Stanley SL18910P-3 3-GALLON WET-DRY VACUUM OWNER’S MANUAL
- September 20, 2024
- Stanley
Table of Contents
Stanley SL18910P-3 3-GALLON WET-DRY VACUUM
PRODUCT SPECIFICATIONS
| Model | SL18910P-3 |
|---|---|
| Power | 120 V / 60 Hz / 8A |
| Motor | Single Stage |
| Tank Capacity | 3 Gallon |
| Hose | 1-1/4 in. x 4 ft. |
| Power cord | SJTW18AWG / 6 ft. Length |
WARNING:
Extension cords in poor condition or that are too small in wire size can pose
fire and shock hazards. To reduce the risk of these hazards when using an
extension cord, be sure it is in good condition and that the connection does
not come into contact with liquid. To keep power loss to a minimum, use the
following table to choose the minimum wire size extension cord.
| Extension Cord | Length | Gauge | A.W.G. |
|---|---|---|---|
| 0 – 50 ft. | 14 | ||
| 50 – 100 ft. | 12 |
PACKAGE CONTENTS
| PART DESCRIPTION | QTY |
|---|---|
| A | Handle |
| B | On/Off switch |
| C | Power cord |
| D | Vacuum port |
| E | Dust tank |
| PART | DESCRIPTION |
| --- | --- |
| F | Reusable cloth dry filter |
& Mounting ring
| 25-1201| 1
G| Gulper nozzle| 13-1588| 1
H| 3 in 1 Crevice nozzle| 13-1513| 1
I| Foam filter| 25-1202| 1
J| 4ft × 1-1/4 in hose| 20-1300| 1
SAFETY INFORMATION
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions should be always
followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS
APPLIANCE.
ATTENTION!
Read all safety rules carefully before attempting to operate. Retain for
future reference.
DANGER!
Never operate this unit when flammable materials or vapors are present because
electrical devices produce arcs or sparks that can cause a fire or explosion.
NEVER LEAVE THE OPERATING VACUUM UNATTENDED!
WARNING!
To reduce the risk of fire, electric shock, or injury:
-
Do not leave appliance when plugged in. Unplug from outlet when not in use and before servicing.
-
Use indoors only.
-
Always disconnect the plug from the wall outlet before removing the tank cover.
-
Do not allow to be used as a toy. Close attention is necessary when used by or near children.
-
Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped,\ damaged, left outdoors or dropped into water, contact service center for assistance.
-
Do not: pull or carry by cord, use cord as a handle, close a door on cord or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.
-
Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
-
Do not handle plug or appliance with wet hands.
-
Do not put any object into openings. Do not use with any openings blocked; keep free of dust, lint, hair and anything that may reduce air flow.
-
Keep hair, loose clothing, fingers and all parts of body away from openings and moving parts.
-
Do not pick up anything that is burning or smoking, such as cigarettes, matches or hot ashes.
-
Do not use without dust bag and/or filters in place.
-
Turn off all controls before unplugging.
-
Use extra care when cleaning on stairs.
-
Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they may be present.
-
Do not use your cleaner as a sprayer of flammable liquids such as oil-based paint, lacquers, etc.
-
Do not vacuum toxic, carcinogenic, combustible or other hazardous materials such as asbestos, arsenic, barium, beryllium, lead, pesticides or other health endangering materials.
-
Do not pick up soot, cement, plaster or drywall dust without filter and dust bag in place. These are very fine particles that may affect the performance of the motor or be exhausted back into the air. Additional dust bags are available.
-
Do not leave the cord lying on the floor once you have finished the cleaning job. It can become a tripping hazard.
-
Use special care when emptying heavily loaded tanks.
-
To avoid spontaneous combustion, empty tank after each use.
-
The operation of a utility vac can result in foreign objects being blown into eyes, which can result in eye damage. Always wear safety goggles when operating a vacuum.
-
STAY ALERT. Watch what you are doing and use common sense. Do not use a vacuum cleaner when you are tired, distracted or under the influence of drugs, alcohol or medication causing diminished control.
