Afterglow F180060-A1 Outdoor Terra Fab Propane Fire Pit Table User Guide
- June 17, 2024
- AFTERGLOW
Table of Contents
- IMPORTANT SAFETY INFORMATION
- IMPORTANT SAFETY INFORMATION ABOUT PROPANE (LP) GAS
- SPECIFICATIONS
- PACKAGE CONTENTS
- ASSEMBLY INSTRUCTIONS
- NATURAL GAS CONVERSION
- BATTERY
- LEAK TEST
- LIGHTING INSTRUCTIONS
- TO TURN OFF GAS
- CARE AND MAINTENANCE
- REPLACEMENT PARTS LIST
- WARRANTY
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Afterglow F180060-A1 Outdoor Terra Fab Propane Fire Pit Table User Guide
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
DANGER
FIRE OR EXPLOSION HAZARD.
If you smell gas:
- Shut off gas to the appliance.
- Extinguish any open flame.
- If odor continues, leave the area immediately.
- After leaving the area, call your gas supplier or fire department.
Failure to follow these instructions could result in fire or explosion, which could cause property damage, personal injury, or death.
WARNING: For Outdoor Use Only.
Installation and service must be performed by a qualified installer, service
agency, or the gas supplier.
WARNING
Do not store or use gasoline, or other flammable vapors and liquids,in the vicinity of this or any other appliance.
An LP-cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.
DANGER
CARBON MONOXIDE HAZARD
This appliance can produce carbon monoxide which has no odor.
Using it in an enclosed space can kill you.
Never use this appliance in an enclosed space such as a camper, tent, car or
home.
WARNING:
If the information in this manual is not followed exactly, a fire or explosion
may result causing property damage, personal injury, or loss of life.
IMPORTANT SAFETY INFORMATION
- The installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1●NFPA 54; National Fuel Gas Code; Natural Gas and Propane Installation Code, CSA B149.1; or Propane Storage and Handling Code, CSA B149.2, as applicable.
- The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psi (3.5 kPa).
- The maximum inlet gas supply pressure is 250 psi.
- The appliance area must be kept clear and free from combustible materials, gasoline, and other flammable vapors and liquids.
- Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control that has been under water.
- Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid burns or clothing ignition.
- Young children should be carefully supervised when they are in the area of the appliance.
- Clothing or other flammable materials should not be hung from the appliance or placed on or near the appliance.
- Any guard or other protective device removed for servicing the appliance shall be replaced prior to operating the appliance.
- Installation and repair should be done by a qualified service person. The appliance should be inspected before use and at least annually by a qualified service person. More frequent cleaning may be required as necessary. It is imperative that the control compartment, burners, and circulating air passageways of the appliance are kept clean.
- CAUTION: The propane gas pressure regulator provided with this appliance must be used. This regulator is set for an outlet pressure of 11 inches water column.
- DO NOT burn solid fuels in this appliance.
- This outdoor gas appliance is for Outdoor Use ONLY.
- This outdoor gas appliance is not intended to be installed in or on recreational vehicles and/or boats.
- This outdoor appliance is not for use on wood decks or other flammable surface.
- Before each use of this gas appliance, open the door and/or the LP (Liquid Propane) Tank Drawer and inspect the hose. If there is evidence of excessive abrasion or wear or if the hose is damaged, the hose assembly must be replaced prior to the appliance being put into operation. Use only the replacement hose assembly specified in this manual. Make sure to leak test.
- Before each use of this gas appliance, inspect the burner. The burner must be replaced prior to the appliance being put into operation if it is evident that the burner is damaged. Use only the replacement burner specified in this manual.
- Make sure to properly locate the gas hose including locating the hose out of pathways where people may trip over it or in areas where the hose may be subject to accidental damage.
- Keep the fuel supply hose away from any heated surface.
- Never use this appliance closer than 10 feet from anything flammable, including houses or overhead tree branches.
