Woodpeckers Super Fence Micro Adjust Kit Owner’s Manual

: September 23, 2024
: Woodpeckers

Table of Contents

Super Fence Micro Adjust Kit
Woodpeckers Micro-Adjust
Specifications:
Product Usage Instructions:
Installation:
Usage:
- FAQ:
Q: What should I do if I think I’m missing parts?

Super Fence Micro Adjust Kit

“`html

Woodpeckers Micro-Adjust

Specifications:

Product: Woodpeckers Micro-Adjust
Manufacturer: Woodpeckers
Made in: USA
Model: Micro-Adjust
WARNING: This product contains chemicals, including chromium,
known to the State of California to cause cancer and birth defects
or other reproductive harm. For more information, visit www.P65Warnings.ca.gov

Product Usage Instructions:

Installation:

Install the (4) long screws through the main block and start
oval nuts from the bottom.
Install the (2) short screws and washers through the fence
mounting plate. Start oval nuts on these two as well.
Attach the main block to the top of the track by sliding oval
nuts into the slots and tighten all four screws.
Insert two hex bolts up through the holes in the track, place
nylon washers over each bolt, and start each knob.
Slide the fence toward the back of your router table, position
the main block just off the table, align the oval nuts, and slide
the Micro Adjust assembly until centered with the fence.
Align bolt heads below the track with track slots in the table
when sliding both the Micro Adjust and fence toward the center of
the table.
Tighten the two clamping knobs once Micro Adjust is flush with
the back of the table and centered to the fence.

Usage:

Before routing, tighten both fence clamping knobs and both
Micro Adjust clamping knobs.
To fine-tune the position of the router fence, loosen the fence
clamping knobs, adjust using the adjustment knob, and
re-tighten.

FAQ:

Q: What should I do if I think I’m missing parts?

A: If you believe you are missing any components, please contact
us via email at mailroom@woodpeck.com or call us at 800-752-0725
during our business hours from 9:00 a.m. to 5:00 p.m. EST, Monday
to Friday.

“`

Woodpeckers
MICRO-ADJUST
OWNER’ S MANUAL
These instructions explain how to install the Micro Adjust accessory to the Woodpeckers Super Fence.
Begin by installing the (4) long screws down through the main block. Loosely start the oval nuts from the bottom. Next install the (2) short screws and washers through the fence mounting plate as shown. Loosely start oval nuts on these two as well.
If you think you’re missing anything, email us at mailroom@woodpeck.com. You can also call us at 800-752-0725 from 9:00 a.m. to 5:00 p.m. EST Monday – Friday.

Attach the main block to the top of the track (2-slot face) by sliding all four oval nuts into the slots. With the main block approximately centered, tighten all four screws.
Now insert the two hex bolts up through the two holes in the track. First slip a nylon washer over each bolt then loosely start each knob.

Before attaching the Micro Adjust to the back of your fence, slide the fence toward the back of your router table so the main block is positioned just off the table. Now align the front two oval nuts with the slot toward the bottom, back of the fence. With these two oval nuts fully engaged in the slot, slide the entire Micro Adjust assembly until it’s approximately centered with the fence. Just barely tighten the screws.

Once the fence Micro Adjust is approximately centered on the fence, slide both it and the fence toward the center of the table. During this step you need to align the bolt heads below the track with the track slots in the table.
Once the Micro Adjust is flush with the back of the table and centered to the fence, tighten the two clamping knobs.
To fine tune the position of the router fence itself, make sure the two clamp knobs holding the fence are loosened. Then turn the adjustment knob to move the fence and finally re-tighten the fence clamping knobs. Also make sure the Micro Adjust clamping knobs are tight.
BEFORE ROUTING WITH YOUR FENCE, YOU MUST TIGHTEN THETWO FENCE CLAMPING KNOBSAND THE TWO MICRO ADJUST CLAMPING KNOBS.
Woodpeckers®
PRECISION WOODWORKING TOOLS MADE IN USA
Woodpeckers, LLC Strongsville, Ohio · Woodpeck.Com
© 2019 Woodpeckers, LLC
WARNING! This product can expose you to chemicals, including chromium, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

REV012919