NOTE: Use only as described in this manual. Use only the manufacturer’s recommended attachments. -
This appliance is provided with double insulation. Use only identical replacement parts. See instructions for servicing double insulated appliances Unplug before connecting the hose, nozzle and the like.
-
This appliance is provided with double insulation.Use only identical replacement parts. See instructions for Servicing of Double-Insulated Appliances.
SAVE THESE INSTRUCTIONS FOR HOUSEHOLD USE ONLY
To reduce the risk of electric shock, this appliance has a polarized plug (one
blade is wider than the other). This plug will fit in a polarized outlet only
one way. If the plug does not fit fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified electrician to install the proper
outlet. Do not change the plug in any way.”
WARNING!
SERVICING OF DOUBLE-INSULATED WET/DRY VAC
In a double-insulated Wet/Dry Vac, two systems of insulation are provided instead of grounding. No grounding means is provided on a double-insulated appliance, nor should a means for grounding be added. Servicing a double- insulated Wet/Dry Vac requires extreme care and knowledge of the system and should be done only by qualified service personnel. Replacement parts for a double-insulated Wet/Dry Vac must be identical to the parts they replace. Your double-insulated Wet/Dry Vac is marked with the words “DOUBLE INSULATED” and the symbol O (square within a square) may also be marked on the appliance.
IMPORTANT!
- If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
- Remove the plug from the socket before performing maintenance. Before using the machine make sure that the frequency and voltage shown on the rating plate correspond with the mains voltage.
- Specifications and details are subject to change without prior notice. The accessories shown in the pictures may vary from model to model.
IMPORTANT SAFEGUARDS
The symbol on the product or packaging indicates that the product must not be
treated as domestic refuse. Instead, it should be handed into a collection
point for the recycling of electrical and electronic components. By ensuring
the product is treated correctly, you will help prevent any negative impact on
the environment and health that might arise were the product to be discarded
as ordinary refuse. For further information about recycling, you should
contact your local authorities, refuse collection service or the sales outlet
where you bought the goods.
WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
ASSEMBLY
OPERATING INSTRUCTIONS
WARNING:
To reduce the risk of fire or explosion, do not operate this vac in areas with
flammable gases, vapors or explosive dust in the air. Flammable gases or
vapors include but are not limited to lighter fluid, solvent-type cleaners,
oil-based paints, gasoline, alcohol or aerosol sprays. Explosive dusts include
but are not limited to coal, magnesium, aluminum, and grain or gunpowder. Do
not vacuum explosive dust, flammable or combustible liquids, or hot ashes. Do
not use this vac as a sprayer for any flammable or combustible liquid. To
reduce the risk of health hazards from vapors or dust, do not vacuum toxic
materials.
WARNING:
The operation of any utility vac can result in foreign objects being blown
into the eyes, which can result in severe eye damage. Always wear safety
eyewear complying with ANSI 287.1 (or in Canada, CSA Z94.3) before starting
operation.
CAUTION:
To reduce the risk of hearing damage, wear ear protectors when using the vac
for extended hours or when using it in a noisy area.
This 3-gallon wet/dry vac is assembled at the factory and ready for use when
you remove it from the carton. The unit is ready for dry vacuuming or blowing.
After you plug the power cord into the wall receptacle, turn the unit “ON” by
pushing the switch from position “O” to position “I”. The “O” is the “OFF”
position and the “l” is the “ON” position.
ASSEMBLE THE HANDLE
Please install the handle as shown picture.
DRY PICK-UP
- Slide cloth filter over lide cage (Picture 1).
- If you use your vacuum to pick up dust when the filter is wet, the filter will clog quickly and be very difficult to clean.
- Attach power head to the tank and your vacuum is ready to use.
WET PICK-UP
-
Remove the reusable filter and replace it with a foam filter when you do wet pickups.
-
This wet/dry vac is equipped with a float mechanism which will rise automatically to cut off the airflow when the liquid in the tank reaches a predetermined level. When this happens, turn off the vac, unplug the power cord, and empty the dust tank. You will know that the float has shut the airflow off because the suction ceases and the motor noise becomes higher in pitch due to increased motor speed. The liquid capacity may vary with the rate of pickup.
