SZFIXEZ SXT-160 Electric Cleaning Brush Instruction Manual

Instruction Manual
Electric Cleaning Brush
Model: SXT-160

SXT-160 Electric Cleaning Brush

Thank you for your purchase!
Please read the manual carefully before use and keep it properly for future reference.
The manual contains information about various using methods of this electric cleaning brush and some using skills, so that you can use it more easily and make your home more refreshing and comfortable.

Function introduction of switch panel

Switch button “icon”: press the “icon” button by hand, and the machine starts to enter the rotating working mode. The working indicator light is always on and displays the current power. During the operation of the machine, press the “icon” button by hand, and the machine enters the low-speed state. Then press the “icon” button of the switch, and the machine stops working, and the indicator lights are all off.

In any state, press and hold the switch button “icon” for 2 seconds to enter the locked state, and the machine stops working. In the locked state, when the switch button is pressed, the indicator light flashes, and the machine cannot be started.
When the power is too low, the lowest light on the switch panel flashes, indicating that the machine is about to shut down. Please charge it in time before using it.
During charging, the five indicator lights on the panel are on in a cycle. When the lights are on in a cycle, when several lights are not on, it indicates that the charging has been completed.
In case of improper operation, excessive load or locked rotor during use, the five lights will flash at the same time. If the wrong operation is not corrected in time, the machine will trigger overload protection after 5 seconds and auto shut down. It needs to reset its position and then restart.

Introduction to basic functions of the product

This product is mainly used for the cleaning of domestic bathroom, kitchen, living room floor, furniture, automobile and other places. The product uses high-performance lithium battery, strong power motor, two speeds, and can freely change the cleaning intensity according to different needs. The international general type-C charging cable is charged for 2 hours. The electric circuit design has the function of overcharge and overcharge, low power prompt, LED work indication, five segment power display, charging and running light flashing. The product complies with 3C, and EU safety and environmental protection certification

Product structure description

1 Sponge brush tray
2 Small mop tray
3 Fiber brush tray
4 Large bristle brush head
5 Small brush tray base
6 Anti wool brush plate| 7 Pointed brush head
8 Small hair brush
9 Wide range brush
10 Telescopic rod
11 Connector| 12 Host
13 Switch key “icon”
14 Control panel
15 Indicator light
16 Charging port sealing plug
17 Type-C charging cable
---|---|---

Warning

• Please carefully check whether the accessories are complete before use
• Do not place the charger in a humid environment
• When cleaning, be sure to check whether the charging hole is sealed
• Wipe the surface timely after cleaning to ensure that the product is dry
• This product must not be used by people (including children) who are not sound, feel or mentally handicapped or lack relevant experience and knowledge, unless they are supervised or instructed by personnel responsible for their safety.
• Children should be looked after to ensure that they do not play with these products.
• Do not use hot water when cleaning the product. When using warm water, be sure to check whether the water temperature is too high to prevent hand burns.
• Do not touch the rotating parts with hands and lapels during use
• When replacing the brush head, do not use a screwdriver or other tools to pry the brush head, just pull it out by hand
• When replacing the brush head, do not touch the switch to avoid injury caused by wrong startup
• When using, please keep away from wires, ropes and other winding parts

Introduction to charging function

1. When the power of the product is insufficient, the indicator at the bottom of the control panel will flash.
2. Open the sealing plug of the charging hole, use the special charger of this product to insert the charging head into the charging hole, and the status indicator light on the switch button flashes circularly (Fig. 2)
3. The normal charging time of this product is about 4 hours.
4. When the status indicator is fully on, it means that the power is sufficient. Unplug the charging plug, unplug the charger from the power socket, and install the sealing ring of the charging hole (Fig. 3)

Warning: when using the charger, be sure to use the original charging cable with the USB charger, and check whether the charger is wet or has water. Do not plug in the charger to use this product unless under special circumstances

Function introduction of brush head

• Wide range brush: it is perfect as a concave cleaning brush for bath, sink or toilet (Figure 3)
• Pointed brush head: it is applicable to the corners, crevices, car wheels of domestic kitchens, bathrooms or range hoods, as well as the places that are not easy to be cleaned at ordinary times (Fig. 4)
• Small flat brush head: suitable for cleaning small flat parts such as wash basin, kitchen sink and furniture (Figure 5)
•  Large flat brush head: suitable for cleaning oil and dirt in bathroom, kitchen, living room,toilet, window, glass and other places (Figure 6)
• Large and small mops: mainly used for cleaning and polishing the living room floor, glass, coffee table and car surface (Figure 7)

Note: When using brush head 1, 2, 3, 6, it is necessary to paste the brush head to the brush head base, and then use the brush head base to the machine.

• Imitatied wool brush plate can be used for polishing, waxing, dust removal, etc. of high-end household, electrical appliances, automobiles, etc. (Fig. 8)
• The fiber brush tray is mainly used for removing and polishing heavy oil stains on the surfaces of kitchens, hoods, walls, bathrooms, etc. (Fig. 9)

How to use the product

• Please charge the machine for more than 2 hours before use to ensure that the machine is fully charged.
• Select the appropriate brush head according to the use, and put the brush head on the machine.
• Press the switch button “icon” on the control panel, press the first time to rotate at high speed, and press the second time to rotate at low speed (FIG. 11)
• When the machine is working, the indicator light on the switch panel is always on. If the five lights are not on for a long time, it means that the machine is not fully charged.
• The function of the switch key is 0-1-2-0, which needs to be pressed twice when using high-level shutdown. to rotate at high speed, and press the second time to rotate at low speed (FIG. 11)

Replacement method of brush head

• When replacing the brush head, please turn off the machine first and keep your hands away from the switch button.

• Hold the brush head with your hand and pull it out vertically. It is easier to take out the brush head by gently swinging left and right while pulling it out (Fig. 12).

• When installing the brush head, align the semicircular groove of the brush head with the convex groove of the connector, and press it down vertically.
  When you hear the “click”, it is installed in place (FIG. 13).

• When using the brush tray or mop, firstly stick the brush tray on the brush tray base, and then install the brush tray base on the machine according to the installation method of the brush head (FIG. 14).

Cleaning and maintenance

1. Please check whether the charging port is sealed when cleaning
2. Do not use metal objects such as steel wires, abrasive cleaners or corrosive liquids (such as gasoline or acetone) to clean the brush head and body surface
3. You can rinse the brush head under the faucet, or turn the product to high-speed mode and automatically wash the brush head under water (do not flush the charging port with water)
4. After cleaning, please vigorously shake off the water on the product and wipe it with a cloth
5. Do not use hot water above 60 ° to clean the brush head and products

Environment protection

• When disposing of the product, please do not stack it with general domestic garbage; It shall be delivered to the recycling center designated by the manufacturer. This is conducive to environmental protection.
• The built-in rechargeable battery contains substances that may pollute the environment.
  When discarding the product, be sure to take out the battery and properly dispose of the
  battery

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>