Gladiator GANA201BMS Flex Cabinet System Bracket Instruction Manual

June 13, 2024
GLADIATOR

FLEX BRACKET
Assembly Instructions
Models: GANA201BMS

BRACKET SAFETY

Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:

DANGER : You can be killed or seriously injured if you don’t immediately follow instructions.

WARNING You can be killed or seriously injured if you don’t follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

ASSEMBLY INSTRUCTIONS

Tools and Parts

Gladiator GANA201BMS Flex Cabinet System Bracket -
Parts

Gather the required tools and parts before starting installation.
Tools Needed:

  • 1 Socket Wrench with 10mm Socket
  • 4mm Hex Wrench
  • Tape measure

Parts Supplied:

  • Bracket(1)
  • M6 hex flange nuts (4)
  • M6 round head square neck bolts (4)

Bracket Use Requirements

  • Intended for use on Gladiator ® Flex Cabinet Systems’ cabinets (sold separately).

Install the 30″ Tall Cabinet
NOTE : Flex Brackets are sold individually and Gladiator ® GearTrack ® channels are sold separately.

  1. Install the brackets to the tall cabinet.
    ■ Attach the top bracket (P1) to the tall cabinet’s back top with four M6 round head square neck bolts (F1) and four M6 flange nuts (F2).
    ■ Attach the center and bottom brackets (P1) to the tall cabinet’s back respectively with two M6 round head square neck bolts (F1) and two M6 flange nuts (F2).
    WARNING
    Excessive Weight Hazard
    Use two or more people to move and install cabinet.
    Failure to do so can result in back or other injury.

  2. Hang the tall cabinet onto the GearTrack ® channels
    ■ Make sure all three brackets (P1) are fully engaged in the slots as shown.
    NOTE : For installation of the Gladiator ® GearTrack ® channels, please refer to the manual instructions included with the Gladiator ® GearTrack ® channels.Gladiator GANA201BMS Flex Cabinet System Bracket -
bracketsThe GearTrackchannels should be installed with the spacing as shown.

Install the 24” Flex Wall Cabinet
NOTE : Flex Brackets are sold individually and Gladiator ® GearTrack ® channels sold separately.

  1. Attach two M6 x 16 hex socket head screws (F3) to the bracket (P1) as shown.
  2. Attach the bracket (P1) to the wall cabinet’s back top.Gladiator GANA201BMS Flex Cabinet System Bracket - cabinet ■ Attach the bracket (P1) to the wall cabinet’s back top with four M6 round head square neck bolts (F1) and four M6 flange nuts (F2).
  3.  Hang the wall cabinet onto the GearTrack ® channel.Gladiator GANA201BMS Flex Cabinet System Bracket - GearTrackThe GearTrack ® channels should be installed with the spacing as shown. ■ Make sure the bracket is fully engaged in the wall slots as shown. Tighten the pre-attached M6 x 16 hex socket head screws fully into the bracket and make sure they go into the wall slots.
    NOTE : If installing the wall cabinet on GearTrack ® channels, a second channel must be installed 6″(15.24cm) below the bottom of the supporting channel so the cabinet will hang level.
    NOTE : For installation of the Gladiator ® GearTrack ® channels, please refer to the manual instructions included with the Gladiator ® GearTrack ® channels.

Install the 24″Flex 2-door Base Cabinet
NOTE : Flex Brackets are sold individually and Gladiator ® GearTrack ® channels are sold separately.

  1. Install the brackets (P1) to the cabinet.Gladiator GANA201BMS Flex Cabinet System Bracket - flange ■ Temporarily turn the base cabinet upside down as shown.
    ■ Attach the brackets to the back of the base cabinet as shown with eight M6 round head square neck bolts (F5) and eight M6 flange nuts (F3).
      WARNING
    Excessive Weight Hazard
    Use two or more people to move and install cabinet.
    Failure to do so can result in back or other injury.

  2. Hang the base cabinet onto the GearTrack ® channelsGladiator GANA201BMS Flex Cabinet System Bracket - cabinet5The GearTrack ® channels should be installed with the spacing as shown.Gladiator GANA201BMS Flex Cabinet System Bracket - spacing2 ■ Hang the base cabinet onto the GearTrack ® channels. Make sure the two brackets are fully engaged in the slots as shown.
    NOTE : For installation of the Gladiator ® GearTrack ®  channels, please refer to the manual instructions included with the Gladiator ® GearTrack ® channels.

Install the 24″ Flex 1-drawer 2-door Base Cabinet
NOTE: Flex Brackets are sold individually and Gladiator ®  GearTrack ® channels are sold separately.

  • Remove the drawer from the base cabinet.
  • Follow the same procedure as the 24″ 2-door base cabinet to attach the brackets and attach the cabinet onto the GearTrack ® channels.
  • Install the drawer back to the base cabinet.

WARRANTY

For warranty information:
In the U.S.A. call 1-866-342-4089 or visit our website at www.GladiatorGW.com
In Canada call 1-800-807-6777 or visit our website at www.gladiatorgarageworks.ca
Limited Lifetime Parts Warranty for metal parts.
The warranty excludes incidental / inconsequential damages and failure due to misuse, abuse or normal wear and tear.
In U.S.A. call: 1-866-342-4089

® /™ ©2022 Gladiator. All rights reserved.
W11637535A

Documents / Resources

| Gladiator GANA201BMS Flex Cabinet System Bracket [pdf] Instruction Manual
GANA201BMS Flex Cabinet System Bracket, GANA201BMS, Flex Cabinet System Bracket, System Bracket, Bracket
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

GLADIATOR User Manuals

Related Manuals