Eyoyo-ZB0859MG Pipe and Wall Video Inspection Systems Instruction Manual

Eyoyo-ZB0859MG Pipe and Wall Video Inspection Systems Instruction Manual

Read instructions carefully before operating this system

WARNING

1. Never use this device in an environment with explosive materials such as GAS, OIL, ETC.
2. Avoid using the device in extremely cold, hot or humid environment; otherwise it may damage the device. Do not drop or press hard on the device.
3. Avoid using the parts / components from other manufacturers to this system, which may damage the equipment due to the un-compatibility.
4. Warranty invalidation if the device is disassembled by users or if there are any physical damages.
5. Always back up your data before connecting your USB stick / Micro SD Card to this system. The manufacturer is not responsible for any data damage or loss on your USB stick / Micro SD Card for any reason.
6. Do not disconnect the unit while recording or playing. It may damage the unit and/or the USB stick / Micro SD Card.
7. Don’t misuse the Battery Charger Cable and Power Cord, otherwise the battery pack may be damaged or the system can not work properly.
8. The system’s PUSH CABLE made of fiberglass is very rigid and not flexible. It CAN NOT be bent sharply or pushed too hard; otherwise it will be broken.
9. If you have an extra portable cable reel, and try to put it in the case after use, you must put it in the right position; otherwise, LCD monitor may be broken by the part on the reel when you close the case.
10. Pleases forgive that if any change of products will not make additional specify in advance.

Assembly Drawing and Parts List

CAMERA
5| 0.5M VIDEO CABLE(6PIN-8PIN)
6| 0.5M VIDEO CABLE(6PIN-6PIN)
7| REMOTE CONTROL
8| Sponge column cleaning(option)
9| Scrape mud silicone sheet(option)**

Specifications

13.5V DC 1700mA

Battery（In the case）| LI-ION battery，DC 12V，4400mAh
Length of Cable| 40M
Camera Light Source| 12PCS LED
Camera Angle-of-View| FOV=90° /120°      F2.8/2.42mm
Camera Image| Effective Pixel Array: 976 (H) x 496(V)
Monitor Screen Size| 7” TFT LCD Color Monitor
Monitor Picture Resolution| 800*480 pixel (for 7” LCD)
Storeage Device| USB &TF(8G~64G)
DVR Format| AVI
System Operating Temperature| -20°C to 60°C

Application

1. WATER SUPPLY
2. WASTE WATER
3. ELECTRICAL AIR CONDITIONER
4. CABLE DUCTING
5. DUCTED VACCUM SYSTEMS
6. PLUMBING
7. BUILDINGS

WARNING:
NEVER USE THIS DEVICE IN AN ENVIRONMENT WITH EXPLOSIVE MATERIALS SUCH AS GAS, OIL, ETC

Know Your Device

Control Box

1. RESET：Reset the meter counter.

2. M/FT: Switch Meter or Feet.

3. SYSTEM：DVR system power LED indicator.

4. BATTERY：Battery indicator.
   Discharge instructions state：When the unit is turned ON, the battery level will be reflected by the green LEDs. When the LEDs flash from green to red light, the battery is insufficient and needs to be recharged.

5. MIC on/off：MIC switch. When recording using the microphone during video recording，press the green button switch. The indicator LED will light up. After the end of the video，you must press the switch again，otherwise there is no audio signal output and the audio will not be recorded onto the video.

6. (5)(7)、USB& TF pin, When use U disk &TF card as a storage device， please insert into the right port.

