Afterglow 052-022 Wave Dual Charger User Guide

Afterglow 052-022 Wave Dual Charger

IN THIS QUICK START GUIDE

• Items Included with the Afterglow Wave Dual Charger
• Getting Started
  • Assembling the Charger
  • Connecting the Charger
  • Placing the Controller(s)
  • Charging in Rest Mode
• Lighting Features
• Connecting to Mobile app via Bluetooth button
  • Cycle through lighting profile via Profile button
• Troubleshooting
  • Controllers not charging
  • LED lighting not working

ITEMS INCLUDED

• Charging Base

• Base Stand

• USB-A to USB-C Cable

GETTING STARTED

1. Assembling the charger
   a. Locate the connection slots on the bottom of the charger.
   b. Take the stand and line up the slots of the charger and the stand.
   c. Slide in the stand. You should feel and hear a small click signaling that the stand is correctly attached.
   d. To remove the stand, simply push in and slide the stand out.

2. Powering the charger
   a. Connect the USB-C end of the included cable to the charging base.
   b. Connect the USB-A end of the included cable to the PlayStation®5 console.
   c. Your charger is now ready.

Please note the following:

  * The charger should never be plugged into anything other than the PS5® console. Plugging into other power sources, such as a wall outlet or PC may not properly charge your controllers.
  * The PS5® console must be turned on to charge your controllers. (See below for charging in Rest Mode.)
  * To efficiently charge your controllers please use the USB cable provided.  

3. Charging the Controllers
   a. To charge your controllers, place your DualSense® Wireless Controllersinto the slots of the charging base, connecting them to the charging pins.

   • The light bar on the controllers will begin to blink orange to indicate that they are charging. Once the controllers are completely charged, the orange light bar will turn off.

Note: The LED lighting effects DO NOT indicate charging.

4. Charging in Rest Mode
   To charge your controllers while your PS5® console is in Rest Mode follow the steps below. From the home screen, go to Settings > System > Power Saving > Features Available in Rest Mode > Set Supply Power to USB Ports to “Always or 3 Hours”.

LIGHTING FEATURES

1. The Afterglow Wave Dual Charger is equipped with 8 RGB zones and 5 programmable lighting profiles.

2. To customize lighting and more, please download the free PDP Control Hub mobile app.
   a. Add clickable Link to Apple Store
   b. Add clickable Link to Goggle Play Store

3. Connecting to the PDP Control Hub Mobile App
   a. If you have not yet downloaded the PDP Control Hub, please do so by following the link above.
   b. Once downloaded, launch the app.
   c. While the app is searching for a device, press and hold the Sync button located on the left side of the charger for 3 seconds.
   d. The charger will begin pairing to the mobile device. While in pairing mode, the LEDs around the charger will blink white.
   e. Once paired, the LEDs will return to their default state and the charger will be displayed in the app.
   f. If pairing fails, the LEDs will flash red and then return to their default or programmed state.
   g. Refer to the in-app guide for customized lighting.

4. Cycle through lighting profiles

   • By default, the charger has 5 pre-loaded LED profiles: Wave, Static, Breathing, Pulse, and Ripple.
   • To cycle through the saved lighting effects, press the profile button located on the right side of the charger.
   • Each LED profile can be customized in the PDP Control Hub mobile app.

TROUBLESHOOTING

1. Controllers not charging
   a. Make sure that the USB cable is plugged into the charger base and into the console
   i. If the charger is drawing power from a source other than the PS5® console, the controllers may not charge.
   b. Make sure that the controller is properly placed on the charger with the charging pins connecting to the controller.
   c. If the controllers are fully charged, then the controllers will not charge.

2. LED lighting not working
   a. The LEDs will be activated when a controller is placed on the charger, regardless of if the controller is being charged or not. If no controller is on the charger, then only the PDP logo will be illuminated.
   b. Please refer to the charger settings in the PDP Control Hub app.

“PlayStation”, “PS5”, “PS4”, and “PlayStation Shapes Logo (Gradated)” are registered trademarks or

  CUSTOMER SUPPORT

For:
Playstation 5®
Playstation 4® consoles
“PlayStation”, “PS5”, “PS4”, and “PlayStation Shapes Logo (Gradated)” are registered trademarks or trademarks of Sony Interactive Entertainment Inc

Official Licensed Product

Documents / Resources

| Afterglow 052-022 Wave Dual Charger [pdf] User Guide
052-022 Wave Dual Charger, 052-022, Wave Dual Charger, Dual Charger, Charger
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>