IMPORTANT: 1. To reduce the risk of damage to the vac, do not run the motor with a float in the raised position. -
Wet pick-up accessories should be washed periodically after picking up wet, sticky kitchen accidents. This can be accomplished with a warm solution of soap and water.
EMPTY THE TANK
WARNING: To reduce the risk of injury from accidental starting, unplug the power cord before emptying the dust tank.
- Remove the power head assembly of the wet/dry vac by pulling outward on the lid clips located on each side of the vac. Lift off the power head assembly.
- Dump the tank contents into the proper waste disposal container.
BLOWING OPERATION
WARNING: Always wear safety eyewear complying with ANSI Z87.1 (or in
Canada CSA Z94.3) when using it as a blower.
WARNING: To avoid injury to bystanders, keep them clear of blowing
debris.
CAUTION: Wear a dust mask if blowing creates dust that might be inhaled.
CAUTION: To reduce the risk of hearing damage, wear ear protectors when
using the vac/blower for extended hours or when using it in a noisy area.
Your vac contains a blowing feature. It has the capability to blow sawdust and other debris. It can be used to blow dust and debris out of garages or off patios and driveways. Follow the steps below to use your vac as a blower.
- Locate the blowing port on your vac.
- Insert one end of the 1-1/4 in. x 4 ft. hose into the blowing port.
- Turn vac “ON”
CARE AND MAINTENANCE
FILTER REPLACEMENT
WARNING: To reduce the risk of injury from accidental starting, unplug the power cord before changing or cleaning the filter.
Your filter should be cleaned often to maintain peak vac performance.
IMPORTANT: To avoid damage to the blower wheel and motor, always reinstall the reusable filter before using the vac for dry pickups and always reinstall the foam filter before using the vac for wet pickups.
IMPORTANT: After cleaning, check the filter for tears or small holes. Do
not use a filter with holes or tears in it. Even a small hole can cause a lot
of dust to come out of your vac. Replace it immediately.
NOTE: Before installing the filter on the vac, clean the area of the lid
so that the clamp ring will seal the bag against the lid and stop small
particles from bypassing the filter bag. If the filter is clean and not
damaged, replace it on the filter cage. If it cannot be reused, place a new
filter over the filter cage.
NOTE:
Clean the filter in an open area. Cleaning should be done outdoors and not in
living quarters.
WARNING: Do not remove filter cage and float. The float prevents water from entering the impeller and damaging the motor. The cage prevents fingers from touching the moving impeller.
CLEANING
To keep your wet/dry vac looking its best, clean the outside with a cloth
dampened with warm water\ and mild soap.
To clean the tank:
- Dump out debris.
- Wash tank thoroughly with warm water and mild soap.
- Wipe out with dry cloth.
STORAGE
Before storing your vac, the dust tank should be emptied and cleaned. The cord
should be wrapped and hung on the unit and the accessories should be kept in
the accessory holder so they can be readily available. The vac should be
stored indoors.
TROUBLESHOOTING
WARNING!
TO REDUCE THE RISK OF INJURY FROM MOVING PARTS AND/OR ELECTRICAL SHOCK, TURN POWER SWITCH OFF AND DISCONNECT GROUNDED PLUG FROM ELECTRICAL OUTLET BEFORE PERFORMING TROUBLESHOOTING CHECKS.
Minor problems often can be fixed without calling customer service.
