CONTROL by WEB X-410CW Web Enabled Programmable Controller User Guide

: September 16, 2024
: CONTROL by WEB

Table of Contents

X-410CW Web Enabled Programmable Controller
Specifications:
Product Usage Instructions:
Cloud Setup & Cell Activation:
LAN Setup Steps:
- FAQ:
Q: How do I reset the X-410CW to factory default settings?

X-410CW Web Enabled Programmable Controller

“`html

Specifications:

Power Supply: +5V
Relays: 4X
Power Input: Vin+ Power Supply Input (9-28VDC), Gnd Power
Supply Input (Ground)
Relay Configuration: Rly1-Rly4 Normally Open, Com Common For
All Relays
Digital Inputs: In1+-In4+, Gnd Ground for Inputs & 1-Wire
Sensors
Data Output: Data 5Vo +5VDC Output

Product Usage Instructions:

Cloud Setup & Cell Activation:

Register or login to your account at: www.ControlByWeb.cloud
Choose ‘Devices’ from the left navigation bar and click ‘New
Device’.
On the New Device page, select the ‘Cell Device’ tab.
Enter a device name, the last 6 digits of serial number, and
the Cell ID (located on the side of the device) and click
‘Submit’.
Click ‘Activate SIM Card’. If data plan was purchased
separately, first enter Data Plan Code (sent via email) & click
‘Apply Data Plan’. Activation may take 15 minutes. Click ‘Check SIM
Status’ to verify activation.
Once activated, power up the X-410CW. It may take up to 5
minutes to connect.

LAN Setup Steps:

Power the module and connect to the network.
Set IP address on the computer to be on the same network as the
module.
To configure the module, open a web browser and enter:
http://192.168.1.2/setup.html
Assign a permanent IP address to the module, then restart the
module.
Restore the computer’s IP address if necessary and access the
module at its new IP address to finish setup.

FAQ:

Q: How do I reset the X-410CW to factory default settings?

A: To reset to factory default settings, use the following
credentials:

IP Address: 192.168.1.2
Subnet Mask: 255.255.255.0
Control Page Web Address: http://192.168.1.2
Control Password: (no password set)
Setup Page Web Address: http://192.168.1.2/setup.html
Setup Username: admin
Setup Password: webrelay (all lower case)

“`

X-410CW | Quick-Start Guide

Cloud Setup & Cell Activation (For faster setup, we recommend doing this step first) 1. Register or login to your account at: www.ControlByWeb.cloud 2. Choose Devices’ from the left navigation bar and clickNew Device’.

3. On the New Device page, select the `Cell Device’ tab.

4. Enter a device name, the last 6 digits of serial number, and the Cell ID (located on the side of the device) and click `Submit’.

5. You’ll be redirected to the Device Edit page. *Click `Activate SIM Card’.

*Note: If data plan was purchased separately, first enter Data Plan Code (sent via email) & click Apply Data Plan’. Activation may take 15 minutes. ClickCheck SIM Status’ to verify activation.

power supply +5V
4X

6. Once activated, power

4X

up the X-410CW.

May take up to 5

minutes to connect.

Relays

Power

Vin+ Power Supply Input (9-28VDC) Gnd Power Supply Input (Ground)

Rly1 Relay 1 Normally Open

4X

Rly4 Relay 4 Normally Open

Com Common For All Relays

In1+ Digital Input 1+

4X

In4+ Digital Input 4+

Gnd Ground for Inputs & 1-Wire Sensors
Data Data 5Vo +5VDC Output

1-Wire Bus Inputs

Connect temperature or other 1-Wire sensor(s)

See users manual for setup instructions: www.ControlByWeb.com/support/ Rev 1.0

X-410CW | Quick-Start Guide
LAN Setup Steps (Recommended for Initial Setup)
1. Power the module and connect to network. 2. Set IP address on computer to be on the same network as the
module. (Example: Set computer to 192.168.1.50) 3. To configure the module, open a web browser and enter:
http://192.168.1.2/setup.html 4. Assign permanent IP address to module, then restart module. 5. Restore computer’s IP address, if necessary, and access the module
at its new IP address to finish setup.
Factory Default Settings
IP Address: 192.168.1.2 Subnet Mask: 255.255.255.0 Control Page Web Address: http://192.168.1.2 Control Password: (no password set) Setup Page Web Address: http://192.168.1.2/setup.html Setup Username: admin Setup Password: webrelay (all lower case)
1681 West 2960 South, Nibley, UT 84321, USA