Ronix 4110 Electric Jig Saw Instruction Manual

Ronix 4110 Electric Jig Saw

Specifications

• Model: 4110
• Power: 600W
• Voltage: 220-240V
• Frequency: 50-60Hz
• Max Capacity in Wood: 130mm
• Max Capacity in Metal: 10mm
• Jig Saw Blade Type: T-shank
• Orbital Action: 4-Position
• No-load Speed: 500-2500RPM
• Weight: 3Kg
• Supplied in: BMC
• Includes: 2 Jig saw Blades, Dust Extraction Connector, Guide rule

Product Usage Instructions

Basic Safety Precautions
When using the electric jig saw, always observe the safety instructions to reduce the risk of fire, electric shock, and personal injury. Keep the work area clean and avoid damp or wet locations. Do not expose the tool to rain or inflammable liquids.

Fitting and Removing a Saw Blade
Before assembly or adjustment, always unplug the tool.

1. Fitting the Blade:
   • Open the blade holder by retracting the blade latch.
   • Insert the saw blade into the holder, guiding the back into the guide roller groove.
   • Release the blade latch to assemble the blade securely.
2. Removing the Blade:
   • Release the blade latch and fully retract it to pull the blade out of the holder.

Saw Blades Instruction

Setting the Pendulum Action
The pendulum action settings allow adaptation of cutting speed, capacity, and pattern. Adjust in four steps with the lever while the machine is running. Follow these steps:

1. Release the shoe lever.
2. Slide the shoe toward the saw blade.
3. Tilt the shoe and set the desired bevel angle using the scale.
4. Tighten the shoe lever.

Switching On and Off
Please ensure that the switch is off when plugging the tool into an electricity socket.

PART LIST

SAFETY INSTRUCTIONS

WARNING!
when using electric tools, all the safety instructions should always be observed to reduce the risk of fire, electric shock and personal injury before attempting to operate the tool, please read all the instructions and save it for further reference.

BASIC SAFETY PRECAUTIONS FOR ALL ELECTRIC TOOLS

1. Keep work area clean Cluttered areas and benches invite injuries.

2. Consider the work area environment
   Don’t use electric tools in damp or wet locations. Don’ t expose electric tools to rain. Keep work area well, In particular, no inflammable liquids or gases must be present.

3. Avoid electric shock.
   when you are operating tools, don’t touch metal being grounded, such as pipe, radiator, freezer, etc.

4. Keep children and visitors away
   Don’t let children contact tool or extension cord. All visitors should be kept away from work place.

5. Store idle tool
   when not in use, tools should be stored in dry, high, or locked up place.

6. Don’t force tool
   It will do the job better and safer at the rate for which it was intended, Avoid unnecessary overload which may put the operator at risk and impair functions of the tools.

7. Use right tool
   Don’t force small tools and attachment to do the job of a heavy duty tool. Don’t use tools for purpose not intended, for example, don’t use electric circular saw for cutting logs or tree limbs.

8. Dress properly
   Don’t wear loose clothes or jewelry. They can be caught in moving parts. Rubber gloves and non- skid footwear are recommended when working outdoors. Wear protective hair covering to contain long hair.

9. Use safety goggles
   Always wear safety goggles. If dust is produced, use the special masks.

10. Don’t abuse cables
    Never carry tool by cable or yank it to disconnect it form socket. Keep cable from heat, oil and sharp edges.

11. Don’t overreach
    Keep proper footing and balance at all times.

12. Maintain tools with care
    Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and replace if damaged. Keep handles dry, clean and free from oil and grease.

13. Disconnect tools
    when not in use, before servicing, and when changing accessories such as blades, bits and cutters.

14. Remove adjusting keys wrenches
    from the habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on.

15. Avoid unintentional starting
    Don’t carry plugged in tool with finger on switch. Make sure switch is off when connecting the plug to the socket.

16. Use extension cord
    If an extension cord is required, always check that its cross section measurement is equal to or greater then that of the tool capabilities and so marked.

17. Stay alert
    Watch what you are doing. Use common sense. Do not operate tool when you are tired.

18. Check damaged parts
    Before further use of the tool, a guard or other parts that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving part, breakage of parts, mounting and any other condition that may affect its operations, A guard or other part that is damaged should be properly repaired or replaced by a qualified service center unless otherwise indicated elsewhere in the instruction manual. Have defective switches replaced by a qualitied service center. Do not use tool if switch does not turn on and off.

19. Check the voltage
    Do not plug the electric tool into the mains until you have checked that the voltage shown on the data plate corresponds to the voltage available.

20. Replace parts
    The use of improper accessory or attachment other than recommended present a risk of personal injuries.

21. Have your tool repaired by an expert
    This electric tool is in accordance with the relevant safety regulations. Repairing of electric tool may be carried out only by expert. Otherwise, it may cause considerable danger of the user.

JIG SAW USE
This jig saw is intended for the cutting of wood pieces, steel, aluminum, plastic with different types of cutting blade.

ADDITIONAL SAFETY REGULATIONS

1. before using the tool, please check the switch is off and the plug is not connected to electricity socket.
2. The tool should not touch any objects when turning on the tool to avoid any danger.
3. Before plug in the electricity socket, please make sure the machine is switched off and put the cable on back side.
4. Switch on the tool, then start cutting on work piece.
5. Don’t touch the moving parts especially the blade.
6. Make sure there is no obstacle objective on work piece.
7. Hold the tools tightly when operating the tool.
8. Don’t lay down the tool on the ground or working table before switch it off.
9. Don’t cut the material with asbestos. When cutting some material like fiber, please wear mask.
10. When switch off the tool, don’t stop the blade by pressing, Don’t touch the blade by hand because it is quite hot when just stop working.
11. Only use sharp and indefective blade. The blade must be replaced if it is broken, with crack, distorted or blunt.
12. If the extended cord need, please use the same type of the tool.
13. If the working surrounding is too hot, damp or too much dust, please use an circuit cut device to assure the safety of operator.