7. REC：Record video button.

8. UP：DVR user menu up operation button.

9. PLAY/ENT：DVR play or select button.

10. Nonfunctional button

11. DVR on/off ：DVR user menu on/off button.

12. DOWN：DVR user menu down operation button.

13. STOP/EXIT：Exit DVR video playing or return to the next higher level submenu.

14. SETUP：DVR system setup.

15. MIC power LED indicator.

16. MIC: Microphone.

17. IR：It blinks when the remote control is in use for Recording Video.

18. ERR：It indicates that the system or USB device has error.

19. USB：It indicates that USB stick/Micro SD is connected.

20. REC：It will blink during recording.

21. DVR：It indicates that the DVR system is on.

22. REM：Remote receiving window.

23. POWER：It indicates that the DVR system is on.

24. CAM2：common camera socket 2(4 core interface).

25. SIGANL：Signal interface(8 core interface).

26. CAM1：Common camera socket 1(6 core interface).

27. DC13.5V IN：Adapter DC13.5V in.

Display Part

1. VIDEO
2. MENU
3. DOWN
4. UP
5. SEL
6. LED ON/OFF
7. REM
8. power LED indicator
9. POWER
10. Signal interface（8 core interface）
11. 7 inch LCD
12. sun shade

Remark:

1. MENU key-press： Image adjust. Press SEL/DOWN/UP key to adjust below numerical value. Numerical value is from 0 to 100.
   Language has
   ENGLISH,DEUTSCH,FRANC,ESPAKOL,PORTUG,ITALIANO,EN LES, PNCCK
   BRIGHT——————————50
   CONTRAST————————-50
   COLOR——————————-50
   SHARP——————————-50
   LED BRIGHT————————80
   HUE———————————–50
   After exit “MENU” mode, below keys have different functions:

2. DOWN: Press DOWN key, the image change UP and DOWN (Mirror function)

3. UP: Press UP key, the image change LEFT and RIGHT (Mirror function)

4. SEL key: Press SEL key to change the image to 16:9 image or 4:3 image (except 10 inch monitor )

Cable Reel Base:

1. Ф5.2mm fiberglass cable
2. handle
3. camera head holder
4. Muddy water cleaner
5. locker
6. Equipment base
7. Rubber plug

1. when placing the push rod cable into the cleaner, both grooves must be aligned in the same direction(as picture 1)
2. After set the push rod cable well, then turn the both catches to two different directions before using(as picture 2)

warning:

1. When inserting the push rod cable in or out of the cleaner, both grooves must be adjusted to same direction.
2. When rolling the cable back into the cable reel, please be careful not to forcefully over-bend the cable to avoid breaking the cable.

C23B Series Camera Head

Working environment

1. Temperature: -20℃~60℃
2. Humidity：90%RH (non-condensation)

Main Technical Indicators

1. Power source input: DC 9-13.5V
2. Camera module:
3. Image sensor: 1/3″ color CMOS PC1099
4. Effective Pixel Array: 976 (H) x 496(V)
5. Horizontal resolution: 900TV LINES
6. Minimum illumination: 0.01LUX/F1.2
7. SNR: >45dB (AOC on)
8. Video Output: 1.0 Vp-p / 75Ω(CVBS)
9. Input voltage: DC 9-13.5V
10. Current consumption: 65mA Max(ALL LEDS LIGHTS ON≤200mA)
11. Lighting source:
12. LED quantity: 12pcs
13. Luminous flux: 107~114 lm（180 mA） Working Current: 0~180 mA
14. Light Cup Angle: 45°

External Interface

Camera interface: Pin 1 to 4 are separately connected to VIDEO, GND, +12V, LED.
Panel Signal Interface: Pin 1 to 8 are separately connected to CAM-VIDEO-IN, LED, +12V-IN, DVR-5V-OUT, +12V-OUT, DVR-VIDEO-IN,GND， CAM-VIDEO-OUT.

CD23FT Series Camera Head

Working environment

1. Temperature: -20℃~60℃
2. Humidity：90%RH (non-condensation)

Main Technical Indicators

1. Power source input: DC 9-13.5V
2. Camera module:
3. Image sensor: 1/3″ color CMOS PC1099
4. Effective Pixel Array: 976 (H) x 496(V)
5. Horizontal resolution: 900TV LINES
6. Minimum illumination: 0.01LUX/F1.2
7. SNR: >45dB (AOC on)
8. Video Output: 1.0 Vp-p / 75Ω(CVBS)
9. Input voltage: DC 9-13.5V
10. Current consumption: 65mA Max(ALL LEDS LIGHTS ON≤200mA)
11. Lighting source:
12. LED quantity: 9 pcs
13. Luminous flux: 107~114 lm（180 mA） Working Current: 0~180 mA
14. Light Cup Angle: 45°

External Interface

Camera interface: Pin 1 to 4 are separately connected to VIDEO, GND, +12V, LED.
Panel Signal Interface: Pin 1 to 8 are separately connected to CAM-VIDEO-IN, LED, +12V-IN, DVR-5V-OUT, +12V-OUT, DVR-VIDEO-IN,GND， CAM-VIDEO-OUT.

