Stratasys TrueDent Cure Curing Chamber User Guide

: September 22, 2024
: stratasys

TrueDent Cure Curing Chamber

“`html

TrueDent Cure Curing Chamber

Specifications

Product: TrueDent Cure Curing Chamber
Technology: LED light and heat
Application: Curing 3D PolyJet printed parts
Warranty: Limited one-year warranty (or greater as required by
local law)
Compliance: FCC compliant

Product Overview

TrueDent Cure is a curing chamber that utilizes LED light and
heat to create an optimal environment for curing 3D PolyJet printed
parts.

Product Usage Instructions

Unpacking

When unpacking the TrueDent Cure, ensure all components are
present and in good condition. Refer to the user manual for
unpacking instructions.

Setup

Follow the step-by-step setup guide provided in the user manual.
Place the TrueDent Cure in a well-ventilated area away from direct
sunlight or heat sources.

Operation

Switch on the TrueDent Cure and select the appropriate operation
mode according to your curing requirements. Monitor the run screen
for progress updates.

Operation Modes

The TrueDent Cure offers different operation modes to cater to
various curing needs. Select the mode that suits your specific
requirements.

Run Screen

The run screen displays real-time information about the curing
process. Keep an eye on the screen for any alerts or
notifications.

Care and Maintenance

Regularly clean the TrueDent Cure chamber to ensure optimal
performance. Refer to the maintenance section in the user manual
for detailed cleaning instructions.

Spare Parts

Order genuine spare parts from authorized dealers or directly
from Stratasys to maintain the TrueDent Cure’s functionality.

Storage and Transportation

When not in use, store the TrueDent Cure in a cool, dry place
away from dust and direct sunlight. Use appropriate packaging if
transporting the unit.

FAQ

Q: What should I do if the LED lamps need replacement?

A: LED lamps are considered consumable items and are not covered
under the warranty. Contact Stratasys for genuine replacement LED
lamps.

Q: Is it safe to touch the printer surfaces during

operation?

A: Avoid touching hot surfaces of the printer during operation
to prevent burns or discomfort. Exercise caution when performing
maintenance near hot surfaces.

“`

TrueDentTM Cure Curing Chamber

Product Guide

DOC-09141 Rev. D

TrueDent Cure Product Guide
Copyright
© Copyright 2024 Stratasys. All rights reserved. This documentation contains proprietary information of Stratasys Ltd. This information is supplied solely to assist authorized users of this cleaning system. No part of this document may be used for other purposes, and it may not be disclosed to other parties. The specifications on which this document is based are subject to change without notice. No part of this book may be reproduced in any form or by any means, nor stored in a database or retrieval system, without prior permission in writing from Stratasys Ltd. If this document is distributed as a PDF file, you may print it for internal use. DOC-09141 Rev. D
Trademark
Stratasys, Stratasys logo, Objet, PolyJet, and TrueDent Cure are trademarks of Stratasys Ltd. and/or its subsidiaries or affiliates and may be registered in certain jurisdictions. All names of product names and trademarks are the property of their respective owners.
Liability
Stratasys shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. Stratasys makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. It is the responsibility of the system owner/material buyer to determine that Stratasys material is safe, lawful, and technically suitable for the intended application as well as identify the proper disposal (or recycling) method consistent with local environmental regulations. Except as provided in Stratasys’ standard conditions of sale, Stratasys shall not be responsible for any loss resulting from any use of its products described herein.
Disclaimer
Customer acknowledges the contents of this document and that Stratasys parts, materials, and supplies are subject to its standard terms and conditions, available on https://www.stratasys.com/legal/terms-and-conditions-of-sale, which are incorporated herein by reference.
Stratasys Ltd. www.stratasys.com Comments: c-support@stratasys.com

Page 2

TrueDent Cure Product Guide

Contents

Contents
Contents……………………………………………………………………………. 3 Overview …………………………………………………………………………… 4 Warranty……………………………………………………………………………. 4 Compliance ……………………………………………………………………….. 4 Safety ……………………………………………………………………………….. 4
Hazardous Situations During Use………………………………………………………………. 5
Specifications …………………………………………………………………….. 5 Unpacking …………………………………………………………………………. 6 Setup………………………………………………………………………………… 7 Operation ………………………………………………………………………….. 7
Operation Modes …………………………………………………………………………………….. 7 Run Screen …………………………………………………………………………………………….. 8
Care and Maintenance………………………………………………………… 9 Spare Parts ……………………………………………………………………….. 9 Storage and Transportation………………………………………………….. 9

Page 3

TrueDent Cure Product Guide

Overview

Overview
TrueDent Cure is a curing chamber. It uses LED light and heat to provide an ideal environment suitable for curing 3D PolyJet printed parts.

