PROSAUNAS BP031172 Two 10-FT Flexible LED Strips Instructions

: September 12, 2024
: PROSAUNAS

Table of Contents

Installation and Operation
SAFETY & WARNINGS
Electrical Requirements
PACKAGE CONTENTS
SPECIFICATIONS
LED HANDLING
INSTALLATION
Read User Manual Online (PDF format)
Download This Manual (PDF format)

**PROSAUNAS BP 031172 Two 10-FT Flexible LED Strips Instructions

**

Installation and Operation

Compatible with Most Sauna Heater Controls & On/Off Switches

SAFETY & WARNINGS

PLEASE READ THIS MANUAL IN ITS ENTIRETY PRIOR TO INSTALLATION!

Qualified Personnel Only: Installation of this system must be performed by a certified electrician, following all national electric code and local building code requirements.
Equipment Protection: The power supply must be installed in a location that is completely protected from moisture, rain, and inclement weather.
Temperature Considerations: Please refer to the specifications on page 4 to determine the maximum temperature rating of each component. Do not install any components in areas that exceed their maximum temperature limits, as this will lead to product failure and void the warranty.
Heater Clearance: Maintain a safe distance between your Flexible LED light and the sauna heater.
Avoid directly installing the lights above the heater or within 20 inches of its sides.
Light Placement: Carefully consider the placement of your LED lights to avoid shining directly into eyes. A diffused or indirect lighting approach is recommended.
Handling Precautions:
- Uncoil Before Powering: Do not connect power to the LED light while it is still attached to the spool or coiled up. Unwind the light completely before powering it on.
- Avoid Damage: Refrain from folding or twisting the LED light, as this can cause physical damage to the LEDs and lead to malfunctions, refer to page 5 for LED Handling.

Electrical Requirements

Always disconnect power from the system at the circuit breaker before performing any electrical installation or maintenance.

Power Source : The lighting system requires a 120 V AC power source.
Qualified Electrician : A certified electrician should determine the appropriate electrical outlet type, box configuration, and necessary wiring to ensure compatibility and safety.
Electrical Safety : Utilizing improper voltage or making incorrect electrical connections can damage system components and void the warranty.

PACKAGE CONTENTS

10 FT Flexible LED Neon BP 031172 (qty. 2)

Mounting Clip + Screw BP031165 (qty. 22 each)

End Cap B P 031106 (qty. 2)

Silicone BOSS- 31560 (qty. 1)

Note: Replacement part numbers listed above each part

Power Supply BP 031137 (qty. 1)

AC Power Cord BP 031132 (qty. 1)

30 FT Light Cable BP031081 (qty. 2)

2-Way DC Splitter BP031114 (qty. 1)

SPECIFICATIONS

Flexible LED Neon x 2

Length| Operating Voltage (V D C)| Wattage| Lumens| Kelvin Temperature| Operating Temperature| IP Rating| Certification
10 FT(per light)| 24 V DC| 3W (per foot)30W (per light)| 990(per light)| 3500 K| -13°F to 200°F| IP67| ETL / SGS
Power Supply

LED HANDLING

HANDLE LED LIGHT WITH CARE!
Cutting Flexible LED Neon

Determine the length of LED needed for the installation location
Using sharp cutters or scissors cut at closest cut point to the length needed, see diagram below.
Note: Cut only on marked lines.
After cutting to length apply silicone to cut end and install end cap.

Cut on Marked Lines Only

Cutting Length 1.96”

INSTALLATION

STEP : 1. Identify LED Install Location
Identify location where LED light will be installed.
Common installation spots are,

Backrest shining up or down
Under bench
Sauna Floor
Exterior Sauna

STEP 2. LED Mounting Clips

Grab Mounting Clips and screws. Clips are provided with 1 screw each.
If using your own screw you will need a minimum size #4 x 5/8” screw to mount clips.
It is recommended that clips be mounted every 8”to 12” to support LED light.
Take LED and gently press light into each clip.
Follow connection diagram on page 4 for LED wire connections.

Important:

LED Light should not be installed above or within 20” of sauna heater.
“Always check temperature at install location of LED light and ensure it does not exceed maximum operating temp.”
Note: It is recommended to run sauna without LED light installed and check temperature at intended install location to get an accurate temperature.

Note: Images below show examples of clip installation.
To remove LED from clip gently pull up on LED at each clip to release, avoid bending LED as this will damage the light.
STEP 3. Power Supply Connection
Determine how power supply will be powered, this can be from a standard 120 VAC receptacle or wired into your Sauna equipment power module, see images below for wiring.

Important
Images below are shown as a reference. It is important to verify heater manufacturers installation steps for connecting lighting.

Huum
Main Module

120 VAC Receptacle
(wired to on/off switch)

Saunum
Air IQ Power Unit

Harvia
CX30 / CX45 / CX170

Technical Support :224-253-5909