| PROBLEM | POSSIBLE CAUSE | CORRECTIVE ACTION |
|---|---|---|
| Vacuum will not run | No electricity | Make sure electrical outlet has voltage |
(A qualified electrician may need to be contacted)
Loss of suction, wet pick-up| 1. Full tank
2. Clogged hose
3. Clogged filter
| 1. Drain and clean tank
2. Remove hose and clean debris
3. Clean or replace filter
Loss of suction, dry pick-up| 1. Full tank
2. Clogged hose
3. Clogged filter
| 1. Drain and clean tank
2. Remove hose and clean debris
3. Clean or replace filter
EXPLODED VIEW / PARTS LIST
PART| DESCRIPTION| QTY| | PART| DESCRIPTION|
QTY
---|---|---|---|---|---|---
1| Handle| 1| | 6| Power cord| 1
2| On/Off switch| 1| | 7| Motor base| 1
3| Top cover| 1| | 8| Filter cage| 1
4| Baffle| 1| | 9| Dust tank| 1
5| Motor| 1| | 10| Vacuum port| 1
WARRANTY
Alton Industry Ltd.Goup 1-year Limited Warranty
This warranty covers any defects in materials or workmanship of the enclosed product. Alton Industry Ltd. Group will repair or replace any defective materials due to the craftsmanship of the product. This warranty does not cover any problem caused by misuse, abuse, accidents, or acts of God, such as floods or hurricanes. Consequential and incidental damages are not covered under this warranty. Coverage terminates if you sell or otherwise transfer the ownership. If you feel you have a defective product, please submit a copy of your receipt to the address below and call 1-888-899-0146 for instructions prior to returning this item to the store or sending it back to:
- Alton Industry Ltd. Group 1031 North Raddant Rd Batavia, Illinois 60510
We will inspect the product and contact you within 72 hours to give you the results of our inspection. We reserve the right to repair or replace the product at our discretion. However, we may replace the product with one of similar but not exact features. Parts and Service Information available call Alton Industry at 1-888-899-0146 This warranty gives you specific legal rights. You may have other rights which vary from state to state.
Stanley® and are trademarks of Stanley Black & Decker, Inc., or its affiliates and are used under license by Alton Industry Ltd. Group
The Stanley Black & Decker, Inc. New Britain, CT 06053 U.S.A
http://www.stanleyblackanddecker.com
FAQs
What is the capacity of the Stanley SL18910P-3?
The Stanley SL18910P-3 has a capacity of 3 gallons, making it suitable for a variety of cleaning tasks.
What type of power source does the Stanley SL18910P-3 use?
The Stanley SL18910P-3 operates using a corded electric power source, ensuring consistent performance.
What kind of motor does the Stanley SL18910P-3 have?
The Stanley SL18910P-3 is equipped with a 3 peak horsepower motor, providing powerful suction for both wet and dry cleanup.
What filters are included with the Stanley SL18910P-3?
The Stanley SL18910P-3 comes with a foam filter for wet pickup and a reusable dry filter, both of which are washable.
What accessories are included with the Stanley SL18910P-3?
The Stanley SL18910P-3 includes a 6-foot power cord, a 4-foot hose, a 3-in-1 crevice nozzle, and a gulper nozzle.
What is the weight of the Stanley SL18910P-3?
The Stanley SL18910P-3 weighs approximately 10 lbs, making it easy to maneuver and transport.
How long is the power cord on the Stanley SL18910P-3?
The power cord on the Stanley SL18910P-3 is 6 feet long, providing ample reach for various cleaning tasks.
What is the recommended voltage for the Stanley SL18910P-3?
The Stanley SL18910P-3 operates at a voltage of 120 volts (AC), suitable for standard household outlets.
How do you maintain the filters of the Stanley SL18910P-3?
The filters of the Stanley SL18910P-3 are washable and reusable; regular cleaning will help maintain optimal suction.
What surfaces can the Stanley SL18910P-3 be used on?
The Stanley SL18910P-3 is suitable for various surfaces, including upholstery and car interiors.
Can the Stanley SL18910P-3 be used for car cleaning?
Absolutely! The Stanley SL18910P-3 is ideal for cleaning cars, thanks to its portability and included accessories like the crevice nozzle.
How do you empty the tank of the Stanley SL18910P-3?
To empty the tank of the Stanley SL18910P-3, simply detach the tank and pour out the contents, ensuring it’s done safely and efficiently.
Download this Manual:Stanley SL18910P-3 3-GALLON WET-DRY VACUUM OWNER’S MANUAL
Reference Link
Stanley SL18910P-3 3-GALLON WET-DRY VACUUM OWNER’S MANUAL-Device. report
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>