CONNECTIZE G6 AC2100 Dual Band Gigabit WiFi Router Installation Guide

: June 6, 2024
: CONNECTIZE

Table of Contents

Install Your Router
Set up Your Router
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Installation Guide
AC2100 Dual-Band Gigabit WiFi Router
Model: G6

Install Your Router

Turn off your modem, cable the modem to the router’s WAN port.
Turn on the modem and wait 2 minutes for it to restart.
Connect the power adapter to the router and press the Power Button.
Flip to the next page to continue with the setup.

If your Internet comes (roman Ethernet outlet. please connect the router’s WAN port to It. and then follow Steps and Pat 2: Set up your Pouter.
If you want to configure this router as an access point(similar to a ME i extender) to extend the existing network. please refer to the Access Point Mode section on the next page.

Turn off the modem, cable the modem to the WAN port on the router.
Turn on the modem and wait 2 minutes for it to restart.
Connect the power adapter to the router, and press the Power Button.

If your Internet comes from an Ethernet outlet, please connect the router’s WAN port to it. and then follow Step 3 and Part 2: Set up Your Router.
If you want to configure this router as an Access Point(similar to a WiFi extender) to extend the existing network, please refer to the Access Point Mode section on the first page. $

Set up Your Router

1. Connect your device to the router (Wireless or Wired)

Wireless
Wired
For a wired connection, use an Ethernet cable to connect your computer to a LAN port on your router.

https://register.iconnectize.com/setup

2. Connect the router to the Internet.

L og in to the router (The default login password Is admin.)
Launch a web browser, enter http://connectlzewlfi.com or 192.168.5.1, and a login page displays.
PS: If the login page does not display, please refer to 03 of FAO.
Choose the connection type.
The webpage detects your connection type automatically. If detection fails, choose your connection type manually, then click the Next button.
PS: If you click the Skip Wizard button, the router will follow the auto- detected connection type, meanwhile the login password, SSID. and WiFi password will be set as default.
Set the WWI Name, WiFi Password, and Login Password.
It’s advised to set a stronger password to ensure a secure family network. Then follow the step-by-step instructions of the Quick Setup Wizard to connect to the Internet.

LED	Status	Description
PWR	Solid on	The power is on.
2.4015G	Solid on	The 2.4Glizi5Gliz network is enabled.
Blinking	Transmitting data.
WPS	Solid on	The VVPS negotiations are completed.
Blinking	Awaiting the WPS connection.
USB	Solid on	The USS device is connected.
WAN	Solid on	Connected to the Internet.
Blinking	Transmitting data.
LAN	Solid on	Device connected.
Blinking	Transmitting data.

DC	Power Port: Connect the included AC power adapter.
PWR	Power Button.

LAN Ports
( 1, 2, 3, 4 )| Connect Ethernet cables to these ports, and to wired devices on your network.
WAN Port| Connect an Ethernet cable to this port, and to a broadband Internet cable/DSL or fiber modem.
USB| Connect and share USB drives on your network.
WPS| Press it to connect to the WPS-enab led network devices.
RST| Reset Button, hold the button for 10 seconds to factory reset your router.

Ways to Reset the Router

With the router powered on. hold the RST button on the back until the Power LEO starts blinking.
Log in to the web management page. go to Advance >Selected Menu >Conf lg. and click Reset.

AP (Access Point) Mode
In this mode, the Connect router can work as a WiFi extender to turn a wired network into a wireless network. extending the WiFi range.

Connect the existing router to the Connect Router.
Cable Connect router’s WAN or LAN port to your existing router’s Ethernet port. as shown above.
Connect a computer to the Connect router. Use an Ethernet cable, or wirelessly by joining the default SSID printed on the label.
Log into the Connect router. Visa http://connectizewifi.com in a browser. Complete the instructions if this is the first time you’re setting up the router.
Enable AP Mode. Go to Internet Settings. select Bridge(AP) in Connection Type, and click Save& Apply. Wait for the router to reboot. It will complete the AP Mode setup automatically.

USB Sharing

Please insert the USB device (NTFS advised) to the router first, configure your account and folder permissions on the USB-related pages.

Windows
Users of Windows 7 and below do not need to set it separately: For Windows 10 users. enable the SMB 1.0 in Control Panel >Programs Programs and Features:
macOS
Enter the SMB address in the Safari browser to access:
After you finished tne settings abOve. enter the corresponding SMB address in the file manager or browser (Only for macOS) of your device, and fill in your Account info to enjoy it.

FAQ
For more questions and answers. please visit www.iconnectize.com/faq
01: What connection type to choose if the router failed to detect automatically?

