Ronghe YC-WH019 Magnetic Wireless Car Charger User Manual
- September 16, 2024
- Ronghe
Table of Contents
Ronghe YC-WH019 Magnetic Wireless Car Charger
Package Include
-
Input:5V = 2A, 9V = 2A
Support PD/QC Fast Charging -
Output: 5W /7.5W/10W/15W
Indicator Status
Work Normally: Light is always on
FOD (Foreign Object Detection): The light is flashing.
Product Overview
- Support Surface
- Fixed Nut
- Rotate Knob
- Supporting Plate
- Ball Joint
Installation Steps
- Unscrew the fixed nut, and place it on the ball joint of the air vent clip.
- Insert the ball joint into the socket on the back of the phone holder until you hear a “Click”
- Tighten the fixed nut.
- Rotate the knob to adjust the hook to fit the air vent blade.
- Insert the car phone mount into a suitable place on the air vent, then tighten the locking knob to secure the car phone mount firmly.
Charging Steps
- Pull out the USB-C cable to plug into the power port, then put the phone on the holder and it can be charged.
- When you do not need it, stretch the USB-C cable again, and it’ll retract itself.
Note
- About using non-standard car chargers: recommend using QC3.0 or PD18W or above.
- Metal accessories (iron pieces, finger clasps) or credit cards can interfere with charging. Phone Cases containing metal will trigger foreign object detection and interrupt charging.
- Using the phone for GPS navigation or listening to music while charging can significantly affect the charging speed. When using GPS applications, the power consumption may be higher than the charging speed.
- It is normal to have slight heating during the use of the wireless charger, if you encounter serious heating, please suspend the use and contact our after-sales mailbox.
ISED Canada Statement
This device contains license-exempt transmitter(s)/receiver (s)/ that comply
with Innovation Science and Economic Development Canada’s license-exempt
RSS(s).
Operation is subject to the following two conditions
- this device may not cause interference and
- this device must accept any interference, including interference that may cause undesired operation of the device.
Radiation Exposure
This equipment complies with Canadian radiation exposure limits set forth
for an uncontrolled environment
RF Exposure Statement
To maintain compliance with IC’s RF Exposure guidelines, This equipment
should be. Installed and operated with a minimum distance of 10mm in the
radiator of your body. This device and its antenna(s) must not be co-located
or operated in conjunction with any other antenna or transmitter.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and the receiver.
-
Connect the equipment to an outlet on a circuit different
from that to which the receiver is connected. -
Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 cm between the radiator and your body.