N14),,CFHoNn-tGBB(293×121,7C),HANs-ian F,

DRown, looandab/le/2T/T4F/5, /F6o/n7t,AR~eHs,idFeonnttGTTS,

esidnt TTF(Font0), Font 1~8

Barcode

| 1D| ECI AoFNd, a-8bU,aErA,NCA8o((d++e21+15,),CEoAdNe-3193,,CEoAdNe1933(,+C2o+d5e),128,

PTlanLet,PUCP-C-A2e+t5c), UPC-E, UPC-E(+2+5),

2D| PDDatFa4m17a,trQixR,,AMztaexcic, oMdicer,oRPSDSF1441, 7TLC39,
Emulation| ESC/POS, CPCL, ZPL Command compatible
Driver| WC5.Ein&doMLwoi sbuiDlxeriDveriirv(XerPr, &~,SSDeKrv(eCrE2040.23~~, )M, WoDbinildeow

Ja0v~a)P, OSn DriDver rv,eiOSMSaDc KD,rAivnedr,roOiPdO(6S.0 ~r)vSeDr,K

Sensor| Black mark, Paper end

Paper

| Paper type| Thermal Receipt
Width| 80mm (PAPER GUIDE : 58mm)
Thickness| 0.06mm
RDoiallmMeatexr| Max. Ø 50mm
Roll Core| 12.5mm ± 0.5mm
Interface| Standard| USB
---|---|---
Option| WRei-aFdi(y8(0B2lu.1e1toa/obth/g4/.n2)+,BBLlEue+toNoFtCh TSamg)art
BChatatregreyr| Input| AC100~240V, 50/60Hz
Output| 8.4V , 800~1400mA

Battery

| Type| Li-ion
Output| 7.4V, 2000mAh
Charging time| 2.7Hrs (61Hrs stand-by)
Cutter| AMC(Advanced Manual Cutter)
Size (W x L x D)| 107.5 x 145 x 56 mm
IP| IP54
Weight| 422g (with Battery)
Temperature| Operation| -10 ~ 50℃
Storage| -20 ~ 60℃
Humidity| Operation| 10 ~ 80%
Storage| 10 ~ 90%

Utilities

The following utilities and concerned manual can be found on the QR or homepage.

1

|

PrinterGear

| Tphriinstiesrawnitihntbeeglroawtedtausktisli.ty that you can manage your

– Printer Configuration Settings

– Wireless-Lan Settings

– Font(Bitmap/TrueType) Download

– Printing service

– Document management

– FW Download

※- Maintenance o PrinterGear Manual for detailed

infPolremasaetiorenf.er t

2| LabelMaker(CPCL)| Tlahbieslpprroignrtainmg.is for label form design and designed
3| (SAenwdoroiMd _UUtitliiltiyty) (ESC/POS)| Iettcis. athurotiuligtyhaBplpuetthoaottphrainntds tWexi- tF,ibcaormcomdeusn,iicmataiognes, , and able to printer settings.

S/W
We provides SDK, Driver, etc. as follows to respond to various S/W usage environments. You can download this S/W from the homepage.

References

• SEWOO

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>