V-TAC VT-8603 20W LED Bulkhead Dome Light Instruction Manual

V-TAC VT-8603 20W LED Bulkhead Dome Light

Product Specifications

• Model: VT-8603, VT-8613, VT-8623, VT-8633
• SKU: 801-24, 804-24, 806-24, 812-24
• Beam Angle: >80 degrees
• CRI: DF
• Life Span: 30,000 hours
• Input Voltage: AC: 200-240V, 50Hz
• Material: PC
• Dimension: 320x100mm
• Warranty: 5 Year (VT-8603, VT-8613), 3 Year (VT-8623, VT-8633)

Product Usage Instructions

Installation Instructions

1. Switch OFF the power before starting the installation.
2. Remove the cover by holding the luminaire upside down. Press 3 clips on the sides and pull the base upwards to open and set aside.
3. Carefully press and unlock the screw on the LED hinged tray and hold the tray at an upward 90-degree position. Hold the product upside down.
4. Hold the product in place, mark & drill the holes into the wall and nail the alligator into the hole. Feed the supply cable into the luminaire through the cable entry hole.
5. Switch ON the power to test the light.

Instructions for Changing Color & Power (Available on Driver)

• CCT ON 3000K (Y)
• CCT ON 4000K (WY)
• CCT ON 6400K (W)

Pre-install Emergency Function Test

Power: 20W, 16W, 8W

Sensor Settings

FIG 1, FIG 2

Frequently Asked Questions (FAQ)

How do I contact support for queries or issues?
In case of any query/issue with the product, please reach out to us at support@vtacexports.com or visit V-TAC House, Kelpatrick Road, Slough, Berkshire, SL1 6BW, UK.

What should I do before disposing of the product?
This product should not be disposed of with other household wastes. Please contact the manufacturer or a qualified person for proper disposal instructions to avoid hazards.

WEEE Number: 80133970

TECHNICAL DATA

MODEL

| ****

SKU

| BEAM ANGLE| ****

CRI

| ****

DF

| LIFE SPAN (HOURS)| INPUT VOLTAGE| ****

MATERIAl

| ****

DIMENSION

| ****

WARRANTY

---|---|---|---|---|---|---|---|---|---
VT-8603| 801-24| 110°| >80| 0.9| 30,000| AC:200-240V, 50Hz| PC| 320x100mm| 5 Year
VT-8613| 804-24| 110°| >80| 0.9| 30,000| AC:200-240V, 50Hz| PC| 320x100mm| 5 Year
VT-8623| 806-24| 110°| >80| 0.9| 30,000| AC:200-240V, 50Hz| PC| 320x100mm| 3 Year
VT-8633| 812-24| 110°| >80| 0.9| 30,000| AC:200-240V, 50Hz| PC| 320x100mm| 3 Year

SENSOR SPECIFICATIONS

MODEL

| DETECTION ANGLE| DETECTION DISTANCE| DETECTION RANGE MAX.| ****

HOLD TIME

| DAYLIGHT SENSOR| MANUAL OVERRIDE| DETECTION MOTION SPEED
---|---|---|---|---|---|---|---

VT-8613 VT-8633

| 360° If Ceiling Mounting 120° If Wall mounting| ****

3-6 M

| ****

D6Mx3M

| ****

5s, 30s,90s,

3min,20min,30min

| ****

Day, 2LUX,10LUX-

,25LUX Optional

| ****

Available by dial switch

| ****

0.5-3m/s

EMERGENCY SPECIFICATIONS

MODEL

| EMERGENCY OPERATION TIME| ****

EMERGENCY STANDBY WATTS

| BATTERY CHARGING CURRENT| BATTERY DISCHARGING CURRENT| ****

BATTERY TYPE

| ****

TEST BUTTON

| ****

CHARGING INDICATOR

---|---|---|---|---|---|---|---
VT-8623| >3 Hours| >1.2 Watts| 250mA| 410mA| LiFePO4, 3.2V, 2Ah| With| Green LED

INTRODUCTION & WARRANTY

Thank you for selecting and buying V-TAC product. V-TAC will serve you the best. Please read these instructions carefully before starting the installing and keep this manual handy for future reference. If you have any another query, please contact our dealer or local vendor from whom you have purchased the product. They are trained and ready to serve you at the best. The warranty is valid for 5 years from the date of purchase. The warranty does not apply to damage caused by incorrect installation or abnormal wear and tear. The company gives no warranty against damage to any surface due to incorrect removal and installation of the product. The products are suitable for 10-12 Hours Daily operation. Usage of product for 24 Hours a day would void the warranty. This product is warranted for manufacturing defects only.

WARNING

• Please make sure to turn off the power before starting the installation.
• Installation must be performed by a qualified person.
• The light source of this luminaire is not replaceable, when the light source reaches its end of life the whole luminaire should be replaced.
• If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard.

INSTALLATION INSTRUCTIONS

1. Switch OFF the power before starting the installation.
2. Remove the cover by holding the luminaire upside down. Press 3 clips on the sides and pull the base upwards to open and set aside.
3. Carefully press and unlock the screw on the led hinged tray and hold the tray at an upward 90Degree position. Hold the product upside down.
4. Hold the product in place, mark & drill the holes into the wall and nail the alligator into the hole. Feed the supply cable into the luminaire through the cable entry hole
5. Once the base is installed, carefully put back the hinged tray by pushing it forward.
   • Hold the tray with the base and twist the screw to lock it back.
6. Carefully close the cover by aligning with the marked arrows on the base ( Locate the Side conduit) and the cover to avoid breakage while closing.
   • Push down from all 3 sides to properly secure the 3 clips on the sides.
7. Switch ON the power to test the light.

INSTRUCTIONS FOR CHANGING COLOR & POWER (AVAILABLE ON DRIVER)

PRE-INSTALL EMERGENCY FUNCTION TEST

• Connect the AC cable according to the diagram.
• Press the test button on the driver. The emergency function will be activated, and the charging indi-cation will be off.
• Disconnect the battery pack, the charging indicat-ed LED off.

NOTE: After installation, allow 36 hours to ensure full battery charge and then interrupt the supply.

SENSOR SETTINGS

• Detection Area – It can be adjusted by combining DIP switches for specific application [FIG 1].

• Hold Time – Time period during which the light will be ON after the last detection [FIG 2].

• Daylight Threshold – Daylight sensor priors motion sensor. Set Threshold for Specific needs. If disabled, only motion sensor will work [FIG 3].

SENSOR APPLICATION

When motion is detected, but the daylight is sufficient, the light will remain OFF.

When motion is detected, and the daylight is insufficient, the light will be ON.

After a stand-by period, the light will switch OFF.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>