Remote Control

(For Operating DVR and SD Card Recording)

1. Enter：Enter to view and play video
2. Up: Go to up/previous item
3. REC: Start recording/ Snap Shooting (only available for new version)
4. SETUP: System setup and recording features
5. POWER: System in
6. Down: Select down/next item
7. STOP: Stop or escape from current menu
8. Left: Select Left item
9. Right: Select Right item
10. Rewind: Review video
11. Forward: forward video

System Set-Up

1. IMPORTANT: When you connect the Camera to the Monitor, the power must be off; otherwise both units will be damaged.

2. Connect the reel cable to the Monitor.

3. Plug the Power Adapter cord into the wall AC socket and the other end into the”DC 13.5V”jack.
   Note : Do not misuse the Power Cord and Battery Charger Cable, otherwise the system can not work properly, or the battery pack may be damaged.

4. Press the POWER button on the front of the Monitor.

5. Gently lower the Camera into a pipe duct, etc and reel out the Cable until it is at the desired depth.

6. Record the pictures if you need (see DVR Operating).

7. Video Out: By using a video cable you can transfer the picture to another larger Screen.

8. When you finish the job, carefully remove the Camera head from the pipe duct, etc, clean it with a clean, soft and dry cloth and then put the Camera into the previous position.

System Menu Setting

Clock setting: set date and time

*Time Format| Select: 24Hour – 12Hour
Year| Set year
Month| Set month
Day| Set day
Hour| Set hour
Minute| Set minutes
Second| Set seconds
Language Setting| Select: English – Chinese
System: showing software version, product version, free space and used space (when

USB/ Micro SD Card is connected)

Record setup: Storage Device Selection —USB Device or Micro SD card

Play Mode: No circle, One circle, List circle
Master reset: press OK again to perform a master reset
Firmware update: locate the directory where new firmware is stored
Browse File:Showing all files on the current USB/ Micro SD Card medium.
Remove USB/Micro SD Card device (only when USB/Micro SD Card device is connected)
Always use this option before safely removing the USB /Micro SD Card device from the USB/Micro SD Card port

Remark: When you plug in the USB key/Micro SD card before starting the device, maybe the device can’t find the USB stick/Micro SD card. In this case, please remove them and try again.

DVR/Micro SD RECORDING OPERATION

(Recording via MICRO SD Card is only available for the new versions)

1. Set the Screen Video Button on Video 2.

2. Take off the isolation sheet from the Remote Control Battery.

3. Press the Remote Control Button 5 to enter the Recording system, you can see DVR system Recorder PLAY VIDEO manual on the screen.

4. Insert your USB stick/ removable hard disc etc into the USB Port, or Micro SD Card into Micro SD Card Slot, you can see USB stick/ Micro SD Card Connected on the screen and the LED light indicator is on.

5.  Press Remote Control Button 3 to start the recording and the
   RECORDING LED light is on. In the recording, if you press the RECORDING button again, the DVR will take a photo and it is saved in the USB key or Micro SD card (only available for new versions).

6.  Press Remote Control Button7[stop]to stop recording.

7. Press Remote Control Button 1 to review recording.

8. If you need to manage your recorded pictures, press Remote Control Button 4[SETUP]You can also manage the files by selecting the SETTING on PLAY VIDEO manual on the screen.
   NOTE:
   DVR system sometimes need 10 – 20 seconds for reposition before it can work properly, please let it run about 20 seconds each time when you try to record.
   USB flash disk and Micro SD card max memory is 8G bit.
   The recorded video files will be found in a directory of USB/Micro
   SD devices.
   You can use the on-screen menu or press (REC) button to start recording. Press ( /EXIT) button to stop recording. During the recording, the screen will display recording time and time limit (up to 60 minutes).

