Jinhua Wireless Hub/Probes Owner’s Manual

Jinhua Wireless Hub/Probes

Specifications

• APP System: Android 4.3 & iOS 8.0+
• Chip: DA14531 BLE5.1 Disable
• Bluetooth: In the Hub 5V
• OTA: 5mAh Chargeable 30min
• Dimensions: Not specified
• Charge type: Not specified
• Charge Voltage: 5V
• Battery: 5mAh Chargeable
• Charge time: 30 minutes
• Duration under running state: 30 hours
• Sensor: NTC resistance
• Temp Range for Food: -4~220°C
• Temp Range for Grill: -4~600°C
• Temp accuracy: -4~140°C
• Storage temp: Not specified
• Waterproof level: IPX7
• Default emit power: 2.5db
• Open field effective distance: 50m

Product Usage Instructions

Turning On/Off the Hub
To turn on the Hub, follow the manufacturer’s instructions. To turn off the Hub, press and hold the power button until the device powers down.

Turning On/Off the Probe
To turn on the Probe, place it in the Hub. After 3 seconds, remove it from the Hub, and the Probe will be turned on automatically. To turn off the Probe, ensure Bluetooth is not connected. If the ambient temperature stays lower than 122°F for 30 minutes, the Probe will shut off.

• The Probe will not shut down when Bluetooth is connecting with the Hub. If there is no operation for 30 minutes, the Probe will shut off. While the Probe is in a charging state in the Hub, it will immediately turn off the broadcast, disconnect Bluetooth, and shut off.

Turning On/Off the Hub

• Put the Hub on the place where is no more than 10 meters away from the Grill, and plug it into a standard power outlet.
• Push the Power button on the Hub to turn on it.
• Push the WIFI button, the Hub connects the cell phone via WIFI
• The Hub receives data of probe temp and battery energy via Bluetooth, meanwhile sends these data to a Cell phone via WIFI.
• Place the probes in the Hub, the probes will be recharged with red LED light blinking.
• Push the Power button again to turn off the Hub.

Turning On/Off the Probe

1. The probe is placed in the Hub after 3 seconds, then take it out of the Hub, the probe will is turned on automatically.
2. After the probe is turned on, when Bluetooth is not connected, the probe begins to measure temperature and broadcast. If the ambient temperature measured stays lower than 122℉for 30 minutes, the probe will be shut off.
3. The probe will never shut down when Bluetooth is Connected to the Hub.
4. No Operating for 30 minutes The Probe will shut off.
5. As long as the probe is in the charging state in the Hub, the probe will immediately turn off the broadcast, disconnect the Bluetooth, and shut off

Specifications

10

|

Duration under running state

| ≥30h|
11| Sensor| NTC resistance|
12| Temp Range for Food| -4~220℉|
13| Temp Range for Grill| -4~600℉|

14

|

Temp accuracy

|

±2℉

|
15| Storage temp| -4~140℉|
16| Water proof level| IPX7|
17| Default emit power| 2.5db|

18

| Open field effective distance|

50m

|

10~15m (Lid closed)

FCC Statement

Federal Communications Commission (FCC) Statement.
This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Warning: Changes or modifications made to this device are not expressly approved by Jinhua Xin’an Electric Co., Ltd. may void the FCC authorization to operate this device.Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

RF exposure statement:
This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The device is installed and operated without restriction.

Frequently Asked Questions

• Q: How do I charge the probe?
  • A: The probe charges in the Hub. Simply place it in the charging slot to begin charging.
• Q: What is the waterproof level of the probe?
  • A: The probe has an IPX7 waterproof level, making it suitable for use in wet conditions.
• Q: How long does the battery last in a running state?
  • A: The battery of the probe lasts for approximately 30 hours in a running state.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>