FAGERHULT SE566 Touch Midi Recessed Round Installation Guide
- September 14, 2024
- FAGERHULT
Table of Contents
FAGERHULT SE566 Touch Midi Recessed Round
Specifications:
- Model: Dwide
- Input Voltage: 220-240 V
- Size Options: 600×600, 300×1200
- Installation Depth: 20 mm
Product Usage Instructions
Installation:
- Ensure the luminaire is connected before plugging it into the mains voltage.
- Avoid covering the luminaire with insulating matting.
- For ventilated or unventilated spaces, follow the specified box space requirements.
Maintenance:
Handle the product with care to avoid electrostatic discharges and mechanical
stress. Avoid direct contact with open circuit boards like LED-modules during
installation and maintenance.
Replacement:
The light source, control gear, and external cable should only be replaced by
the manufacturer or its designated person.
FAQ:
-
Q: Can I replace the light source on my own?
A: No, the light source should only be replaced by the manufacturer or their designated person. -
Q: What should I do if the product is damaged?
A: Contact the manufacturer or their designated person for repair or replacement.
The product is containing electronics which may be sensitive to electrostatic discharges (ESD) as well as mechanical stress. cTo avoid damages, any open circuit board like LED-modules should never be directly touched by hand or by a tool. This is valid both during installation and normal maintenance.
Products marked with this symbol
The light source shall only be replaced by the manufacturer or his designated
person
Products with an external driver
Some luminaires are for use with an external LED-driver. If any other
driver than standard is intended to be used it must be adapted for the
luminaire. It should be with corresponding functionality (constant current
resp. constant voltage) and electrical parameters.
Insulation test
- In order to avoid damaging the electronic ballast or other sensitive electronic devices, the phase and neutral must be connected together before any insulation test (max 500V DC).
- Automatic circuit breakers (MCB) and Residual current device (RCD)
- Due to the high peak connection current MCB:s type C is recommended.
- Peak-current-proof RCD:s adapted for electronics are recommended. Normally a luminaire has a leakage current of 1 mA.
Luminaires for dimming
- An amplifier may be required for long cable lengths or a large number of luminaires.
- Digital technology permits cable lengths up to 250 metres.
Basic insulation between mains and control wiring
- Control voltage cables may be routed with mains cables if they are mains voltage insulated. National regulations should be adopted. Control voltage cables for 1-10V are polarised (+/-) and must be connected correctly to all luminaires.
- If pulse switching via a momentary push button is used, the connected luminaires must due to functional reasons be equipped with DALI drivers of the same brand!
Troubleshooting
- No light? Check the supply voltage. Measure the voltage at the terminal in the luminaire.
- For spotlights with track adapter: please check the positioning of the phase selector and the fixation to the track system.
- According to REACH (EC 1907/2006) we are obliged to inform you that this product may contain a low concentration of Lead (Pb) CAS 7439-92-1. Normal instructions for safe use applies, lead does not cause harm as it is incorporated in the chemical composition in the product and is not released in normal use. Please contact reach@fagerhult.se for more information.
It is appropriate to give this information to the user of the installation.
INSTRUCTION
Dwide
- TOOLS REQUIRED
- The luminaire MUST be connected before plugging in the mains voltage
- The light source, control gear and external cable shall exclusively be replaced by the manufacturer or its designated person
- Must not be covered with insulating matting
Dwide Organic Response
- TOOLS REQUIRED
- The luminaire MUST be connected before plugging in the mains voltage!
- The light source, control gear and external cable shall exclusively be replaced by the manufacturer or its designated person
Must not be covered with insulating matting
Dwide TW
- The luminaire MUST be connected before plugging in the mains voltage!
- The light source and control gear shall only be replaced by the manufacturer or its designated person
- Basic insulation betweenmains and control wiring.
Dwide TW and Organic Response
- The luminaire MUST be connectedbefore plugging in the mains voltage!
- Box space can not be covered with insulating matting
- For mounting in ventilated or unventilated space
- The light source and control gear shall only be replaced by the manufacturer or its designated person
Frame for HB ceiling Dwide
It is appropriate that this information is passed on to the users of the
installation.
Manufactured by Fagerhult Sweden. For UK market importer Fagerhult UK 33-34
Dolben Street, London, SE1 OUQ
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>