blinds2go smartview-cassette-23 Electric Roller Blinds Installation Guide

blinds2go smartview-cassette-23 Electric Roller Blinds

Specifications:

• Installation methods: Top-Fixing, Face-Fixing, Side-Fixing
• For Cassette finish: Face-Fixing
• Minimum distance of outermost brackets for cassette finish: 5cm from ends of the rail

Product Usage Instructions

Fitting the Brackets:

Standard Finish Brackets:

• Top-Fixing: Use the screw holes in the bracket to fix it directly to the lintel.
• Face-Fixing: Attach the bracket to the L-plate using small screws provided, then fix it to a facing wall or window frame.
• Side-Fixing: Recommended only if the width measurement was taken at the top of the recess.

Cassette Finish Brackets:

• For face-fixing, follow the same steps as for standard face-fixing installation.
• Ensure that the outermost brackets are at least 5cm away from the ends of the rail.

Fitting the Blind:

Standard Finish Blind:
Locate the pin-end of the blind into the central hole in the corresponding bracket. Lift the control end and slot the lugs into the slots on the bracket.

Cassette Finish Blind:
Hold the cassette at an angle and locate the central lip along the top onto the front hook of the bracket. Raise the back of the cassette and push up firmly into the brackets until they snap into place.

For SmartView Roller Blinds:
To charge the motor, plug in the charging cable included into the motor charging port until the LED on the charger plug turns green. Install the SmartView app by scanning the QR code on the swing tag that comes with your blind.

Additional Information:
If adjustments are needed such as changing control location,direction of roll, or trimming, controls can be unplugged from the tube prior to fixing brackets.

FAQ:

Q: How can I recycle my electrical and electronic devices?
A: You can recycle your devices for free at your local recycling center. Visit Recycle More website and enter your postcode to find the nearest center. Blinds 2go Ltd is part of the DTS scheme.

Fitting the brackets

Standard finish

The brackets offer three methods of installation:

Top Tip

Top-fixing or face-fixing are recommended for most installations, whereas side-fixing is only recommended if the width you gave us was taken right at the top of the recess.

Cassette finish

The brackets offer two methods of installation:

For top-fixing, simply use the two screw holes in the bracket to fix it directly to the lintel. For face-fixing, attach the bracket to the L-plate using the small screws provided. Then, use the holes in the back of the L-plate to fix it to a facing wall or window frame.

For cassette finish, note that the position of the outermost brackets should be at least 5cm away from the ends of the rail,with any other brackets evenly distributed across the width.

Fitting the blind

Standard finish

Locate the pin-end (the opposite end to the controls) of the blind into the central hole in the corresponding bracket. Lift the control end of the blind and slot the rectangular ‘lugs’ into the corresponding slots on the bracket.

Cassette finish

To fit the cassette into the bracket, hold the cassette at an angle and locate the central ‘lip’ along the top of the cassette, onto the front ‘hook of the bracket.

Now raise the back of the cassette up and push up firmly into the brackets until you hear them ‘snap’ into place.

For SmartView Roller Blinds

Once your blind is installed we recommend plugging in the motor to allow it to fully charge before use. Plug the charging cable (included) into the motor charging port and allow to charge until the LED on the charger plug turns green.

On the front of the swing tag that comes with your blind, you’ll find a handy QR code you can scan with your phone. Scan this to download the SmartView app – you’ll be setting up your blinds in moments!

Additional Information

Control location (not applicable for cassette finish)

We will have positioned the controls where you requested during the ordering process. However if you decide to swap the side that they are on, direction of the roll or need to trim the blind further, the controls can be removed by simply unplugging them from the tube. This should be done prior to fixing the brackets.

Recycle your electrical and electronic devices free at your local recycling centre. To find your nearest centre, visit the Recycle More website and type in your postcode.

Blinds 2go Ltd is part of the DTS scheme.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>