- Never use gasoline, kerosene, or any other liquid fuel to start a fire.
- Always maintain a safe distance from the fire.
- Always supervise children around the fire.
- Never leave a fire unattended.
- The appliance is hot during and after use, always allow ample cooling time before touching or moving.
IMPORTANT SAFETY INFORMATION ABOUT PROPANE (LP) GAS
- The LP-gas supply cylinder to be used must be constructed and marked in accordance with the U.S. Deparment of Transportation (D.O.T.) Specifications for LP-Gas Cylinders, or the Standard for Cylinders, Spheres and Tubes for Transportation of Dangerous Goods and Commission, CAN/CSA-B339, as applicable.
- The LP-gas supply cylinder to be used must have a listed overfilling prevention device (See Figure 1).
- The LP-gas supply cylinder to be used must have a cylinder connection device compatible with the connection for the appliance.
- A self-contained LP-gas cylinder for use with this appliance must have a capacity of 20 Ibs cylinder (Height approximately 18 in., Tank Body approximately 12 in. diameter, Base approximately 8 in. diameter).
- The cylinder supply system must be arranged for vapor withdrawl.
- The cylinder used must include a collar to protect the cylinder valve.
- This appliance shall be used only outdoors in a well-ventilated space and shall not be used in a building, garage or any other enclosed space.
- When this appliance is not in use, the gas must be turned off at the supply cylinder.
- Storage of this appliance indoors is permissible only if the cylinder is disconnected and removed from the appliance.
- Cylinders must be stored outdoors in a well-ventilated area out of the reach of children.Disconnected cylinders must have threaded valve plugs tightly installed and must not be stored in a building, garage or anyother enclosed areas.
- This appliance is certified by CSA (Canadian Standards Association) to ANS Z21.97 CSA 2.41-2017, Outdoor Decorative Gas Appliances.
Standard 20 Ib.tank Figure 1
SPECIFICATIONS
Rated Heat Input (Liquid Propane & Natural Gas) | 50,000 BTU/hr |
---|---|
Propane Regulator Pressure | 11 inches water column |
Natural Gas Inlet Pressure | 7 inches water column |
Clearance to combustible surfaces | Sides: 24in. (610mm), Top: 72in. (1829mm) |
PACKAGE CONTENTS
PART | DESCRIPTION | QUANTITY |
---|---|---|
A | F ire Table | 1 pc |
B | Door | 1 pc |
C | Lid | 1 pc |
D | Weather cover | 1 pc |
E | Natural gas orifice | 1 pc |
F | Lava rock (13.2 Ibs) | 1 box |
ASSEMBLY INSTRUCTIONS
-
Carefully unpack all parts from the box, compare parts with package content listed above, make sure all parts are present before beginning assembly of product. If any part is missing or damaged, do not attempt to assemble the product. Contact customer service for replacement parts.
-
Put the lava rocks (F) around the burner, then remove the label from the pilot box (See Figure 2). A gas fire pit requires 13.2 lbs lava rocks.
WARNING: keep children away during assembly, as this item contains lava rocks, which are small pieces and can be swallowed by children.
NOTE: leave the pilot box uncovered by the lava rocks.
-
Place the gas cylinder into the cylinder holder. Secure the cylinder by tightening clockwise the butterfly screw found on the cylinder holder (See Figure 3), so that the cylinder cannot move from side to side or fall down. Connect the regulator, screw the black handle (See Figure 4) clockwise to tighten, turn the black handle counterclockwise to remove. The knob on the control panel is turned all the way to the “OFF” position when the fire pit is NOT in use.
-
Attach the door (B) with fire table (A) tenderly (See Figure 5). Place the Lid (C) onto the fire bowl when not in use to protect it from the elements or when fire pit is cool COMPLETELY after the use (See Figure 6).
-
Cover the fire pit with the outdoor Weather cover (D) when not in use to protect it from the elements or when fire pit is cool COMPLETELY after the use (See Figure 7).