Recording time limit

Sometimes you may forget to stop the recording after it is initiated.
This unit is featured with a recording time limit. The default time limit is 60 minutes. If recording time over 1 hour, the system will record with a new file.
Schedule recording
You can schedule a recording in advance. Simply enable the schedule recording in the SETUP and then the unit will ask user to setup timing. Recording schedule can be used once.
You have to set up schedule again for next recording.

Recording via USB Stick / Micro SD Card

The unit can be used to record video and voice via USB devices / Micro SD Card .The recorded video will be stored in the USB devices / Micro SD Card and played back on the TV screen.

Video recording format

The default video recording resolution is 640480. One-hour recording will take up storage of 500MB. User may select 320240 to save storage space.

Voice recording

A microphone button located on the front panel allows the user to press the button on to record a voice while the video is recording (This function is only available for new versions).

Video Playing

You can use on-screen menu to enter “play video” mode. The unit will display the recorded video and other compatible videos stored in USB stick / Micro SD Card. It will not list the non-compatible videos.

Select the Video File.

When you enter “play video” mode, the set will display all of the available video files on the screen.
You can use [▲] or [▼] button to select desired video and press [►/ENT] button to play.
Press and hold [▲] or [▼] button to go to previous or next video.
Use [►/ENT] button to start or pause the playing .Use [■/exit] button to stop or go back to previous menu.
The screen will display “loading, please wait …” for a few seconds before playing video.

Fast Forwarding and Rewinding

You can use [►] or [◄] button on the remote control to fast forwarding or rewinding (1x, 2x, 4x, or 8x, speed). Always press [►/ENT] button to go back to normal playing.

Compatible video format:

Divx3.11/Divx4/Divx5/MPEG1/MPEG2/MPEG4 (MPEG4 video file format: .avi, .m4v, .MPG, MPEG, .VOB)

Note: The video player of the device may not support some downloaded videos.

Video Player Software Installation

Generally, the recorded videos can be played on the computer purchased after the year 2006. If you can not open the recorded document on computer,there are two options:

Option 1：Go to the website“ http://www.kmplayer.com/ ”and download the KMPlayer software for free.
Option 2: Install the Media Player Software with the Disc
Steps：

1. Create a new folder on the computer
2. Put the disc in the computer drive, open the files in the disc and copy all the files to the above new folder on the computer.
3. Click fullplaye.exe in the new folder.

Open the media player

Click the icon “Open File” and choose the videos in AVI format to open.

Recharging the Battery

1. Plug the charger into the AC socket on the wall and insert the other end into the DC jack (See Figure2- A).
2. The battery can be charged while the device is being used. However, once the power in the battery runs completely out, it can only be charged when the device is turned off.

IMPORTANT MESSAGE: Do not overcharge the battery! Overcharging can result in acid leaking from or damage to the battery.

Battery specifications:

1. TOTAL POWER ≦15W
2. LI-ION BATTERY 12VDC MAX. ≦ 52.8Wh
3. CHARGER 13.5V 1700mA
4. CHARGE TIME 4 HOURS
5. WORKING TIME ≥120 MINUTES
6. PROTECTIVE VOLTAGE 8.25V
7. THE VOLTAGE BEFOR DISCHARGING 12.6V
8. LOAD CURRENT 1200mA (INPUT 12.2V)

TROUBLE SHOOTING

2. Recharge the battery
3. Check power line and connect it again.
No signal| 1. Read the manual again and reconnect it.
2. Check the camera and screw down
3. Clean the camera pins
4. Check the pins and find if they are in the same level
The camera has weak or no light| Press the “MENU” button, locate the LED brightness setting and then adjust the brightness.
No recording| 1. Press the “Video” button and change to Video2
2. Press POWER button and the monitor indicator light is green.
3. Use another USB stick /micro SD and try
Recording abnormity| Shut off the unit and restart the unit in correct steps
Flashing pictures| 1. Deficiency of the battery power. Please recharge the battery
2.Misuse of the charger cable and power cord: switch the cables
No working of battery recharging| Misuse of the charger cable and power cord : switch the cables

References

• kmplayer.com/

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>