Panasonic NN-TK73NC Microwave Oven Built In Trim Kits Instruction Manual

Panasonic NN-TK73NC Microwave Oven Built In Trim Kits

Specifications:

• Model : NN-TK73NC / NN-TK72NC
• Power Supply : 120 volts
• Outlet Requirement : 20-ampere branch circuit single grounded outlet
• Dimensions : Trim Kit Dimension – 27″ x 30″, Cutout Depth – 27 models: 1 7/8″ overlap, 30 models: 3 5/16″ overlap
• Weight Capacity : The base must support a minimum of 100 lbs (45.5 kg)

Product Usage Instructions

• Grounding Instructions:
  Ensure proper grounding to prevent electric shock. Do not use an extension cord. If power supply cord is short, have a qualified electrician install an outlet near the appliance.

• Electrical Requirements:
  Connect the product to a supply circuit of the correct voltage and frequency. Ensure wire size conforms to electrical codes. Installation should be done by a qualified electrician.

• Cutout Dimensions:
  Follow the specified cutout dimensions for proper installation. Allow clearance for air-flow to prevent damage to the microwave.

• Installation Above a Built-In Oven:
  Install the microwave on a plywood base supported by runners. The base must be capable of supporting at least 100 lbs.

• Installation Steps:

  • Locate and Install the Base Pan: Set the Base Pan into the front cabinet microwave oven cutout, center it, and mount using short screws.
  • Install the Rear Duct: Gently return the microwave oven to its upright position.

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• IMPORTANT — Save these instructions for local inspector’s use.
• IMPORTANT — Observe all governing codes and ordinances.
• Note to Installer – Be sure to leave these instructions with the Consumer.
• Note to Consumer – Keep these instructions for future reference.
• Skill level – Installation of this appliance requires basic mechanical and electrical skills.
• Completion time – 1 to 3 hours
• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not covered under the Warranty.
• This kit and microwave are approved for installation alone or above any single electric wall oven. Do not mount adjacent (within 2 feet) to any range, cooktop, gas oven, or other microwave.
• This product is to be installed 3 feet above floor level.
• Do not alter or modify any part of this kit or the oven.
• For easier installation and personal safety, we recommend that two people install this microwave oven.
• Unplug the microwave oven before attempting installation of this kit.

WARNING

• This oven must be plugged into a properly grounded 3-hole, 120 volt receptacle as required by the National Electrical Code.
• Before beginning the installation, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

PARTS INCLUDED

NOTE : This kit has extra screws to prevent the technician from spending extra time locating a replacement in case they lose one during installation.

GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded. Consult a qualified electrician or serviceman if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly grounded.

WARNING:

• Improper use of the grounding plug can result in a risk of electric shock.
• Do not use an extension cord. If the power supply cord is too short, have a qualified electrician or serviceman install an outlet near the appliance.

ELECTRICAL REQUIREMENTS
This product must be connected to a supply circuit of the proper voltage and frequency. Wire size must conform to the requirements of the National Electrical Code or the prevailing local code. The power supply cord and plug should be brought to a separate 20 ampere branch circuit single grounded outlet. The outled box should be located in the cabinet above the oven. The outlet box and supply circuit should be installed by a qualified electrician and conform to the National Electrical Code or the prevailing local code.

TOOLS YOU WILL NEED

CUTOUT DIMENSIONS

• Min. depth with receptacle outside cutout – 22”: (55.9 cm)
• Min. depth with receptacle inside cutout – 23 1/2”: (59.7 cm)

120 volt – 60 Hertz grounded power receptacle.

Bottom of trim kit must be minimum of 36” (91.4cm) from floor

WARNING
This trim kit uses air flow from the top, bottom and sides of the trim frame. Blocking the air flow can cause the microwave to function improperly and may cause damage to the microwave. Allow a 1” (2.54cm) clearance beyond the edge of the trim kit frame to provide proper air flow.

FOR INSTALLATION ABOVE A BUILT-IN OVEN:
Microwave oven should be installed on a 3/8 (1 cm)” plywood base and supported by 2×4 or 1×2 equivalent runners on all sides. Base must be capable of supporting a minimum of 100 lbs (45.5 kg).

1. LOCATE AND INSTALL THE BASE PAN
   Set Base Pan into the front cabinet microwave oven cutout and center it right and left. Push back until the front flange is against the cabinet front wall. Mount the Base Pan using 3 short screws.

2. INSTALL THE RAILS
   Disconnect the microwave oven from the receptacle. Remove everything out of the microwave oven, including packing, Owner’s Manuals, turntable and turntable support. A protective film has been applied to some microwave oven and trim kits. If applied, remove the film. Turn over the microwave oven and secure the rails to oven Base Plate by inserting 4 short screws. Be careful not to scratch the microwave oven.

3. INSTALL THE REAR DUCT

4. Gently return microwave oven to its upright position.

5. Remove Screw A, B and C, and then take off the bracket from the back of the microwave.

6. Align the rear duct with the back of microwave oven, as shown.

7. Slide 2 tabs into the slots on the right side of the back of microwave oven.

8. Use 3 short screws to secure back of rear duct to the back of microwave oven, as shown.

9. Short screws (3)

10. Rear duct

11. Back of microwave oven

12. INSTALL THE MICROWAVE OVEN
    Plug the power cord into the wall receptacle. Slide the microwave oven assembly gently into the cabinet, using care not to pinch the power cord. Be sure to keep the assembly centered as it slides back to where the tongue of the rails goes through the slots on Base Plan. The top edges of the Base Plan should now be centered right to left in the opening. The Base should be tight against the cabinet.

13. CHECK LEVELING
    Check the leveling by placing a level at the front and sides of the microwave. It may be necessary to add wood shims under the base pan to level the microwave front-to-back and side-to-side.

14. SECURE THE RAILS TO THE CABINET
    Ensure the Base Pan and Bottom Bracket front flanges are tight against the cabinet, and that the screws holes are aligned. Drive 4 short screws through the Base Pan and Rails into the cabinet

15. INSTALL THE TRIM KIT FRAME

16. Position the assembled Trim Kit frame around the oven.

17. Using Trim Kit’s 4 holes as your guide, drill pilot holes on. each corner on the cabinet using 3/32″ inch bit.

18. Secure the Trim Kit by 4 long screws through the trim kit into the cabinet by using a manual screw driver.
    IMPORTANT-
    Start all screws before tightening any one screw. Do not overtighten screws since it can cause misalignment of top/side strips.

19. REPLACE ANY LOOSE ITEMS

20. Your trim kit is now fully installed. Replace the turntable and turntable support that was removed from inside the microwave oven.

21. Keep these installation instructions and extra screws for future reference and need. Do not place them in the microwave oven.

22. Replace the house fuse, or close the circuit breaker to restore power at the service panel.

FAQ

Q: Can I use an extension cord with this product?
A: No, using an extension cord can result in electric shock. Ensure to have a qualified electrician install a proper outlet if needed.

Q: What tools are required for installation?
A: You will need 2 Phillips Screwdrivers (#1 & #2), a pencil, a Level, a Drill with 3/32 Drill Bit, and Tape Measure.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>