NATURAL GAS CONVERSION
Natural gas conversion must be performed only by natural gas provider or service company.
-
Disconnect the propane hose from the gas valve (See Figure 8).
-
Unscrew and disconnect the propane orifice from the bellows (See Figure 9). Propane orifice (dia2.21mm size) is painted with red mark.
-
Replace the propane orifice with the natural gas orifice, screw the natural gas orifice with the bellows tightly, then connect and tighten the natural gas orifice with inlet tube (See Figure 10). Natural gas orifice (E) (dia4.18mm size) is painted with black mark.
-
Connect the natural gas hose with the gas valve by screwing clockwise tightly (See Figure 11). Plug the natural gas fixture into the natrual gas supply piping system (See Figure 12).
-
Stick and cover the conversion label onto the propane rating plate (See Figure 13).
BATTERY
Make sure the control knob is in the “OFF” position. Unscrew the push
button cap on the ignitor module located on the control panel to access the
battery compartment. The ignitor module requires one AAA size battery.
BATTERY IS NOT INCLUDED. (See Figure 14)
LEAK TEST
To prevent fire or explosion hazard when testing for a leak:
- Always perform the leak test as described below before lighting this appliance or each time the cylinder is connected for use.
- Do not smoke or allow other sources of ignition in the area while conducting a leak test.
- Conduct the leak test outdoors in a well-ventilated area.
- Do not use matches, lighters or a flame to check for leaks.
- Do not use this appliance until any and all leaks are corrected. If you are unable to stop a leak, disconnect the propane supply. Call a gas appliance service shop or your local propane gas supplier.
cylinder-regulator connection (Figure 15)
gas valve-bellows connection (Figure 16)
gas valve-hose connection (Figure 17)
inlet tube-bellows connection (Figure 18)
To perform a leak test:
- Make 2~3 oz. of leak solution by mixing one part liquid dishwashing detergent and three parts water. Noted: make sure control knob is “OFF”.
- Apply several drops of solution where the cylinder attaches to regulator (See Figure 15), inspect the solution at the connection looking for bubbles. If NO bubbles appear, the connection is secure. If bubbles appear, the connection has the leak, disconnect the regulator, reconnect, perform another leak check. If you continue to see bubbles after several attempts, cylinder valve is defective and should be returned to cylinder’s supplier.
- Apply several drops of solution where gas valve attaches to bellows (See Figure 16), where gas valve attaches to hose (See Figure 17), and where inlet tube attaches to bellows (See Figure 18). If NO bubbles appear, the connections are secure. If bubbles appear, the connection has the leak, disconnect, reconnect, perform another leak check. If you continue to see bubbles after several attempts, the part is defective and should replace the part.
LIGHTING INSTRUCTIONS
- Push in gas control knob slightly and turn to “OFF”.
- Turn gas control knob the “ON/MIN”.
- Push in gas control knob all the way and hold. Continue to press the ignition button for 15 seconds.
- If the burner does not light in 15 seconds, release the knob and it will pop back out. Wait 5 minutes before attempting to light the burner again, repeat step 1 to 3.
TO TURN OFF GAS
- Push in gas control knob slightly and turn to “OFF”.
WARNING: For your safety, read and follow the Lighting Instructions in
this manual and in the Rating Plate on the appliance. IMPROPER LIGHTING
PROCEDURES COULD RESULT IN A FIRE HAZARD OR EXPLOSION HAZARD OR PROPERTY
DAMAGE, INJURY OR LOSS OF LIFE.
Observe Flame Height When Lit: The burner will display blue and yellow
flames. These flames should be a blue / yellow color between 1~2 in. height
(See Figure 20). These flames should not be yellow or produce thick smoke.
This would indicate an obstruction of airflow through the burners. The flames
should be blue with straight yellow tops.
CARE AND MAINTENANCE
To enjoy the outstanding performance from your fire pit, make sure you perform the following activities on a regular basis:
- Use warm soapy water for cleaning. Never use flammable or corrosive cleaning agents.