Type	Description
PPPoE	Applicable to use if your ISP provided a PPPoE username and password.
DHGP	Obtain IP address from ISP automatically.

If your ISP does not provide a username and password. choose DHCP to connect.
Static P| Ask configurations from your ISP if you are using a static IP.

02: Why cannot I access the Internet after installing the router?

Try connecting a computer directly to the modem via an Ethernet cable. then check if you have Internet access. If not contact your ISP.
Check if the router’s WAN port is connected to the modem properly. and confirm the indicator’s status.
If your wired devices cannot access the Internet:

Confirm if your PC is connected to a LAN port properly.
Make sure your PC is set to obtain an IP address and DNS server address automatically.

If your WiFi-enabled devices cannot access the Internet:

Reboot the router and reconnect to the WiFi. If it doesn’t work factory reset the router and repeat the router setup process.

03: Why cannot I access the web management page?
If the computer is set to a static IP address, change it to obtain an IP address automatically.

Disable the proxy server. if enabled. Also. disable the VPN software.
Disable and re-enable the network adapter being used on your computer.
Ensure that http://connectizewifl.com or 192.168.5.1 is correctly entered in the web browser.
Use another web browser and try again.
Reboot your router and try again.

04: Why my download speed cannot reach the advertised speed rate?

Devices under 2.4G WiFi will get a lower speed than 50 WiFi. Also, the wired connection will deliver a higher speed than a wireless connection.
Check if there are multiple users sharing the connection at the same time. Try to limit their speed, or if required, even block them in the web management page.
Check the Internet speed and link quality from your ISP. If the Internet is 100Mbps. you can get up to 12.5MBps download speed. (1 Byte=8 bits) Actual speeds may vary due to transmission loss.
Place the router in a central location instead of the corner to improve wireless performance. All antennas should be upright.
ry to connect the gigabit port of the modem to the router using a cat5e Ethernet cable, or better.

FCC Statement
This equipment has been tested and found to comply with the limits for a Class Bdigita1 device pursuant to part 1501 the FCC Rues These limits are designed to provide reasonable protection against harmful interference n a residential installation. This equipment generates. uses and Can radiate radio frequency energy ana if net installed and used in accordance with the instivCbOnS. may CauSe harmful interference to radio communications. However. there is no guarantee that interference will instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur ins panic-War installation. If this equipment does cause harmful interference to radio or television reception. which can be determined by turning the equipment off and on. trie user is encouraged to try to correct the interference by one or more or the following measures;
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
-connect the equipment into an outlet On a CirCuit different from that to which the receiver is connected.
—Consult the dealer a an experienced radio/TV technician for help.
FCC Radiation Exposure statement
This device complies with FCC radiation exposure Imports set forth fa an uncontrolled environment and it also complies with Part 15 of the FCC RF Rides. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna Or transmitter. End-users and installers must be provided with antenna installation instructions and consider removing the no-odic: Gamer statement. This demos °copies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received. encoding interferenCe that may Cause undesired operator).
Caution! Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Operating frequency: 2412-2462MHz. 5150-5250MHz. 5725-5850MHz

CE Mark Warning
This is a Class B product. In a domestic environment. this product may cause radio interference. in which case the user may be required to take adequate measures. Operations in the 5.15-5.25GHz band are restricted to indoor use only. This equipment should be installed and operated with a minimum distance 20cm between the device and your body.
NOTE: (1) The manufacturer is not responsible fcr any radio or TV interference caused by unauthorized modifications to this equipment. (2) To avoid unnecessary radiation interference. it is recommended to use a shielded RJ45 cable. WARNING: The mains plug is used as a disconnect device, the disconnect device shall remain readily operable.
Declaration of Conformity Hereby.
SHENZHEN TEN() NETWORK TECHNOLOGIES00.. LTD. declares that the radio equipment type G6 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://www.iconnectize.com/regulations-ce/
Operating Frequency: 2.4 GHz: EU12400-2483.5MHz (CH1-CHI3) 5 GHz: EU/5150-5250MHz (CI-I36-CH48)
EIRP Power (Max.): 2.4 GHz: 19.86 dBm 5 GHz: 22.96 dBm
Software Version: V6411391)00IX
Caution: (G6)
Adapter Model: ES0880-X120150XYF
Manufacture: SHENZHEN EAST SUN ELECTRONIC CO.. LTD.
Input:100 – 240V AC. 50160Hz. 0.6A
Output: 12V 1.5A DC Voltage
RECYCLING
This product bears the selective sorting symbol for waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys new electrical or electronic equipment.
Operating Temperature: 0°C – 40°C
Operating Humidity: (10% – 90%) RH. non-condensing