Warranty
TrueDent Cure has a limited one-year warranty (or greater when required by local law) that covers everything except the LED lamps, which are considered consumable items. Details on the warranty can be found in the legal section of the Stratasys website:
https://www.stratasys.com/legal/system-warranty-period https://www.stratasys.com/legal/terms-and-conditions-of-sale

Compliance
This product is FCC compliant.

Safety
Read these important safety guidelines before using this product.
· This product is intended for curing 3D printed parts. Do not use this product for any other purpose as the safety of the product cannot be ensured.
· Do not put flammable liquids in the chamber. Allow any solvents on the printed parts to completely evaporate before placing them in the chamber. Flammable fluids in the chamber create a risk of fire and/or explosion.
· Do not place items on or around this product to maintain unblocked airflow. Keep flammable liquids away from this product. Do not put liquids on top of the product, as a spill could create a risk of electric shock.
· Do not look at the lamps without appropriate eye protection. This product is equipped with a safety interlock that turns off the lamps when the door is opened.
· The door handle reaches to approximately 60°C during operation. Wear heat- resistant gloves when opening the door.
· Should this product malfunction in any way, immediately unplug it and contact your regional service provider. Do not continue to operate a malfunctioning unit, as damage or even injury may occur.
· If you have any questions about the setup, use, or care of this product, please contact your regional service provider.

Page 4

TrueDent Cure Product Guide

Specifications

Hazardous Situations During Use

Symbols

Meaning and Actions

Danger of Hot Surfaces! During operation, the surfaces of the printer become hot and can cause burns or discomfort when directly touched. Exercise care when performing maintenance on or near hot printer surfaces.

If hot surfaces are to be accessed, or work near hot surfaces is required, the following personal protective equipment must be used:

Wear Heat-Resistant Protective Gloves

Wear heat-resistant protective gloves where it is necessary to handle hot items or surfaces.

Specifications

Power Input 115V unit Power Input 220V unit Frequency Ambient Temperature Heat-up Time to Maximum Temperature Relative Humidity LED Output LED Wavelength (Typ) Unit Size Chamber Size Unit Weight Shipping Size Shipping Weight

110120V 220240V 5060 Hz 1825C / 64.477F
3045 minutes
3070% (non-condensing) 9 Watts per lamp (x 4) 450460 nm per lamp (x 4) 30.5 x 30.5 x 26 cm / 12 x 12 x 10.25 in. 30.5 x 30.5 x 16 cm / 12 x 12 x 6.25 in. 10 kg / 22 lbs 41 x 41 x 36 cm / 16 x 16 x 14 in. 11.4 kg / 25 lbs

Page 5

TrueDent Cure Product Guide

Unpacking

Unpacking
· Open the packaging carefully and store it for future use. Original packaging is required should this product need warranty repair or replacement.
· This product is shipped in two boxes, a box within a box, to ensure it arrives undamaged. It is recommended to unpack with 2 people.
1. Open the top flaps of the outer box. 2. Remove the foam corner protectors, and keep them for future use. 3. Remove the power cord from the box.

Verify that the plug is suitable for your location. If not, purchase a cable locally.

4. Remove the inner box. 5. Open the inner box top flaps. 6. Remove, read, and keep the Important insert for reference. 7. Remove the product from the inner box. 8. Remove the product from the protective bag. Hold the door to prevent it from opening while
removing the product from the box. 9. Place the product on a stable work surface. 10. Slide the plastic shipping supports out from under each of the LED lamps.
Figure 1: LED lamp shipping support

11. Return packaging materials to the outer box and store them for future use, if necessary.

Page 6

TrueDent Cure Product Guide

Setup

Setup
1. Verify that the power switch is in the off (0) position. 2. Insert the power cord into the power inlet at the back of the unit. 3. Plug the power cord into a power outlet.