- While cleaning the fire pit, make sure to keep the area around the burner dry at all times. DO NOT submerge the control valve assembly. If the gas control is submerge in water, DO NOT use it. It must be replaced.
- Air flow must be unobstructed. Keep controls, burner, and circulating air passageways clean. Signs of possible blockage include:
- Gas odor with extreme yellow tipping of flame.
- Fire pit does NOT reach the desired temperature.
- Fire pit flame is excessively uneven.
- Fire pit makes popping noises.
- Spiders and insects can nest in burner or orifice. This dangerous condition can damage fire pit and render it unsafe for use. Clean burner holes by using a heavy-duty pipe clearer. Compressed air may help clear away small particles.
- Carbon deposits may create a fire hazard. Clean burner with warm soapy water if any carbon deposits develop.
- Cover your fire pit with an outdoor weather cover when not in use to protect it from the elements.
NOTE: Always allow fire pit to cool COMPLETELY before you cover the fire pit with an outdoor weather cover or you attempt the service or maintenance.
REPLACEMENT PARTS LIST
NO | PART# | DESCRIPTION |
---|---|---|
1 | PD-F180060-A | Fire table assembly |
2 | PD-F180060-B | Door |
3 | PD-F180060-C | Lid |
4 | PD-F180060-D | Weather cover |
5 | PD-F180060-E | Natural gas orifice |
6 | PD-F180060-F | Lava rocks |
7 | PD-F180060-G | Thermonuclear |
8 | PD-F180060-H | Hose assembly |
8 | PD-F180060-I | Foot glider |
WARRANTY
Firepits
Burner, steel fire pit bowl, all mechanical parts and fittings to control
panel and burner assembly, and all fire pit tops that are not cast aluminum
are warranted for a period of one (1) year from original date of purchase,
against defects in material and or workmanship. Rust is not covered.
Frames
Frames are warranted to be free from defects in materials and workmanship for
a period of one (1) year.
Damage to frames or welds due to improper assembly or exposure to water and
sub-freezing temperatures, is not covered. Breakage that is a result of
product being dropped, acts of God, acts of war, etc. are not covered.
Finish
The finish is warranted against peeling, cracking, or blistering for a period
of one (1) year provided the product has not been scratched or abraded.
Scratches and chips resulting from normal wear and tear are not covered.
Fading resulting from exposure to elements is not covered. Stains as a result
of chemical spills and certain food items are not covered.
Table Tops
All table tops are warranted for a period of one (1) year from original date
of purchase, against defects in material and or workmanship. Breakage,
discoloration, staining, and or any other weather related issues are not
covered.
Warranty Exclusions
Failure caused by unreasonable or abusive use. Firepits that were clearance
items, display models or items purchased in an “as is” condition, freight
damage, firepit damaged by acts of nature, vandalism, fire, abuse, lack of
proper care and maintenance, or improper assembly; straps and normal fading or
discoloration from exposure to elements, oils, spills, fluids or chemicals;
Table top against breakage; hardware against corrosion or rusting; buckling or
splitting of tubing resulting from exposure to water and freezing
temperatures; glass table tops, purchased or replacement parts; plastics. Also
excluded: loss of use of time and or inconvenience, money, travel, packaging
or any other consequential or incidental damages. In no event shall our side
responsibility exceed the value of the replacement product. Warranty is to the
original purchaser when items are purchased from one of our authorized
retailers and is not transferable. All warranty claims must be submitted with
a dated register receipt within the warranty period. Should replacement of the
warranted item be unavailable, our side reserves the right to substitute items
of our choice similar in style, color and quality. For quality control
purposes and verification, we reserve the right to request photographs of the
damage item(s). The terms of this warranty are subject to change without
notice.
To obtain warranty service please contact Foremost Groups Customer Relations Department email us at customerservice@ecotop- china.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>