FORMOVIE ALR Motorized Floor Rising Screen User Manual

FORMOVIE ALR Motorized Floor Rising Screen User Manual

Warning
Do not expose the product to rain or moisture to reduce the risk of fire or electric shock. Please strictly abide by the following safety rules. Incorrect installation and use methods may cause device damage or personal injury

1. When moving the screen, handle the screen carefully to avoid damage.
2. Do not put the liquid on the product or expose the product to rain.
3. Fire protection and heat protection: Keep away from heat sources, such as radiators, stoves, and other harmful products.
4. This product is equipped with a strong cross-spring system, please do not try to disassemble it by yourself to prevent accidents.
5. Check and determine whether the power supply voltage and frequency are consistent with the rated voltage of this product, and the power socket should have a reliable grounding wire.
6. Avoid from scratching or folding the screen, so as not to cause the curtain to be damaged or wrinkled.
7. After the screen is used, please retract the screen into the shell to prevent the screen from being polluted by dust and reduce light aging. Before retracting the screen, please check and make sure that the screen is clean and free of foreign objects.
8. Continuous raising/retracting for 4 minutes activates the thermal protection feature. Please avoid frequently raising/retracting the screen in a short period.
9. Ensure the screen is level during installation. The mounting surface must be hard and deformation-free. Screws should be securely fastened to prevent tilting during use.
10. This screen is equipped with a remote control transmitter, please remove the batteries when not in use for extended periods.
11. Please operate according to the instruction manual. Please contact professional service staff for maintenance-related issue.

Screen Cleaning

1. Dry Cleaning: Dust the screen lightly with a feather duster or rub gently with an eraser.
2. Wet Cleaning: Gently wipe with a soft cloth dipped in clean water or diluted mild alkaline cleaner; do not use alcohol, ether, or similar solvents to avoid deforming the screen.

Characteristic

1. Equipped With voice function,
2. Adopt a self-leveling system (that is, when the screen rises to the highest state, it will automatically drop about 5CM to maintain the relatively flat state of the screen);
3. This product is equipped with a USB trigger (code has been matched before delivery), which can be inserted into the USB port of the projector for use as needed;
4. Easy to install and fix, suitable for ground, wall, and cabinet installation.

Notice:
After unpacking, confirm whether the accessories are complete

Confirm the installation method of the base according to the site conditions, as shown in the figure below. (The base may be unrolled left and right or forward and backward as needed; it has been retracted to the bottom of the shell before leaving the factory.)

The base‘s condition upon leaving the factory

Rotate and adjust the base to unroll forward and backward

Rotate and adjust the base to unroll left and right

If conditions permit, fix the mounting holes with screws.

If you need to fix it on the wall or the side of the cabinet, you can refer to the figure below to make the mounting bracket, and the figure after installation is shown below.

Restore Factory Setting

• Press and hold the ‘pause’ button on the transmitter for 5 seconds.

• Enter setup mode signaled by a quick “beep”.

• Hold down the U2 button at the back of the transmitter until you hear a long “beep”.

• Factory reset successfully completed.

• After resetting to factory settings, please strictly follow the steps below for configuration.

• After resetting to factory settings, the remote control buttons become ineffective.
  Single tapping the up and down keys on the screen control panel will put it in fine-tuning mode, while long pressing these keys will raise or retract the screen.

• Before re-pairing the remote control, you need to power off the screen and then restart it.

• The U1 button at the back of the remote control is a non-functional button.

Remote Control Code Pairing

• First, power off the screen and then restart it.
• Press and hold the ‘up’ button on the transmitter for 5 seconds.
• Enter code learning mode indicated by a slow “beep”.
• Release and press ‘up’ again until a long “beep” is heard.
• Code pairing successful.

Maximum Rising Position

• Hold the Up button to lift the screen.

• Important: Without a Maximum Rising Position set, the motor will idle and the screen will slack when at its highest. Press “Pause” immediately to prevent reversal.

• Simultaneously press Up and Pause once for a long beep, initiating the Maximum Rising Position setting mode.

• In the setting mode (jog mode), adjust the screen to its highest and tight position using single touches of the up and down keys.

• After adjusting, press Up and Pause together again for a long beep.

• Maximum Rising Position is set successfully.

• The screen’s Maximum Rising Position has been preset before leaving the factory.

• The Maximum Rising Position refers to the highest height the screen should reach.
  Exceeding this limit may result in motor idling, screen slackness, and screen inversion.

• Normally, there is no need to change the Maximum Rising Position.
  The Maximum Rising Position only needs to be reset after restoring the factory settings.

Upper Limit Setting

• Press the Up and Down button on your remote to adjust screen height.
• Pause at desired height.
• Press Up and Pause button together once for setting mode (confirmed by long beep).
• Press Up and Pause button together again for another long beep.
• Upper Limit Setting Successful.
• The upper limit has been preset before leaving the factory.
• The upper limit only needs to be reset after restoring the factory settings.

Lower Limit Setting

• Press “Down” and “Pause” together to enter lower limit setting mode (confirmed by long beep).
• Tap “Down” button to fine-tune screen position.
• Once screen is at desired position, press “Down” and “Pause” together again for another long beep.
• Lower Limit Setting Successful.
• The lower limit has been preset before leaving the factory.
• The lower limit only needs to be reset after restoring the factory settings.
• When the screen cannot be retracted back into the shell and the cover cannot be closed, adjusting the lower limit can serve as a solution.

Transmitter

Pair code of the trigger
(After entering the pairing/deleting mode, if the receiver beeps slowly for 30 seconds and there is no corresponding operation, the receiver will return to the initial state)

Pair code setting Within 30 seconds after turning on the power, insert the trigger into the audio interface of the projector, and press the stop button of the receiver for 5 seconds, the receiver beeps slowly, press the pairing key of the receiver 2 times within 5 seconds, the receiver beeps 3 times quickly, The indicator light stops flashing, and the code pairing is successful.

WIFI formatting

(Note: Products that have been connected to the network need to connect to a new network or a new mobile phone, and the network needs to be cleared and formatted first)

Network formatting operation Long press the U2 key on the back of the transmitter for 7 seconds, and “beep” sound once slowly, then long press the down key for the transmitter for 2 seconds, and a quick “beep” sound occurs for three times, and the network clearing operation is successful.

General Troubleshooting

Common problem| Inspection site and cause analysis| Solution
---|---|---
The motor does not work| Check the power supply, whether it is powered on| Connect the power plug socket
The motor works continuously for more than 4 minutes, automatic overheating protection will be triggered.| Wait for 30 minutes for the motor to cool down and power on automatically
The three-position switch or the circuit of the remote control receiving box is malfunctional resulting in the motor not being energized| Replace corresponding parts
Three-position switch failure| Press the reset button (middle button) on the remote controller
The remote control does not work| The battery of the remote controller is low| Replacement battery
Out of range| The factory generally sets the remote control distance: wireless <50 meters
The remote control transmitter does not match the receiver| Re-code
Try other control methods (such as manual control) to determine whether there is a motor problem| Determine whether the remote control is faulty
Screen fabric shift| Violent shaking during transportation leads to loosening, or the position adjusted by the user| Adjust the position of the screen according to the method in the manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>