Operation
Switch on (I) the power switch on the back panel. The power switch has a red light when on, and the display screen turns on.
Operation Modes
This product has the following operation modes: · Preset modes – not used for PolyJet materials. · Custom mode – used for parts printed with PolyJet printers.
To cure the parts:
1. Prepare the parts as described in the TrueDent Best Practice document, available on the Stratasys Support Center.
2. Place the container(s) with the parts in the chamber. 3. Close the door. 4. Select Custom from the menu on the display.
Figure 2: Operation modes

Custom mode

Page 7

TrueDent Cure Product Guide

Operation

5. On the custom setting screen, use the up and down arrows to set the time and temperature according to the TrueDent Best Practice document. Tap and hold the arrows to move quickly through the ranges.
Figure 3: Custom screen

6. When the settings are adjusted as needed, tap Run. 7. Cure the parts as described in the TrueDent Best Practice document. When the selected time is reached, the LEDs and heat turn off automatically.
Warning: Hot Surface Hazard The door handle can reach a temperature of approximately 60ºC during operation, and could cause injury. Do not touch the product or open the door before wearing heat resistant gloves.

Run Screen
The Run screen displays the settings and status of the product. Figure 4: Run screen

1

2

3

4

5

Component

1 Status of the door, lamps, and heater

2 Selected program time and temperature settings

3 Process time remaining and chamber temperature

Component

4 Pauses the process until you tap Resume

5 Stops the process and returns you to the main screen

Page 8

TrueDent Cure Product Guide

Care and Maintenance

Care and Maintenance
This product is almost maintenance free, but it is recommended to keep the reflective surfaces clean to allow sufficient light to the parts. The preferred materials for cleaning the interior and exterior surfaces are mild detergent and water. Follow the following guidelines: · Before cleaning, unplug the product from the electrical outlet. · Use a soft cloth dampened (not dripping) with soapy water. · Do not soak the this product in water or other liquids. · Wipe surfaces until clean, and then rinse with a clean cloth dampened with clean water. · For resin residue, use isopropyl alcohol. If isopropyl alcohol is used, allow it to evaporate
with the door open before connecting this product to power. · You can use general purpose household cleaners, such as 409®, Fantastik®, or Windex®
for the reflective surfaces. · Be careful when cleaning the LexanTM work surface inside the chamber not to allow excess
cleaning product to run over the edges where it would be impossible to wipe clean. · When all surfaces are dry it is safe to reconnect the product to the electrical outlet.
Do not use harsh solvents like acetone, MEK, Toluene, etc. They will damage the product. When in doubt, contact your regional service provider.
· Replace the 4 LED lamps after 800 hours of lamp use.

Spare Parts
1 set of 4 lamps is provided for spare parts.
This product is not user-serviceable, except for the LED lamps. Replacement LED lamps are available for purchase from your distributor or directly from our web store. Should something break, refer to the warranty section of this guide. If your unit is not covered by the warranty, contact your regional service provider for help.

Storage and Transportation
If it is necessary to transport or store this product, the following will ensure the safety of the device: 1. Turn off the power switch. 2. Unplug the product from the power. 3. Wipe the inside and outside of the product with mild detergent and water or isopropyl
alcohol to remove excess resin and other debris.

Page 9

TrueDent Cure Product Guide

Storage and Transportation

4. Ensure the chamber is empty.

It is not necessary to remove the LED lamps for storage or transportation.

5. Place the product in the packing bag (optional).
6. Reinstall the protective foam end caps that originally shipped with the product onto the left and right sides of this product.
7. Slide the bagged product with the end caps into the original boxes. Keep the product upright.
8. Place the power cord in the open space created by the protective foam end caps.
9. Close the top of the boxes using reinforced paper tape (preferred) or clear adhesive shipping tape (if you do not have access to reinforced paper tape). Tape all box seams.
10. Store and transport the product in the upright position.

Page 10

www.stratasys.com

THE 3D PRINTING SOLUTIONS COMPANY