Hunter 19829 3 Light Lantern Instruction Manual

Hunter 19829 3 Light Lantern

WARNING
To avoid possible electrical shock, before installing your light fixture, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location.

READ AND SAVE THESE INSTRUCTIONS
These instructions are provided for your safety. It is very important that they are read carefully and completely before beginning the installation of the lighting fixture.

Specification

• 3 Light Lantern
• Fixture weight +2 lbs:
  • 13.5 lbs (6.12 kg)

Hardware Service Kit

Glass

• Part
  • KE30601147
• Model
  • 19829
  • 19830
  • 19831
• Type
  • Clear Glass

Here are the tools you’ll need to complete your installation:

Ladder

Screwdriver

Pliers

Wire Strippers

PREPARING FOR INSTALLATION

Carefully remove all contents from the carton. Shut off the power at the circuit breaker and completely remove the old fixture from the ceiling, including the old mounting bracket. Remove the new mounting bracket assembly from the bag. Remove cap nuts (H) from mounting screws (B). Place the mounting plate (A) over the junction box so that mounting screws (B) and nuts (C) extend out away from the ceiling.

Depending on the placement of your junction box the position of mounting screws (B) may need to be adjusted to allow the canopy to be flush with the ceiling. Adjust the position of mounting screws (B) so that mounting screws (B) can be exposed 5-6 mm after passing through the canopy (F) to properly fit the cap nuts. Mounting screws (B) can be adjusted by loosening nuts (C) and loosening or tightening mounting screws (B). Once the ideal position of mounting screws (B) has been confirmed, tighten nuts (C) on mounting sCrews (B) on the front of the mounting plate to ensure that mounting screws (B) are secure. Pull the house wires through the center of the mounting plate (A). Secure the mounting plate (A) to the junction box by tightening the screws (D).

ASSEMBLING THE FIXTURE

There are 4 12-inch rods (K), and 1 6-inch rod (0) included for each fixture. Determine the correct number of rods needed for proper hanging height. To lengthen the fixture, add additional rods. To shorten the fixture, trim the wires to the desired length. Leave at least 8 to 10 inches of wire in addition to the desired length and slide any excess rods off the fixture’s wiring to discard. Keep in mind that you must use at least one rod to hang the fixture.

Thread the wires through the center rod (M) and attach to the threaded post (N). Thread the wires through the threaded post of the strap (L) and attach them to the top of the center rod (M). Thread the wires through the rods and pull the wires until taut before connecting the rods together. All threads should be engaged but do not overtighten (some manual straightening of the downloads may be required). Pull the fixture wires through the top of the canopy (F). Screw the top rod to hang straight (G) of the canopy (F).

CONNECTING THE WIRES

Have a helper support the fixture’s weight while completing the wiring. Attach the fixture’s wires to the power supply wires from the junction box. Connect black to black (live); white to white (neutral); grounding to grounding (green or copper). Twist the ends of the wire pairs together. Then, twist on a wire connector. Make sure all twists are in the same direction. Lo0op fixture’s ground wire around grounding Screw (E) and tighten. If there is no ground wire (green or copper) from the junction box, contact a qualified electrician.

FINISHING THE INSTALLATION

Raise canopy (F) to mounting plate (A) and position mounting screws (B) so that they protrude through the openings of the canopy (F). Secure canopy (F) in place with cap nuts (H). Install a light bulb (not included) in accordance with the fixture’s specifications. Do not exceed the recommended wattage. Slide glass shade (0) into the ring (P). Raise the glass so that the fixture strap (L) sits outside of the glass shade (0) and ring (P). Secure the glass shade (0) to the fixture with the screws (0). Do not tighten screws (0) until both are in place and threads have started to be engaged. Do not overtighten sCrews (Q) to avoid GLASS BREAKAGE. Turn on the power and test the fixture. Your installation is now complete.

CLEANING TIPS

Treat the fixture gently!
Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the fixture with a clean lint-free cotton or microfiber cloth. Never spray the cleaner directly onto the fixture.

WARNING

FRAGILE GLASS
To prevent chipping/breaking of glass, do not overtighten screws.

Hunter Pro Tip:
Twist or tape wire ends together to make it easier to pass them through the downloads. Threaded posts may also be removed for easier wire access.

NOTICE
In order to use a 12in. rod by itself you must first remove the threaded post from the 6in. rod and install it on one of the ends of the 12in. rod.

02022 Hunter Fan Co. ML366.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>