OPERATION REGULATIONS

FITTING AND REMOVING A SAW BLADE
NOTE : Prior to assembly and adjustment, always unplug the tool. This tool has SDS system for quick and easy changing of saw blade.

FITTING THE BLADE

• Open the blade holder by fully retracting the blade latch.
• Insert the saw blade into the blade holder, guiding the back of the blade into the groove of the guide roller.
• Release the blade latch, the blade is assembled well.

REMOVING THE BLADE
Release the blade latch, fully retract the blade latch and pull the blade out of the holder.

SAW BLADES INSTRUCTION
The blade is supplied with customers’ requirements. The above blades may not be supplied with tool.

SETTING THE PENDULUM ACTION
The four pendulum action settings allow optimum adaptation of cutting speed, cutting capacity and cutting pattern to the material being sawed. The pendulum action can be adjusted in four steps with the adjustment lever.

Switching is possible with the machine running:

SETTING THE BEVEL ANGLE
The adjustable shoe allows cutting of left hand or Right hand bevel angles from 0 – 45°. The bevel scale has preset positions at 0° , 15° , 30° , 45°

• release the shoe level.
• Slide the shoe toward the saw blade.
• Tilt the shoe and set the desired bevel angle by using the scale
• Tighten the shoe lever.

SWITCHING ON AND OFF
Note: please make sure that the switch is off when the tool plug into electricity socket.

1. To run the tool, press the on/ off switch.
2. For continuous operation , press and hold down the switch, press the lock- on button and release the switch.
3. To stop the tool, release the switch.
4. To stop the tool in continuous operation, press the switch briefly and release it. Always switch off the tool when work is finished and before unplugging.

SETTING THE ELECTRONIC SAWING SPEED
To preset the sawing speed, turn the control dial to the desired level. The higher the rate, the higher the sawing speed. The required setting depends on the thickness and kind of material. Using high speeds for sawing soft materials such as wood, Use low speeds for sawing metal. Please refer to below information.

• Working Objective Control Dial Level
• Wood 5-6
• Sheet steel 3-6
• Stainless steel 3-4
• Aluminum 2-3
• Plastic 1-4

EFFECTIVE AND SAFE CUTTING

NOTE:
Please lubricate the guide rather frequently.

• If necessary . draw a cutting line.
• Drill a hole (¢ Min.12mm and introduce the saw blade) Switch the tool on. follow the line when cutting straightly.

For pendulum cutting. Please move the tool slightly.

1. Sawing in metal

   • Mount an appropriate saw blade.
   • Proceed as described above.
   • Use a cooling lubricant (cutting oil to prevent overheating of the saw blade or the workpiece)

2. Mounting the plastic anti scratch shoe cover.
   When cutting some decoration material or plastic workpiece, please use the anti- scratch shoe cover in order to protect the working surface .

3. Use sawdust blower lever
   The sawdust conducts an adjustable stream of air to the saw blade to keep the workpiece clear of sawdust during operation.

   • Set the sawdust blower using the lever
   • Low For working with metals, when using coolants and lubricants and for use with dust extraction.
   • Intermediate For working with wood and similar materials in low speed.
   • High For working with wood and similar materials in high speed.

4. Dust extraction
   When the tool is used indoor for extended periods of time, use a suitable dust extractor designed in compliant with applicable directives regarding dust emission. The dust extraction tube in combination with the dust protector helps extracting the dust from the workpiece surface, when connected to a suitable dust extraction system.

SERVICE AND MAINTENANCE

1. Always disconnect the tool before carrying out inspection or cleaning.
2. Never use water or other liquids to clean the tool. Clean the tool by brushing it with a brush.
3. Check and replace the carbon brush frequently.
4. The air vent of the tool should be cleaned regularly to avoid the motor too hot due to air vent blocked.
5. Always check if the components of the tool are fixed well.
6. The parts of tool should be without trace of crack or damage.
7. Always check if the cable is without damage.

REPLACING THE CARBON BRUSHES
NOTE: The carbon brush of this tool is internal type. Please replace the carbon
brush only by our maintenance service center or dealers. Don’t replace it by yourself.

• Replace the carbon brushes when the tool does not run and makes too much sparkle.
• Carbon brushes which are worn out ( burned, broken or shorter than 5mm) have to be replaced by new ones.
• Always replace both carbon brushes at the same time and use the brush by RONIX SERVICE
• The brushes have to fall in the holders easily.
• After placing the new carbon brushes, let the tool run for some minutes so that the brushes fit better.

SCAN THE QR CODE

www.ronixtools.com

FAQ

Q: What materials can be cut using this electric jig saw?
A: This jig saw is intended for cutting wood pieces, steel, aluminum, and plastic with different types of cutting blades.

Q: How many pendulum action settings are available?
A: The jig saw offers four pendulum action settings for optimizing cutting speed, capacity, and pattern based on the material being sawed.

Q: What is included in the BMC package?
A: The BMC package includes 2 jigsaw blades, a dust extraction connector, and a guide rule.

References

• Global Power Tools | Hand Tools | Cutting Tools | ? Ronix Tools

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>