LEDWOOD XTREME300 Wireless Speakers User Guide
- September 20, 2024
- LEDWOOD
Table of Contents
LEDWOOD XTREME300 Wireless Speakers
Download the manual though scanning the QR code.
ACCESSORIES
SAFETY INSTRUCTIONS
Please read this manual carefully, as it contains important information on installation and use of the unit. appliance during operation.
- Do not place naked flames on the unit.
- The unit is intended for use in temperate climates. The ambient temperature must not exceed exceed 40°C. Do not operate the unit at higher temperatures.
- In the event of a malfunction, switch off the unit immediately. Never attempt to repair the unit yourself. Improper repairs may result in damage or malfunction. Contact an authorized service center.
- Supervise children to ensure that they do not play with the device.
INSTRUCTIONS FOR BUILT-IN BATTERIES
- Batteries must not be exposed to excessive heat, such as sunshine, fire or similar sources. Risk of explosion, fire or fire hazard!
- Do not open the product
- Stay close when recharging. In the event of extreme heat, interrupt the process immediately and contact your dealer.
CLASS III EQUIPMENT
Safety extra-low voltage (SELV) or protective low voltage (PLV) power supply,
ungrounded masses, safe power supply (safety transformer).
Features
Bluetooth
Charging
CAUTION:
If the product is to be left unused for a long time, leave the battery fully
charged, otherwise the battery may be damaged! Do hot expose you device to
extreme temperatures (above 50°C) (e.g. direct sunlight in a closed vehicle,
near a heat source or radiator, etc.). High temperatures can damage the
speaker’s and reduce battery life.
Product Overview
- AUX 3.5 mm audio input
- USB input
- Reset
- USB-C power alimentation
CHARGING INSTRUCTIONS
- Connect the USB Type C cable to the « USB-C» connector (4), then to a USB socket or the mains supply via an AC adapter (not supplied). Once the battery is fully charged (approx. 5 hours), disconnect the cable.
- Press hold the main power button (7) to switch on the product.
PAIRING AND BT CONNECTIVITY
- Press and hold the mains «POWER» button (7) to switch on the product.
- Activate the wireless audio function on your device (smartphone, tablet, etc.).
- Select «XTREME300» from the list of devices found.
( Note : the product automatically enters Bluetooth mode when switched on).
TWS FUNCTION
- Switch on both speakers and press the « TWS » (11) button on one of the speakers. The TWS button will continue to light up after successful paining.
- Activate your phone’s Bluetooth function and search for the pairing name. Establish the connection.
- Press the «TWS» (11) button to disconnect the TWS function.
3.5MM AUXILIARY CONNECTIVITY
Connect a 3.5mm AUX jack cable to the « AUX »input (1), the speaker will
automatically play the music
USING USB
Insert a USB key in the « USB » slot (2). the speaker will automatically play
the music
RGB LIGHT
The RGB light is on when the speaker is switched on. Simply press the «RGB»
button (8) to switch the light on/off.
HANDS-FREE FUNCTION
- Incoming call: Briefly press the «Play/Pause» button (6) to accept the call, or press and hold to reject the call.
- End call: Briefly press the «Play/Pause» button (6) or operate the cell phone to end the call.
TROUBLESHOOTING
No power supply: first check that the speaker is switched on. If this is the case, switch off the speaker, connect the power cable to the device after charging it or, once connected, leave the device switched on while charging Automatic shutdown: battery protection is automatically activated when the battery is low, so please use it after recharging for 5 hours.
No sound from the speaker when playback is activated
- A. Check that the AUX audio cable is correctly connected to the device and the sound source.
- B. Check that the volume is not set to minimum.
- C. Check that the correct signal source has been selected.
- D. Check that the audio source is not malfunctioning.
Unable to play music: the music file storage path cannot be recognized, save the file and store it in the root directory of the removable device. If the unit is jammed, insert a paper clip into the reset socket (3) on the back of the unit.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>